Structure of Turbulent Flows Over Forward Facing Steps With Adverse Pressure Gradient

2016 ◽  
Vol 138 (11) ◽  
Author(s):  
Hassan Iftekhar ◽  
Martin Agelin-Chaab
Keyword(s):  
Reynolds Number ◽  
Pressure Gradient ◽  
Turbulent Flows ◽  
Large Scale ◽  
Adverse Pressure Gradient ◽  
Reynolds Numbers ◽  
Step Height ◽  
Reattachment Length ◽  
Mean Velocity ◽  
The Mean

This paper reports an experimental study on the effects of adverse pressure gradient (APG) and Reynolds number on turbulent flows over a forward facing step (FFS) by employing three APGs and three Reynolds numbers. A particle image velocimetry (PIV) technique was used to conduct velocity measurements at several locations downstream, and the flow statistics up to 68 step heights are reported. The step height was maintained at 6 mm, and the Reynolds numbers based on the step height and freestream mean velocity were 1600, 3200, and 4800. The mean reattachment length increases with the increase in Reynolds number without the APG whereas the mean reattachment length remains constant for increasing APG. The proper orthogonal decomposition (POD) results confirmed that higher Reynolds numbers caused the large-scale structures to be more defined and organized close to the step surface.

The Structure of Forward Facing Step Flows in Adverse Pressure Gradient

2014 ◽  
Author(s):  
Weijie Shao ◽  
Martin Agelin-Chaab
Keyword(s):  
Pressure Gradient ◽  
Turbulent Flows ◽  
Decomposition Analysis ◽  
Adverse Pressure Gradient ◽  
Quality Data ◽  
Reattachment Length ◽  
Mean Flow ◽  
Particle Image Velocimetry Technique ◽  
The Mean ◽  
Forward Facing Step

This paper reports an investigation of the effects of adverse pressure gradient on turbulent flows over forward facing step. Three adverse pressure gradients were created for this study using diverging channels. A particle image velocimetry technique was used to conduct measurements in the streamwise-wall-normal (x-y) planes at the mid-plane of test section at several locations downstream to 68 step heights. A Reynolds number of Reh = 4800 and δ/h = 4.7 were employed, where h is the mean step height and δ is the approach boundary layer thickness. The results include the mean flow and turbulence quantities as well as proper orthogonal decomposition analysis. The mean reattachment length obtained indicates that the adverse pressure gradient created in this study does not have significant effects on the reattachment length. The triple velocity correlations imply that there is negative transport of turbulence kinetic energy close to the wall and positive transport away from the wall. In addition to the physical insight, the high quality data reported are useful for assessing the ability of turbulence models to reproduce the behaviour of complex flows.

scholarly journals A predictive inner–outer model for streamwise turbulence statistics in wall-bounded flows

2011 ◽  
Vol 681 ◽  
pp. 537-566 ◽  
Author(s):  
ROMAIN MATHIS ◽  
NICHOLAS HUTCHINS ◽  
IVAN MARUSIC
Keyword(s):  
Pressure Gradient ◽  
Turbulent Flows ◽  
Large Scale ◽  
Adverse Pressure Gradient ◽  
Reynolds Numbers ◽  
Streamwise Velocity ◽  
Gradient Flows ◽  
Streamwise Pressure Gradient ◽  
Logarithmic Region ◽  
Inner Region

A model is proposed with which the statistics of the fluctuating streamwise velocity in the inner region of wall-bounded turbulent flows are predicted from a measured large-scale velocity signature from an outer position in the logarithmic region of the flow. Results, including spectra and all moments up to sixth order, are shown and compared to experimental data for zero-pressure-gradient flows over a large range of Reynolds numbers. The model uses universal time-series and constants that were empirically determined from zero-pressure-gradient boundary layer data. In order to test the applicability of these for other flows, the model is also applied to channel, pipe and adverse-pressure-gradient flows. The results support the concept of a universal inner region that is modified through a modulation and superposition of the large-scale outer motions, which are specific to the geometry or imposed streamwise pressure gradient acting on the flow.

Turbulent Flows Over Forward Facing Steps With Surface Roughness

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Weijie Shao ◽  
Martin Agelin-Chaab
Keyword(s):  
Surface Roughness ◽  
Turbulent Flows ◽  
Large Scale ◽  
Reynolds Numbers ◽  
Step Height ◽  
Mean Velocity ◽  
Surface Conditions ◽  
Large Scale Structures ◽  
Image Velocimetry ◽  
Proper Orthogonal

This paper reports an investigation of the effects of surface conditions of forward-facing steps (FFS) on turbulent flows. Three surface conditions including one smooth step and two rough step surfaces created using sandpapers were studied. A particle image velocimetry (PIV) technique was used to conduct velocity measurements at several locations downstream, and the statistics up to 60 step heights are reported. The step height was maintained at 6 mm, and three Reynolds numbers of Reh = 1600, 3200, and 4800, where Reh is based on the step height and freestream mean velocity, were studied. The results indicate that the reattachment length of a FFS increases with Reynolds number but decreases with increasing surface roughness. The proper orthogonal decomposition (POD) results showed the step roughness affects even the large-scale structures.

The structure of a highly decelerated axisymmetric turbulent boundary layer

2021 ◽  
Vol 929 ◽  
Author(s):  
N. Agastya Balantrapu ◽  
Christopher Hickling ◽  
W. Nathan Alexander ◽  
William Devenport
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Shear Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Large Scale ◽  
Convection Velocity ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean

Experiments were performed over a body of revolution at a length-based Reynolds number of 1.9 million. While the lateral curvature parameters are moderate ( $\delta /r_s < 2, r_s^+>500$ , where $\delta$ is the boundary layer thickness and r s is the radius of curvature), the pressure gradient is increasingly adverse ( $\beta _{C} \in [5 \text {--} 18]$ where $\beta_{C}$ is Clauser’s pressure gradient parameter), representative of vehicle-relevant conditions. The mean flow in the outer regions of this fully attached boundary layer displays some properties of a free-shear layer, with the mean-velocity and turbulence intensity profiles attaining self-similarity with the ‘embedded shear layer’ scaling (Schatzman & Thomas, J. Fluid Mech., vol. 815, 2017, pp. 592–642). Spectral analysis of the streamwise turbulence revealed that, as the mean flow decelerates, the large-scale motions energize across the boundary layer, growing proportionally with the boundary layer thickness. When scaled with the shear layer parameters, the distribution of the energy in the low-frequency region is approximately self-similar, emphasizing the role of the embedded shear layer in the large-scale motions. The correlation structure of the boundary layer is discussed at length to supply information towards the development of turbulence and aeroacoustic models. One major finding is that the estimation of integral turbulence length scales from single-point measurements, via Taylor's hypothesis, requires significant corrections to the convection velocity in the inner 50 % of the boundary layer. The apparent convection velocity (estimated from the ratio of integral length scale to the time scale), is approximately 40 % greater than the local mean velocity, suggesting the turbulence is convected much faster than previously thought. Closer to the wall even higher corrections are required.

Pressure gradient effects on the large-scale structure of turbulent boundary layers

2013 ◽  
Vol 715 ◽  
pp. 477-498 ◽  
Author(s):  
Zambri Harun ◽  
Jason P. Monty ◽  
Romain Mathis ◽  
Ivan Marusic
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Amplitude Modulation ◽  
Large Scale ◽  
Outer Region ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Small Scale

AbstractResearch into high-Reynolds-number turbulent boundary layers in recent years has brought about a renewed interest in the larger-scale structures. It is now known that these structures emerge more prominently in the outer region not only due to increased Reynolds number (Metzger & Klewicki, Phys. Fluids, vol. 13(3), 2001, pp. 692–701; Hutchins & Marusic, J. Fluid Mech., vol. 579, 2007, pp. 1–28), but also when a boundary layer is exposed to an adverse pressure gradient (Bradshaw, J. Fluid Mech., vol. 29, 1967, pp. 625–645; Lee & Sung, J. Fluid Mech., vol. 639, 2009, pp. 101–131). The latter case has not received as much attention in the literature. As such, this work investigates the modification of the large-scale features of boundary layers subjected to zero, adverse and favourable pressure gradients. It is first shown that the mean velocities, turbulence intensities and turbulence production are significantly different in the outer region across the three cases. Spectral and scale decomposition analyses confirm that the large scales are more energized throughout the entire adverse pressure gradient boundary layer, especially in the outer region. Although more energetic, there is a similar spectral distribution of energy in the wake region, implying the geometrical structure of the outer layer remains universal in all cases. Comparisons are also made of the amplitude modulation of small scales by the large-scale motions for the three pressure gradient cases. The wall-normal location of the zero-crossing of small-scale amplitude modulation is found to increase with increasing pressure gradient, yet this location continues to coincide with the large-scale energetic peak wall-normal location (as has been observed in zero pressure gradient boundary layers). The amplitude modulation effect is found to increase as pressure gradient is increased from favourable to adverse.

scholarly journals Natural logarithms

2013 ◽  
Vol 718 ◽  
pp. 1-4 ◽  
Author(s):  
B. J. McKeon
Keyword(s):  
Turbulent Flows ◽  
Reynolds Numbers ◽  
Streamwise Velocity ◽  
Wall Turbulence ◽  
Significant Advance ◽  
Mean Velocity ◽  
Velocity Fluctuations ◽  
Logarithmic Scaling ◽  
The Mean ◽  
High Reynolds

AbstractMarusic et al. (J. Fluid Mech., vol. 716, 2013, R3) show the first clear evidence of universal logarithmic scaling emerging naturally (and simultaneously) in the mean velocity and the intensity of the streamwise velocity fluctuations about that mean in canonical turbulent flows near walls. These observations represent a significant advance in understanding of the behaviour of wall turbulence at high Reynolds number, but perhaps the most exciting implication of the experimental results lies in the agreement with the predictions of such scaling from a model introduced by Townsend (J. Fluid Mech., vol. 11, 1961, pp. 97–120), commonly termed the attached eddy hypothesis. The elegantly simple, yet powerful, study by Marusic et al. should spark further investigation of the behaviour of all fluctuating velocity components at high Reynolds numbers and the outstanding predictions of the attached eddy hypothesis.

Experimental Investigation of a Turbulent Boundary Layer Subjected to an Adverse Pressure Gradient

2011 ◽  
Author(s):  
Takanori Nakamura ◽  
Takatsugu Kameda ◽  
Shinsuke Mochizuki
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Friction Velocity ◽  
Adverse Pressure Gradient ◽  
Turbulent Intensity ◽  
Mean Velocity ◽  
Law Of The Wall ◽  
Velocity Scale ◽  
The Mean ◽  
The Law

Experiments were performed to investigate the effect of an adverse pressure gradient on the mean velocity and turbulent intensity profiles for an equilibrium boundary layer. The equilibrium boundary layer, which makes self-similar profiles, was constructed using a power law distribution of free stream velocity. The exponent of the law was adjusted to −0.188. The wall shear stress was measured with a drag balance by a floating element. The investigation of the law of the wall and the similarity of the streamwise turbulent intensity profile was made using both a friction velocity and new proposed velocity scale. The velocity scale is derived from the boundary layer equation. The mean velocity gradient profile normalized with the height and the new velocity scale exists the region where the value is almost constant. The turbulent intensity profiles normalized with the friction velocity strongly depend on the nondimensional pressure gradient near the wall. However, by mean of the local velocity scale, the profiles might be achieved to be similar with that of a zero pressure gradient.

LDV and PIV Velocity Results in a Thermosiphon

2003 ◽  
Author(s):  
J. Kulman ◽  
D. Gray ◽  
S. Sivanagere ◽  
S. Guffey
Keyword(s):  
Large Scale ◽  
Single Phase ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Laser Doppler Velocimeter ◽  
Mean Velocity ◽  
Developed Turbulence ◽  
The Mean ◽  
Good Agreement

Heat transfer and flow characteristics have been determined for a single-phase rectangular loop thermosiphon. The plane of the loop was vertical, and tests were performed with in-plane tilt angles ranging from 3.6° CW to 4.2° CCW. Velocity profiles were measured in one vertical leg of the loop using both a single-component Laser Doppler Velocimeter (LDV), and a commercial Particle Image Velocimeter (PIV) system. The LDV data and PIV data were found to be in good agreement. The measured average velocities were approximately 2–2.5 cm/s at an average heating rate of 70 W, and were independent of tilt angle. Significant RMS fluctuations of 10–20% of the mean velocity were observed in the test section, in spite of the laminar or transitional Reynolds numbers (order of 700, based on the hydraulic diameter). These fluctuations have been attributed to vortex shedding from the upstream temperature probes and mitre bends, rather than to fully developed turbulence. Animations of the PIV data clearly show these large scale unsteady flow patterns. Multiple steady state flow patterns were not observed.

scholarly journals Reynolds number dependence of mean flow structure in square duct turbulence

2010 ◽  
Vol 644 ◽  
pp. 107-122 ◽  
Author(s):  
ALFREDO PINELLI ◽  
MARKUS UHLMANN ◽  
ATSUSHI SEKIMOTO ◽  
GENTA KAWAHARA
Keyword(s):  
Reynolds Number ◽  
Secondary Flow ◽  
Buffer Layer ◽  
Turbulent Flows ◽  
Reynolds Numbers ◽  
The Other ◽  
Streamwise Vorticity ◽  
Square Duct ◽  
Layer Structures ◽  
The Mean

We have performed direct numerical simulations of turbulent flows in a square duct considering a range of Reynolds numbers spanning from a marginal state up to fully developed turbulent states at low Reynolds numbers. The main motivation stems from the relatively poor knowledge about the basic physical mechanisms that are responsible for one of the most outstanding features of this class of turbulent flows: Prandtl's secondary motion of the second kind. In particular, the focus is upon the role of flow structures in its generation and characterization when increasing the Reynolds number. We present a two-fold scenario. On the one hand, buffer layer structures determine the distribution of mean streamwise vorticity. On the other hand, the shape and the quantitative character of the mean secondary flow, defined through the mean cross-stream function, are influenced by motions taking place at larger scales. It is shown that high velocity streaks are preferentially located in the corner region (e.g. less than 50 wall units apart from a sidewall), flanked by low velocity ones. These locations are determined by the positioning of quasi-streamwise vortices with a preferential sign of rotation in agreement with the above described velocity streaks' positions. This preferential arrangement of the classical buffer layer structures determines the pattern of the mean streamwise vorticity that approaches the corners with increasing Reynolds number. On the other hand, the centre of the mean secondary flow, defined as the position of the extrema of the mean cross-stream function (computed using the mean streamwise vorticity), remains at a constant location departing from the mean streamwise vorticity field for larger Reynolds numbers, i.e. it scales in outer units. This paper also presents a detailed validation of the numerical technique including a comparison of the numerical results with data obtained from a companion experiment.

A supersonic turbulent boundary layer in an adverse pressure gradient

1990 ◽  
Vol 211 ◽  
pp. 285-307 ◽  
Author(s):  
Emerick M. Fernando ◽  
Alexander J. Smits
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Pressure Distribution ◽  
Large Scale ◽  
Adverse Pressure Gradient ◽  
Large Scale Structures ◽  
Streamline Curvature ◽  
The Mean ◽  
Scale Structures

This investigation describes the effects of an adverse pressure gradient on a flat plate supersonic turbulent boundary layer (Mf ≈ 2.9, βx ≈ 5.8, Reθ, ref ≈ 75600). Single normal hot wires and crossed wires were used to study the Reynolds stress behaviour, and the features of the large-scale structures in the boundary layer were investigated by measuring space–time correlations in the normal and spanwise directions. Both the mean flow and the turbulence were strongly affected by the pressure gradient. However, the turbulent stress ratios showed much less variation than the stresses, and the essential nature of the large-scale structures was unaffected by the pressure gradient. The wall pressure distribution in the current experiment was designed to match the pressure distribution on a previously studied curved-wall model where streamline curvature acted in combination with bulk compression. The addition of streamline curvature affects the turbulence strongly, although its influence on the mean velocity field is less pronounced and the modifications to the skin-friction distribution seem to follow the empirical correlations developed by Bradshaw (1974) reasonably well.

Sign in / Sign up

Export Citation Format

Share Document