Miniature Viscous Disk Pump: Performance Variations From Non-Newtonian Elastic Turbulence

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Phil Ligrani ◽  
Benjamin Lund ◽  
Arshia Fatemi
Keyword(s):  
Pump Power ◽  
Water Solution ◽  
Flow Behavior ◽  
Pure Water ◽  
Pressure Rise ◽  
Volumetric Flow Rate ◽  
Flow Coefficient ◽  
Polyacrylamide Solution ◽  
Water Flows ◽  
Specific Speed

Within the present investigation, a miniature viscous disk pump (VDP) is utilized to characterize and quantify non-Newtonian fluid elastic turbulence effects, relative to Newtonian flow behavior. Such deviations from Newtonian behavior are induced by adding polyacrylamide to purified water. The VDP consists of a 10.16 mm diameter disk that rotates above a C-shaped channel with inner and outer radii of 1.19 mm and 2.38 mm, respectively. A channel depth of 230 μm is employed. Fluid inlet and outlet ports are located at the ends of the C-shaped channel. Experimental data are given for rotational speeds of 126 1/s, 188 1/s, 262 1/s, and 366 1/s, pressure rises as high as 700 Pa, and flow rates up to approximately 0.00000005 m3/s. Reynolds number ranges from 2.9 to 6.5 for the non-Newtonian polyacrylamide solution flows and from 51.6 to 149.8 for the Newtonian pure water flows. To characterize deviations due to non-Newtonian elastic turbulence phenomena, two new parameters are introduced, PrR and HCR, where HCR is the ratio of head coefficient (HC) for the polyacrylamide solution and head coefficient for the water solution, and PrR is the ratio of pump power for the polyacrylamide solution and pump power for the water solution. Relative to Newtonian, pure water flows, the polyacrylamide solution flows give pump head coefficient data, dimensional pressure rise data, slip coefficients (SCs), specific speed (SS) values, and dimensional power data, which show significant variations and differences as they vary with flow coefficient (FC) or dimensional volumetric flow rate. Also important are different ranges of specific speed (SS) for the pure water and polyacrylamide solutions, and a lower range of SC or slip coefficient values for the polyacrylamide solution flows, compared to the pure water flows. These variations are due to increased elastic turbulence losses, which occur as viscosity magnitudes increase and the elastic polymers are excited by mechanical stress, which causes them to extend, deform, stretch, and intertwine.

Deviations Due to Non-Newtonian Influences Within a Miniature Viscous Disk Pump

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Phil Ligrani ◽  
Hui Jiang ◽  
Benjamin Lund ◽  
Jae Sik Jin
Keyword(s):  
Newtonian Fluid ◽  
Flow Rate ◽  
Rotational Speed ◽  
Stokes Equations ◽  
Sucrose Concentration ◽  
Pure Water ◽  
Pressure Rise ◽  
Volumetric Flow Rate ◽  
Newtonian Flow ◽  
Newtonian Behavior

A miniature viscous disk pump (VDP) is utilized to characterize and quantify non-Newtonian fluid deviations due to non-Newtonian influences relative to Newtonian flow behavior. Such deviations from Newtonian behavior are induced by adding different concentrations of sucrose to purified water, with increasing non-Newtonian characteristics as sucrose concentration increases from 0% (pure water) to 10% by mass. The VDP consists of a 10.16 mm diameter disk that rotates above a C-shaped channel with inner and outer radii of 1.19 mm, and 2.38 mm, respectively, and a channel depth of 200 μm. Fluid inlet and outlet ports are located at the ends of the C-shaped channel. Within the present study, experimental data are given for rotational speeds of 1200–2500 rpm, fluid viscosities of 0.001–0.00134 Pa s, pressure rises of 0–220 Pa, and flow rates up to approximately 0.00000005 m3/s. The theory of Flumerfelt is modified and adapted for application to the present VDP environment. Included is a new development of expressions for dimensionless volumetric flow rate, and normalized local circumferential velocity for Newtonian and non-Newtonian fluid flows. To quantify deviations due to the magnitude non-Newtonian flow influences, a new pressure rise parameter is employed, which represents the dimensional pressure rise change at a particular flow rate and sucrose concentration, as the flow changes from Newtonian to non-Newtonian behavior. For 5% and 10% sucrose solutions at rotational speeds of 1200–2500 rpm, this parameter increases as the disk dimensional rotational speed increases and as the volumetric flow rate decreases. Associated magnitudes of the pressure difference parameter show that the fluid with the larger sucrose concentration (by mass) produces significantly larger differences between Newtonian and non-Newtonian fluid flow, for each value of dimensional volumetric flow rate. For each disc rotational speed, compared to Newtonian data, dimensional pressure rise variations with dimensional volumetric flow rate, which are associated with the non-Newtonian data, are generally lower when compared at a particular volumetric flow rate. Agreement with analytic results, for any given flow rate, rotational speed, and flow passage height, validates the shear stress model employed to represent non-Newtonian behavior, as well as the analytic equations and tools (based upon the Navier–Stokes equations) which are employed to predict measured behavior over the investigated range of experimental conditions.

Association of Graft Copolymers of Alkyl Methacrylates with α-Methyl-ω-hydroxy-poly(oxyethylene) ethacrylates

1995 ◽  
Vol 60 (11) ◽  
pp. 1971-1985 ◽  
Author(s):  
Čestmír Koňák ◽  
Zdeněk Tuzar ◽  
Pavla Kopečková ◽  
Joseph D. Andrade ◽  
Jindřich Kopeček
Keyword(s):  
Light Scattering ◽  
Graft Copolymers ◽  
Water Solution ◽  
Pure Water ◽  
Solution Properties ◽  
Monomer Composition ◽  
Special Procedure ◽  
Methyl Cellosolve ◽  
Hexyl Methacrylate ◽  
Alkyl Methacrylates

Solution properties of the statistical copolymers of alkyl methacrylates (AMA) with α-methyl-ω-hydroxy-poly(oxyethylene) methacrylates (MPOEMA) (nonionic polysoaps) were studied using static and dynamic ligh scattering as a function of monomer composition and concentration in aqueous and methyl cellosolve solutions. The solubility of the copolymers in water was found to be dependent on molar contant of AMA. While copolymers with low content of hexyl methacrylate (HMA) (0 and 20 mole %) were directly soluble in water, forming true solutions with a low content of large swollen aggregates, copolymers with a higher content of HMA or lauryl methacrylate (LMA) were not directly dispersable in water. A special procedure, the stepwise dialysis from methyl cellosolve solutions against water, had to be used to prepare them in the pseudomicellar form. The copolymers were directly soluble in methyl cellosolve and its water solution containing up to 60 vol.% of water. Nevertheless, the light scattering experiments were dominated by light scattering of swollen particles of aggregated copolymer molecules. The copolymers were not soluble in the mixtures containing 70-100 vol.% of water. Paramaters of aggregates in the mixture with 60 vol.% of water and in pure water were found to be very similar.

scholarly journals Behavior and properties of water in silicate melts under deep mantle conditions

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Bijaya B. Karki ◽  
Dipta B. Ghosh ◽  
Shun-ichiro Karato
Keyword(s):  
Electrical Conductivity ◽  
Molar Volume ◽  
Water Solution ◽  
Pure Water ◽  
Electrical Conductance ◽  
Water Structure ◽  
Bulk Water ◽  
Silicate Melts ◽  
Pressure Regime ◽  
Low Pressures

AbstractWater (H2O) as one of the most abundant fluids present in Earth plays crucial role in the generation and transport of magmas in the interior. Though hydrous silicate melts have been studied extensively, the experimental data are confined to relatively low pressures and the computational results are still rare. Moreover, these studies imply large differences in the way water influences the physical properties of silicate magmas, such as density and electrical conductivity. Here, we investigate the equation of state, speciation, and transport properties of water dissolved in Mg1−xFexSiO3 and Mg2(1−x)Fe2xSiO4 melts (for x = 0 and 0.25) as well as in its bulk (pure) fluid state over the entire mantle pressure regime at 2000–4000 K using first-principles molecular dynamics. The simulation results allow us to constrain the partial molar volume of the water component in melts along with the molar volume of pure water. The predicted volume of silicate melt + water solution is negative at low pressures and becomes almost zero above 15 GPa. Consequently, the hydrous component tends to lower the melt density to similar extent over much of the mantle pressure regime irrespective of composition. Our results also show that hydrogen diffuses fast in silicate melts and enhances the melt electrical conductivity in a way that differs from electrical conduction in the bulk water. The speciation of the water component varies considerably from the bulk water structure as well. Water is dissolved in melts mostly as hydroxyls at low pressure and as –O–H–O–, –O–H–O–H– and other extended species with increasing pressure. On the other hand, the pure water behaves as a molecular fluid below 15 GPa, gradually becoming a dissociated fluid with further compression. On the basis of modeled density and conductivity results, we suggest that partial melts containing a few percent of water may be gravitationally trapped both above and below the upper mantle-transition region. Moreover, such hydrous melts can give rise to detectable electrical conductance by means of electromagnetic sounding observations.

Surge in a Low-Speed Radial Compressor

1998 ◽  
Author(s):  
Corine Meuleman ◽  
Frank Willems ◽  
Rick de Lange ◽  
Bram de Jager
Keyword(s):  
Flow Rate ◽  
Pressure Rise ◽  
Flow Coefficient ◽  
Lumped Parameter Model ◽  
Pressure Oscillations ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Radial Compressor ◽  
Low Speed ◽  
Lumped Parameter

Surge is measured in a low-speed radial compressor with a vaned diffuser. For this system, the flow coefficient at surge is determined. This coefficient is a measure for the inducer inlet flow angle and is found to increase with increasing rotational speed. Moreover, the frequency and amplitude of the pressure oscillations during fully-developed surge are compared with results obtained with the Greitzer lumped parameter model. The measured surge frequency increases when the compressor mass flow is throttled to a smaller flow rate. Simulations show that the Greitzer model describes this relation reasonably well except for low rotational speeds. The predicted amplitude of the pressure rise oscillations is approximately two times too small when deep surge is met in the simulations. For classic surge, the agreement is worse. The amplitude is found to depend strongly on the shape of the compressor and throttle characteristic, which are not accurately known.

scholarly journals Introduction of an Universal Scale-Up Method for the Efficiency of Axial and Centrifugal Fans

2014 ◽  
Author(s):  
Peter F. Pelz ◽  
Stefan S. Stonjek
Keyword(s):  
Test Data ◽  
Scale Up ◽  
Pressure Rise ◽  
Flow Coefficient ◽  
Total Efficiency ◽  
Scaling Method ◽  
Centrifugal Fans ◽  
Axial Fans ◽  
Definition Of ◽  
Acceptance Tests

Acceptance tests on large fans to prove the performance (efficiency and total pressure rise) to the customer are expensive and sometimes even impossible to perform. Hence there is a need for the manufacturer to reliably predict the performance of fans from measurements on down-scaled test fans. The commonly used scale-up formulas give satisfactorily results only near the design point, where inertia losses are small in comparison to frictional losses. At part- and overload the inertia losses are dominant and the scale-up formulas used so far fail. In 2013 Pelz and Stonjek introduced a new scaling method which fullfills the demands ( [1], [2]). This method considers the influence of surface roughness and geometric variations on the performance. It consists basically of two steps: Initially, the efficiency is scaled. Efficiency scaling is derived analytically from the definition of the total efficiency. With the total derivative it can be shown that the change of friction coefficient is inversely proportional to the change of efficiency of a fan. The second step is shifting the performance characteristic to a higher value of flow coefficient. It is the task of this work to improve the scaling method which was previously introduced by Pelz and Stonjek by treating the rotor/impeller and volute/stator separately. The validation of the improved scale-up method is performed with test data from two axial fans with a diameter of 1000 mm/250mm and three centrifugal fans with 2240mm/896mm/224mm diameter. The predicted performance characteristics show a good agreement to test data.

scholarly journals Testing for ion-mediated enhancement of the hydraulic conductance of the leaf xylem in diverse angiosperms

2017 ◽  
Vol 4 ◽  
pp. e004 ◽  
Author(s):  
Christine Scoffoni ◽  
Grace John ◽  
Herve Cochard ◽  
Lawren Sack
Keyword(s):  
Water Solution ◽  
Pure Water ◽  
Xylem Sap ◽  
Hydraulic Conductance ◽  
Membrane Pores ◽  
Whole Plant ◽  
Pit Membrane ◽  
Major Bottleneck ◽  
The Difference ◽  
Xylem Conduits

Replacing ultra-pure water solution with ion solution closer to the composition of natural xylem sap increases stem hydraulic conductance by up to 58%, likely due to changes in electroviscosity in the pit membrane pores. This effect has been proposed to contribute to the control of plant hydraulic and stomatal conductance and potentially to influence on carbon balance during dehydration. However, this effect has never been directly tested for leaf xylem, which constitutes a major bottleneck in the whole plant. We tested for an ion-mediated increase in the hydraulic conductance of the leaf xylem (Kx) for seven species diverse in phylogeny and drought tolerance. Across species, no significant changes in Kx were observed between 0 and 15 mM KCl. We further tested for an effect of ion solution during measurements of Kx vulnerability to dehydration in Quercus agrifolia and found no significant impact. These results for leaf xylem contrast with the often strong ion effect reported for stems, and we suggest several hypotheses to account for the difference, relating to the structure of xylem conduits across vein orders, and the ultrastructure of leaf xylem pores. A negligible ion response in leaves would weaken xylem sap ion-mediated control of plant hydraulic conductance, facilitating modeling of whole plant hydraulic behavior and its influence on productivity.

scholarly journals ANALISA PERHITUNGAN DAYA POMPA SENTRIFUGAL DI GEDUNG UNIVERSITAS 17AGUSTUS 1945 JAKARTA

2019 ◽  
Vol 4 (1) ◽  
pp. 7-14
Author(s):  
M Fajri Hidayat ◽  
Nor Fajri
Keyword(s):  
Pump Power ◽  
Centrifugal Pump ◽  
Water Requirement ◽  
Clean Water ◽  
Pump Head ◽  
Pump Shaft ◽  
Specific Speed

AbstrakPompa adalah suatu alat atau mesin untuk memindahkan cairan dari satu tempat ketempat lain melalui suatu media perpipaan dengan cara menambahkan energi pada cairan yang dipindahkan dan berlangsung secara terus menerus. Pompa yang digunakan dalam analisa ini yaitu Pompa Sentrifugal yang terdapat di gedung Universitas 17 Agustus 1945 Jakarta. Tujuan dari analisa ini yaitu untuk mengetahui kebutuhan air pada gedung Universitas 17 Agustus 1945 Jakarta. Kebutuhan air pada gedung Universitas 17 Agustus 1945 Jakarta dihitung berdasarkan luas lantai gedung dan pemakaian setiap dosen, karyawan, mahasiswa, dan rektorat di Universitas 17 Agustus 1945 Jakarta. Hasil analisa di dapatkan total kebutuhan air bersih pada gedung Universitas 17 Agustus 1945 Jakarta adalah 1.7910 Liter/hari. Kapasitas pompa sebesar 0.06 m3/s. Head total pompa sebesar 31.99 m. Putaran poros pompa yaitu 1500 rpm. Daya pompa sebesar 0.817 kW. Kecepatan spesifik sebesar 48.51 rpm. Dari hasil analisa dapat dinyatakan bahwa Pompa Sentrifugal yang berada di gedung Universitas 17 Agustus 1945 Jakarta sudah layak untuk digunakan. Kata Kunci : Kebutuhan air, kapasitas pompa, pompa sentrifugal Abstract          A pump is a device or a machine to move liquids from one place to another via a piping medium by adding energy to the fluid that is moved and continuous. The pump used in this analysis is the Centrifugal Pump contained in the building University 17 August 1945 Jakarta. The purpose of this analysis is to determine the needs of water in the building University 17 August 1945 Jakarta. Water requirement at University building August 17, 1945 Jakarta is calculated based on building floor and usage of every lecturer, staff, student, and rectorate in University 17 August 1945 Jakarta. The result of the analysis in obtaining the total clean water requirement at the building University 17 August 1945 Jakarta is 1.7910 Liter / day. The pump capacity is 0.06 m3 / s. The total pump head is 31.99 m. The rotation of the pump shaft is 1500 rpm. The pump power is 0.817 kW. Specific speed of 48.51 rpm. The results of the analysis can be stated that the Centrifugal Pump located in the building University 17 August 1945 Jakarta is feasible to use. Keywords : Water requirement, pump capacity, centrifugal pump

On Reliable Performance Prediction of Axial Turbomachines

2010 ◽  
Author(s):  
Michael Heß ◽  
Peter F. Pelz
Keyword(s):  
Performance Prediction ◽  
Pressure Coefficient ◽  
Scale Up ◽  
Pressure Rise ◽  
Reynolds Numbers ◽  
Flow Coefficient ◽  
Factor V ◽  
Relative Roughness ◽  
Reliable Performance ◽  
Reliable Scale

There is a need to reliably predict the performance (efficiency and total pressure rise) of axial turbomachines from model tests for different load ranges. The commonly used scale-up formulas are not able to reliably predict the performance, especially beyond the design point. Furthermore these formulas do not regard changes in relative roughness as they usually occur in practice. An improved scale-up formula is proposed which achieves not only the reliable scale-up of efficiency, but also the scale-up of the pressure coefficient. It is motivated from measurements on two geometric similar axial model fans with a diameter of 1000 mm respectively 250 mm at different rotational speeds, hence Reynolds numbers. By bonding grains of sand to the impeller the influence of relative roughness was investigated. For applying the formula to different load ranges a factor V is introduced that depends on the quotient of effective flow coefficient to optimal flow coefficient.

The Effects Produced by a Butterfly Valve in a Hydraulic Closed Circuit

2015 ◽  
Vol 811 ◽  
pp. 117-121
Author(s):  
Lucian Mândrea ◽  
Corina Cipu ◽  
Corina Băbuţanu ◽  
Gabriela Oprina
Keyword(s):  
Flow Rate ◽  
Pressure Loss ◽  
Volumetric Flow Rate ◽  
Water Velocity ◽  
Flow Coefficient ◽  
Closed Circuit ◽  
Butterfly Valve ◽  
Local Pressure ◽  
Pressure Transducers ◽  
Average Water

The paper presents the operation of a hydraulic closed circuit equipped with a butterfly valve which can close with a step of 10o. Using four pressure transducers and one temperature transducer, the authors determined the volumetric flow rate, the average water velocity and the local pressure loss in the butterfly valve, the flow coefficient Kv and also the incipient cavitation coefficient. Recommendations for the disposal of the butterfly valve are made and conclusions are obtained regarding the range of opening degrees in which the butterfly valve is better to be used.

Hydrometallurgical thermodynamics. I. Effect of sulfate ion-pairing and ion-solvation on the copper-iron redox equilibrium in aqueous acetonitrile

1983 ◽  
Vol 36 (9) ◽  
pp. 1687 ◽  
Author(s):  
BW Clare ◽  
P Singh ◽  
P Mangano ◽  
AJ Parker ◽  
DM Muir
Keyword(s):  
Water Solution ◽  
Pure Water ◽  
Ion Pairing ◽  
Ion Solvation ◽  
Sulfate Ion ◽  
Redox Equilibrium ◽  
Small Shift ◽  
Enthalpy Changes ◽  
The Right ◽  
Iron Redox

The copper-iron redox equilibrium is shifted to the right CuII+FeII↔CuI+FeIII by strong ion-pairing of sulfate ion with FeIII and by specific solvation of CuI with acetonitrile. The equilibrium constant has been measured by direct e.m.f. and spectroscopic methods between pH 0-2 and found to be about 107 higher for practical solutions of sulfates in acetonitrile/water than that calculated for perchlorates in pure water. Enthalpies and free energies of transfer of these ions from water to acetonitrile/water show that the shift in equilibrium to Cul+FeIII in acetonitrile/water solution is strongly favoured by enthalpy changes associated with copper(I)-acetonitrile ion-solvation. Ion-pairing of sulfate ion with iron(III) results in an increase in entropy and a small shift of the equilibrium to the right.

Sign in / Sign up

Export Citation Format

Share Document