Application of Dynamic ϕ–T Map: Analysis on a Natural Gas/Diesel Fueled RCCI Engine

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Jing Li ◽  
Wenming Yang ◽  
Hui An ◽  
Dezhi Zhou ◽  
Markus Kraft
Keyword(s):  
Natural Gas ◽  
Soot Formation ◽  
Combustion Process ◽  
Diesel Oil ◽  
Chemical Mechanism ◽  
Low Temperature Combustion ◽  
Injection Duration ◽  
Start Of Injection ◽  
Temperature Combustion ◽  
Map Analysis

In this study, dynamic ϕ–T map analysis was applied to a reactivity controlled compression ignition (RCCI) engine fueled with natural gas (NG) and diesel. The combustion process of the engine was simulated by coupled kiva4-chemkin with a diesel oil surrogate (DOS) chemical mechanism. The ϕ–T maps were constructed by the mole fractions of soot and NO obtained from senkin and ϕ–T conditions from engine simulations. Five parameters, namely, NG fraction, first start of injection (SOI) timing, second SOI timing, second injection duration, and exhaust gas recirculation (EGR) rate, were varied in certain ranges individually, and the ϕ–T maps were compared and analyzed under various conditions. The results revealed how the five parameters would shift the ϕ–T conditions and influence the soot–NO contour. Among the factors, EGR rate could limit the highest temperature due to its dilute effect, hence maintaining RCCI combustion within low-temperature combustion (LTC) region. The second significant parameter is the premixed NG fraction. It could set the lowest temperature; moreover, the tendency of soot formation can be mitigated due to the lessened fuel impingement and the absence of C–C bond. Finally, the region of RCCI combustion was added to the commonly known ϕ–T map diagram.

Application of Dynamic Φ-T Map: Analysis on a Natural Gas/Diesel Fueled RCCI Engine

2015 ◽  
Author(s):  
Jing Li ◽  
Wenming Yang ◽  
Hui An ◽  
Dezhi Zhou ◽  
Markus Kraft
Keyword(s):  
Natural Gas ◽  
Soot Formation ◽  
Combustion Process ◽  
Diesel Oil ◽  
Chemical Mechanism ◽  
Injection Timing ◽  
Low Temperature Combustion ◽  
Compression Ignition Engine ◽  
Injection Duration ◽  
Map Analysis

In this study, dynamic ϕ-T map analysis was applied to an RCCI (reactivity controlled compression ignition) engine fueled with NG (natural gas) and diesel. The combustion process of the engine was simulated by coupled KIVA4-CHEMKIN with a DOS (diesel oil surrogate) chemical mechanism. The ϕ-T maps were constructed by the mole fractions of soot and NO obtained from SENKIN and ϕ-T conditions from engine simulations. Five parameters, namely NG fraction, 1st SOI (start of injection) timing, 2nd SOI timing, 2nd injection duration and EGR (exhaust gas recirculation) rate were varied in certain ranges individually, and the ϕ-T maps were compared and analyzed under various conditions. The results revealed how the five parameters would shift the ϕ-T conditions and influence the soot-NO contour. Among the factors, EGR rate could limit the highest temperature due to its dilute effect, hence maintaining RCCI combustion within LTC (low temperature combustion) region. The second significant parameter is the premixed NG fraction. It could set the lowest temperature; moreover, the tendency of soot formation can be mitigated due to the lessened fuel impingement and the absence of C-C bond. Finally, the region of RCCI combustion was added to the commonly known ϕ-T map diagram.

Experimental Study on Low Temperature Combustion Dual Fuel Biodiesel/Natural Gas Engine

2015 ◽  
Author(s):  
A. Gharehghani ◽  
M. Mirsalim ◽  
A. Jazayeri ◽  
R. Hosseini
Keyword(s):  
Diesel Engine ◽  
Low Temperature ◽  
Natural Gas ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Dual Fuel ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Temperature Combustion

Low Temperature combustion (LTC) strategies are capable of simultaneous reduction in NOx and particulate matter (PM) emissions. However, this combustion process generally leads to higher HC and CO emissions together with more cyclic variation (unstable combustion) especially at light engine loads. These emissions could drastically be reduced using certain alternative fuels like natural gas and biodiesel in LTC or PCI combustion engines. In the present research, a single cylinder compression ignition engine has been modified to operate in dual fuel mode with natural gas injection into the intake manifold as the main fuel and biodiesel as the pilot fuel to ignite the gas/air mixture. The combustion characteristics, engine performance and exhaust emissions of the reactivity controlled compression ignition (RCCI) dual fueled CNG/biodiesel engine are investigated and compared with the conventional diesel engine mode at various load conditions. The analysis of the results revealed that biodiesel as the high reactivity fuel in RCCI mode leads to higher in-cylinder pressure together with shorter heat release rate duration, compared to the common diesel engine. Experimental results indicated that combining the low temperature combustion concept and alternative fuels (e.g. biodiesel and naturals gas) causes lower levels of unburned hydrocarbon (UHC) and carbon monoxide (CO) as well as nitrogen oxide (NOx) emissions.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

Exploring the Effects of Piston Bowl Geometry and Injector Included Angle On Dual-Fuel and Single-Fuel RCCI

2021 ◽  
Author(s):  
Deivanayagam Hariharan ◽  
Mozhgan Rahimi Boldaji ◽  
Ziming Yan ◽  
Brian Gainey ◽  
Benjamin Lawler
Keyword(s):  
Thermal Efficiency ◽  
Lower Surface ◽  
Combustion Efficiency ◽  
Low Temperature Combustion ◽  
Included Angle ◽  
Piston Bowl ◽  
Start Of Injection ◽  
Lower Reactivity ◽  
Secondary Fuel ◽  
Temperature Combustion

Abstract Reactivity Control Compression Ignition (RCCI) is a Low-Temperature Combustion (LTC) technique that have been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel is generated from the primary fuel through CPOX reformation. After studying three different fuels, diesel was found to be the best candidate for the reformation process, where the reformed gaseous fuel (with lower reactivity) was used as the secondary fuel and the parent diesel fuel (with higher reactivity) was used as the primary fuel. Previously, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were studied in detail. In this study, the effect of piston profile and the injector included angles were experimentally studied using both conventional fuel pairs and reformate RCCI. A validated CFD model was also used for a better understanding of the experimental trends. Comparing a re-entrant bowl piston with a shallow bowl piston, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree and 60-degree included angle, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing) as the fuel spray targets better region of the cylinder.

Modelling of Soot Formation and Experimental Study for Different Octane Number Fuels in Dual Fuel Combustion Engine With Diesel

2020 ◽  
Author(s):  
M. Krishnamoorthi ◽  
S. Sreedhara ◽  
Pavan Prakash Duvvuri
Keyword(s):  
Particle Size ◽  
Soot Formation ◽  
Combustion Engine ◽  
Combustion Process ◽  
Dual Fuel ◽  
Nox Emissions ◽  
Low Temperature Combustion ◽  
Oxides Of Nitrogen ◽  
Condensation Mode ◽  
Test Engine

Abstract This work investigates the effects of low reactivity fuel (LRF) on reactivity controlled compression ignition (RCCI) engine with fossil diesel. RCCI mode of combustion is a low temperature combustion (LTC) strategy which reduces both oxides of nitrogen (NOx) and soot emissions simultaneously. Syngas and methanol can be obtained from renewable biological resources and conventional coal. LRF (methanol, syngas and gasoline) has been supplied to the engine along with intake air and diesel is injected to initiate the combustion process. Test engine has been operated for different dual fuel modes at constant engine speed (1500 rpm) and load (80%). Closed cycle combustion simulations have been performed to complement the experimental results and in-cylinder dynamics. Particle size mimic (PSM) model has been used to investigate the soot particle number and mass-size distributions and mean particle size. Results confirmed that maximum gross indicated thermal efficiency (38%) has been observed in gasoline/diesel dual fuel mode. Compared to gasoline/diesel dual fuel mode, about 74% and 86%, lower soot and NOx emissions have been observed for methanol/diesel dual fuel mode, while about 46% and 52% lower soot and NOx emissions have been found in syngas/diesel mode. About 53% higher carbon monoxide emission has been observed for syngas/diesel case as compared to gasoline/diesel case. Predictions from soot modelling reveal that condensation mode, surface growth mode and nucleation mode particles are dominant in methanol, syngas and gasoline/diesel dual fuel modes respectively. Bigger primary soot particles (diameter > 35 nm, nanometre) have been observed for methanol/diesel mode and the gasoline/diesel mode shows a smaller size of primary particles.

Characteristics of Diesel Spray With Varying Injection Rate

2019 ◽  
Author(s):  
Intarat Naruemon ◽  
Long Liu ◽  
Dai Liu ◽  
Xiuzhen Ma
Keyword(s):  
Ignition Time ◽  
Fuel Mixture ◽  
Injection Rate ◽  
Diesel Spray ◽  
Low Temperature Combustion ◽  
Multiple Injection ◽  
Injection Duration ◽  
Injection Process ◽  
Temperature Combustion ◽  
Combustion Processes

Abstract Multiple-injection is an effective injection strategy in order to control the advanced combustion processes in diesel engines. However, because of the multiple-injection application, cause the duration of each injection is shortened, such as the pilot injection and post-injection. The short injection duration results in a very short quasi-steady injection process so that the ramping-up and ramping-down injection processes occupied a much larger scale during the injection. As a result, this circumstance of the spray evolution not been fully understood. To investigate the diesel spray propagation with varying injection rate, visual experiments and numerical simulation analyses on diesel spray were performed. The penetrations of diesel sprays with short injection duration were obtained by reflected shadowgraphy in a combustion chamber’s constant-volume with the multi-hole injector. The diesel spray with varying injection rates was modeled by using CONVERGE CFD software and the model was calibrated and validated by the experimental data. Then diagnosed the spray characteristics including spray penetration, Sauter means diameter, as well as fuel concentration distribution, were analyzed with different injection quantities and injection rate shapes. The spray mixing analysis included that after the end-of-injection in order to consider the low-temperature combustion phenomenon. The shape of the improved injection rate in the fuel mixture considered in the case of injection ending before or after the ignition time was summarized for different conditions.

A Computational Investigation of the Impact of Multiple Injection Strategies on Combustion Efficiency in Diesel-Natural Gas Dual Fuel Low Temperature Combustion Engine

2019 ◽  
Author(s):  
Lorenzo Bartolucci ◽  
Stefano Cordiner ◽  
Vincenzo Mulone ◽  
Sundar R. Krishnan ◽  
Kalyan K. Srinivasan
Keyword(s):  
Experimental Data ◽  
Low Temperature ◽  
Natural Gas ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Single Cylinder ◽  
Temperature Combustion ◽  
The Impact

Abstract Dual fuel diesel-methane low temperature combustion (LTC) has been investigated by various research groups, showing high potential for emissions reduction (especially oxides of nitrogen (NOx) and particulate matter (PM)) without adversely affecting fuel conversion efficiency in comparison with conventional diesel combustion. However, when operated at low load conditions, dual fuel LTC typically exhibit poor combustion efficiencies. This behavior is mainly due to low bulk gas temperatures under lean conditions, resulting in unacceptably high carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. A feasible and rather innovative solution may be to split the pilot injection of liquid fuel into two injection pulses, with the second pilot injection supporting the methane combustion once the process is initiated by the first one. In this work, diesel-methane dual fuel LTC is investigated numerically in a single-cylinder heavy-duty engine operating at 5 bar brake mean effective pressure (BMEP) at 85% and 75% percentage of energy substitution (PES) by methane (taken as a natural gas surrogate). A multidimensional model is first validated in comparison with experimental data obtained on the same single-cylinder engine for early single pilot diesel injection at 310 CAD and 500 bar rail pressure. With the single pilot injection case as baseline, the effects of multiple pilot injections and different rail pressures on combustion emissions are investigated, again showing good agreement with experimental data. Apparent heat release rate and cylinder pressure histories as well as combustion efficiency trends are correctly captured by the numerical model. Results prove that higher rail pressures yield reductions of HC and CO by 90% and 75%, respectively, at the expense of NOx emissions, which increase by ∼30% from baseline. Furthermore, it is shown that post-injection during the expansion stroke does not support the stable development of the combustion front as the combustion process is confined close to the diesel spray core.

Numerical Simulation of a Large Bore Dual Fuel Marine Engine Using Tabulated Detailed Reaction Mechanisms

2019 ◽  
Author(s):  
Sascha Andree ◽  
Dmitry Goryntsev ◽  
Martin Theile ◽  
Björn Henke ◽  
Karsten Schleef ◽  
...  
Keyword(s):  
Reaction Mechanism ◽  
Natural Gas ◽  
Chemical Reaction ◽  
Reaction Mechanisms ◽  
Combustion Process ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Start Of Injection ◽  
Flamelet Generated Manifold ◽  
Dual Fuel Combustion

Abstract The simulation of a diesel natural gas dual fuel combustion process is the topic of this paper. Based on a detailed chemical reaction mechanism, which was applied for such a dual fuel combustion, the complete internal combustion engine process was simulated. Two single fuel combustion reaction mechanisms from literature were merged, to consider the simultaneous reaction paths of diesel and natural gas. N-heptane was chosen as a surrogate for diesel. The chemical reaction mechanisms are solved by applying a tabulation method using the software tool AVL Tabkin™. In combination with a Flamelet Generated Manifold (FGM) combustion model, this leads to a reduction of computational effort compared to a direct solving of the reaction mechanism, because of a decoupling of chemistry and flow calculations. Turbulence was modelled using an unsteady Reynolds-Averaged Navier Stokes (URANS) model. In comparison to conventional combustion models, this approach allows for detailed investigations of the complex ignition process of the dual fuel combustion process. The unexpected inversely proportional relationship between start of injection (SOI) and start of combustion (SOC), a later start of injection makes for an earlier combustion of the main load, is only one of these interesting combustion phenomena, which can now be analyzed in detail. Further investigations are done for different engine load points and multiple pilot injection strategies. The simulation results are confirmed by experimental measurements at a medium speed dual fuel single cylinder research engine.

Modeling Soot Formation Using Reduced PAH Chemistry in n-Heptane Lifted Flames With Application to Low Temperature Combustion

2008 ◽  
Author(s):  
Gokul Vishwanathan ◽  
Rolf D. Reitz
Keyword(s):  
Low Temperature ◽  
Soot Formation ◽  
Numerical Study ◽  
Low Temperature Combustion ◽  
Constant Volume Chamber ◽  
Soot Mass ◽  
Temperature Combustion ◽  
Lifted Flames ◽  
Polycyclic Aromatic ◽  
Species Comparisons

A numerical study of in-cylinder soot formation and oxidation processes in n-heptane lifted flames using various soot inception species has been conducted. In a recent study by the authors, it was found that the soot formation and growth regions in lifted flames were not adequately represented by using acetylene alone as the soot inception species. Comparisons with a conceptual model and available experimental data suggested that the location of soot formation regions could be better represented if polycyclic aromatic hydrocarbon (PAH) species were considered as alternatives to acetylene for soot formation processes. Since the local temperatures are much lower under low temperature combustion (LTC) conditions, it is believed that significant soot mass contribution can be attributed to PAH rather than to acetylene. To quantify and validate the above observations, a reduced n-heptane chemistry mechanism has been extended to include PAH species up to four fused aromatic rings (pyrene). The resulting chemistry mechanism was integrated into the multidimensional CFD code KIVA-CHEMKIN for modeling soot formation in lifted flames in a constant volume chamber. The investigation revealed that a simpler model that only considers up to phenanthrene (three fused rings) as the soot inception species has good possibilities for better soot location predictions. The present work highlights and illustrates the various research challenges toward accurate qualitative and quantitative predictions of soot for new low emission combustion strategies for I.C. engines.

scholarly journals Catalytic partial oxidation reformation of diesel, gasoline, and natural gas for use in low temperature combustion engines

Fuel ◽  
2019 ◽  
Vol 246 ◽  
pp. 295-307 ◽  
Author(s):  
Deivanayagam Hariharan ◽  
Ruinan Yang ◽  
Yingcong Zhou ◽  
Brian Gainey ◽  
Sotirios Mamalis ◽  
...  
Keyword(s):  
Low Temperature ◽  
Natural Gas ◽  
Partial Oxidation ◽  
Catalytic Partial Oxidation ◽  
Low Temperature Combustion ◽  
Combustion Engines ◽  
Temperature Combustion
Sign in / Sign up

Export Citation Format

Share Document