scholarly journals Design and Experimental Validation of a Supersonic Concentric Micro Gas Turbine

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Gabriel Vézina ◽  
Hugo Fortier-Topping ◽  
François Bolduc-Teasdale ◽  
David Rancourt ◽  
Mathieu Picard ◽  
...  
Keyword(s):  
Steady State ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Structural Model ◽  
Structural Integrity ◽  
Turbine Blades ◽  
External Diameter ◽  
Impulse Turbine ◽  
Micro Gas Turbine ◽  
Steady State Operation

This paper presents the design and experimental results of a new micro gas turbine architecture exploiting counterflow within a single supersonic rotor. This new architecture, called the supersonic rim-rotor gas turbine (SRGT), uses a single rotating assembly incorporating a central hub, a supersonic turbine rotor, a supersonic compressor rotor, and a rim-rotor. This SRGT architecture can potentially increase engine power density while significantly reducing manufacturing costs. The paper presents the preliminary design of a 5 kW SRGT prototype having an external diameter of 72.5 mm and rotational speed of 125,000 rpm. The proposed aerodynamic design comprises a single stage supersonic axial compressor, with a normal shock in the stator, and a supersonic impulse turbine. A pressure ratio of 2.75 with a mass flow rate of 130 g/s is predicted using a 1D aerodynamic model in steady state. The proposed combustion chamber uses an annular reverse-flow configuration, using hydrogen as fuel. The analytical design of the combustion chamber is based on a 0D model with three zones (primary, secondary, and dilution), and computational fluid dynamics (CFD) simulations are used to validate the analytical model. The proposed structural design incorporates a unidirectional carbon-fiber-reinforced polymer rim-rotor, and titanium alloy is used for the other rotating components. An analytical structural model and numerical validation predict structural integrity of the engine at steady-state operation up to 1000 K for the turbine blades. Experimentation has resulted in the overall engine performance evaluation. Experimentation also demonstrated a stable hydrogen flame in the combustion chamber and structural integrity of the engine for at least 30 s of steady-state operation at 1000 K.

scholarly journals Investigations on the Blade Vibration of a Radial Inflow Micro Gas Turbine Wheel

2007 ◽  
Vol 2007 ◽  
pp. 1-10 ◽  
Author(s):  
Shijie Guo
Keyword(s):  
Gas Turbine ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Turbine Blades ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Coupled Modes ◽  
Blade Vibration ◽  
Turbine Wheel ◽  
Micro Gas Turbine

This paper demonstrates the investigations on the blade vibration of a radial inflow micro gas turbine wheel. Firstly, the dependence of Young's modulus on temperature was measured since it is a major concern in structure analysis. It is demonstrated that Young's modulus depends on temperature greatly and the dependence should be considered in vibration analysis, but the temperature gradient from the leading edge to the trailing edge of a blade can be ignored by applying the mean temperature. Secondly, turbine blades suffer many excitations during operation, such as pressure fluctuations (unsteady aerodynamic forces), torque fluctuations, and so forth. Meanwhile, they have many kinds of vibration modes, typical ones being blade-hub (disk) coupled modes and blade-shaft (torsional, longitudinal) coupled modes. Model experiments and FEM analysis were conducted to study the coupled vibrations and to identify the modes which are more likely to be excited. The results show that torque fluctuations and uniform pressure fluctuations are more likely to excite resonance of blade-shaft (torsional, longitudinal) coupled modes. Impact excitations and propagating pressure fluctuations are more likely to excite blade-hub (disk) coupled modes.

Research on Matching Characteristics of Ship-Engine-Propeller of COGAG

2021 ◽  
Author(s):  
Zhitao Wang ◽  
Jiayi Ma ◽  
Haichao Yu ◽  
Tielei Li
Keyword(s):  
Steady State ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Research Work ◽  
Simulation Models ◽  
Operating Characteristics ◽  
Modular Modeling ◽  
Steady State Operation ◽  
Pitch Ratio ◽  
Main Engine

Abstract The combined gas turbine and gas turbine power propulsion device (COGAG power propulsion device) is an advanced combined power system, which uses multiple gas turbines as the main engine to drive propellers to propel the ship. COGAG power propulsion device has high power density, excellent stability and maneuverability, it receives more and more attention in the field of ship power at home and abroad. This article takes the COGAG power propulsion device as the research object, uses simulation methods to study its steady-state operating characteristics, and conducts a ship-engine-propeller optimization matching analysis based on economy and maneuverability. The research work carried out in this article is as follows. Firstly, according to the structural relationship between the various components and the system thermal cycle mode of the COGAG power propulsion device, establish the controller, main engine, gear box, clutch, shafting, propeller, ship and other components and simulation models of the system with the modular modeling idea. Secondly, divide the gears according to ship speed. For the four working modes of single-gas turbine with load, dual-gas turbine with load, three-gas turbine with load, and four-gas turbine with load, analysis the ship-engine-propeller optimization matching of the COGAG power propulsion device based on economy and maneuverability, and calculate the best shaft speed and propeller pitch ratio in each gear, so as to obtain the steady-state operation characteristics of the COGAG power propulsion device based on the ship-engine-propeller matching, which provides a basis for determining the target parameters of the dynamic process.

Development of Advanced Combustor for Biomass

2011 ◽  
Author(s):  
Masato Urashima ◽  
Shuichi Torii
Keyword(s):  
Energy Source ◽  
Renewable Energy Source ◽  
Renewable Energy ◽  
Municipal Solid Waste ◽  
Combustion Chamber ◽  
Solid Waste ◽  
Gas Turbine ◽  
The Sun ◽  
Waste Oil ◽  
Micro Gas Turbine

Biomass is a renewable energy source in that the energy that it contains comes from the sun. One of sources of biomass is municipal solid waste. The final goal of the study is to develop the combustor for the micro gas-turbine using the biomass as a fuel. Here, it is very important to remove ashes (10μm or more in diameter) in the gas because its size affects the strength or erosion of the turbine blade. The aim of the present study is to observe the combustion phenomena relevant to a mixture of waste liquid and waste oil. Emphasis is placed on the ash size which is produced from the combustion chamber developed here. It is found that the ash size obtained at the exit of the combustor is less than 10 μm.

Numerical Study of Heat Transfer in Novel Wavy Trailing Edge Design for Gas Turbine Airfoils

2019 ◽  
Author(s):  
Sarwesh Parbat ◽  
Li Yang ◽  
Minking Chyu ◽  
Sin Chien Siw ◽  
Ching-Pang Lee
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Gas Turbine ◽  
Numerical Study ◽  
Turbine Blades ◽  
Suction Side ◽  
Inlet Temperature ◽  
Protective Film ◽  
Pressure Side ◽  
Trailing Edge

Abstract The strive to achieve increasingly higher efficiencies in gas turbine power generation has led to a continued rise in the turbine inlet temperature. As a result, novel cooling approaches for gas turbine blades are necessary to maintain them within the material’s thermal mechanical performance envelope. Various internal and external cooling technologies are used in different parts of the blade airfoil to provide the desired levels of cooling. Among the different regions of the blade profile, the trailing edge (TE) presents additional cooling challenges due to the thin cross section and high thermal loads. In this study, a new wavy geometry for the TE has been proposed and analyzed using steady state numerical simulations. The wavy TE structure resembled a sinusoidal wave running along the span of the blade. The troughs on both pressure side and suction side contained the coolant exit slots. As a result, consecutive coolant exit slots provided an alternating discharge between the suction side and the pressure side of the blade. Steady state conjugate heat transfer simulations were carried out using CFX solver for four coolant to mainstream mass flow ratios of 0.45%, 1%, 1.5% and 3%. The temperature distribution and film cooling effectiveness in the TE region were compared to two conventional geometries, pressure side cutback and centerline ejection which are widely used in vanes and blades for both land-based and aviation gas turbine engines. Unstructured mesh was generated for both fluid and solid domains and interfaces were defined between the two domains. For turbulence closer, SST-kω model was used. The wall y+ was maintained < 1 by using inflation layers at all the solid fluid interfaces. The numerical results depicted that the alternating discharge from the wavy TE was able to form protective film coverage on both the pressure and suction side of the blade. As a result, significant reduction in the TE metal was observed which was up to 14% lower in volume averaged temperature in the TE region when compared to the two baseline conventional configurations.

scholarly journals Gas turbine power calculation method of turboshaft based on simulation and performance model

2018 ◽  
Vol 189 ◽  
pp. 02003 ◽  
Author(s):  
Heng Wu ◽  
Shufan Zhao ◽  
Jijun Zhang ◽  
Bo Sun ◽  
Hanqiang Song
Keyword(s):  
Steady State ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Calculation Method ◽  
Performance Model ◽  
Power Calculation ◽  
Outlet Temperature ◽  
Acceptance Test ◽  
Test Drive ◽  
Turboshaft Engine

Gas turbine power of turboshaft engine cannot be measured, a total of five typical steady state point test data from the ground slow state to the maximum state were selected according to the factory acceptance test drive of a certain type of carrier-based helicopter turboshaft engine. Combustion chamber three-dimensional simulation model was established to carry on simulation analysis of different typical steady state combustion process. The simulated combustion chamber exit section parameters are input into the established gas turbine isentropic adiabatic aerodynamic calculation model to obtain the gas turbine power and outlet temperature. Select five typical steady state points of five sets of turboshaft engines on the same type to repeat the above calculation process, and compare the calculated value of gas turbine outlet temperature with the acceptance test values, it is found that the error values are all within 5%, and the effectiveness and accuracy of the gas turbine power calculation method are verified.

OH* Chemiluminescence and OH-PLIF Measurements in a Micro Gas Turbine Combustor

2010 ◽  
Author(s):  
Martina Hohloch ◽  
Rajesh Sadanandan ◽  
Axel Widenhorn ◽  
Wolfgang Meier ◽  
Manfred Aigner
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Thermal Power ◽  
Gas Turbine Combustor ◽  
Maximum Heat ◽  
Micro Gas Turbine ◽  
Power Load ◽  
Reaction Zones ◽  
Maximum Heat Release

In this work the combustion behavior of the Turbec T100 natural gas/air combustor was analyzed experimentally. For the visualization of the flame structures at various stationary load points OH* chemiluminescence and OH-PLIF measurements were performed in a micro gas turbine test rig equipped with an optically accessible combustion chamber. The OH* chemiluminescence measurements are used to get an impression of the shape and the location of the heat release zones. In addition the OH-PLIF measurements enabled spatially and temporarily resolved information of the reaction zones. Depending on the load point the shape of the flame was seen to vary from cylindrical to conical. With increasing thermal power load the maximum heat release zones shift to a lifted flame. Moreover, the effect of the optically accessible combustion chamber on the performance of the micro gas turbine is evaluated.

scholarly journals A swirler stabilized combustion chamber for a micro-gas turbine fuelled with natural gas

2012 ◽  
Vol 34 (4) ◽  
pp. 441-449 ◽  
Author(s):  
Guenther C. Krieger ◽  
André P. V. de Campos ◽  
Fernando L. Sacomano Filho ◽  
Rafael C. de Souza
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Micro Gas Turbine

scholarly journals An Infrared Pyrometry System for Monitoring Gas Turbine Blades: Development of a Computer Model and Experimental Results

1992 ◽  
Author(s):  
Maurizio De Lucia ◽  
Carlo Lanfranchi
Keyword(s):  
Steady State ◽  
Computer Modeling ◽  
Gas Turbine ◽  
Computer Model ◽  
Experimental Testing ◽  
Turbine Blades ◽  
Heat Fluxes ◽  
Radiation Heat ◽  
Gas Turbine Blades ◽  
Temperature Furnace

This work describes the development of a computer modeling system for infrared pyrometry measurement of gas turbine blade temperature. The model accurately evaluates apparent target emissivity and temperature on the basis of the radiation heat fluxes exchanged at steady-state conditions. Experimental testing conducted on gas turbine models in a controlled-temperature furnace has shown that the reliability of the target emissivity prediction effectively reduces one of the major causes of error in infrared pyrometry.

Sign in / Sign up

Export Citation Format

Share Document