Application of a Phenomenological Model for the Engine-Out Emissions of Unburned Hydrocarbons in Driving Cycles

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Manuel Dorsch ◽  
Jens Neumann ◽  
Christian Hasse
Keyword(s):  
Phenomenological Model ◽  
Combustion Engine ◽  
Combustion Process ◽  
Formation Mechanisms ◽  
Emission Model ◽  
Engine Operation ◽  
Driving Cycles ◽  
Hc Emissions ◽  
Piston Crevice ◽  
Engine Map

In this work, the application of a phenomenological model to determine engine-out hydrocarbon (HC) emissions in driving cycles is presented. The calculation is coupled to a physical-based simulation environment consisting of interacting submodels of engine, vehicle, and engine control. As a novelty, this virtual calibration methodology can be applied to optimize the energy conversion inside a spark-ignited (SI) internal combustion engine at transient operation. Using detailed information about the combustion process, the main origins and formation mechanisms of unburned HCs like piston crevice, oil layer, and wall quenching are considered in the prediction, as well as the in-cylinder postoxidation. Several parameterization approaches, especially, of the oil layer mechanism are discussed. After calibrating the emission model to a steady-state engine map, the transient results are validated successfully against measurements of various driving cycles based on different calibration strategies of engine operation.

scholarly journals Analytical Approach to the Exergy Destruction and the Simple Expansion Work Potential in the Constant Internal Energy and Volume Combustion Process

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 395
Author(s):  
Jeongwoo Song ◽  
Han Ho Song
Keyword(s):  
Internal Combustion Engine ◽  
Analytical Approach ◽  
Combustion Engine ◽  
Combustion Process ◽  
Internal Combustion ◽  
Thermodynamic System ◽  
Exergy Destruction ◽  
Engine Operation ◽  
System Temperature ◽  
Simple Expansion

The exergy destruction due to the irreversibility of the combustion process has been regarded as one of the key losses of an internal combustion engine. However, there has been little discussion on the direct relationship between the exergy destruction and the work output potential of an engine. In this study, an analytical approach is applied to discuss the relationship between the exergy destruction and efficiency by assuming a simple thermodynamic system simulating an internal combustion engine operation. In this simplified configuration, the exergy destruction during the combustion process is mainly affected by the temperature, which supports well-known facts in the literature. However, regardless of this exergy destruction, the work potential in this simple engine architecture is mainly affected by the pressure during the combustion process. In other words, if these pressure conditions are the same, increasing the system temperature to reduce the exergy destruction does not lead to an increase in the expansion work; rather, it only results in an increase in the remaining exergy after expansion. In a typical internal combustion engine, temperatures before combustion timing must be increased to reduce the exergy destruction, but increasing pressure before combustion timing is a key strategy to increase efficiency.

Fuel Consumption and Emissions in Transient Operation During Ship Maneuvering

2018 ◽  
Author(s):  
Felix Dahms ◽  
Michael Reska ◽  
Marko Püschel ◽  
Jürgen Nocke ◽  
Egon Hassel
Keyword(s):  
Simulation Model ◽  
Fuel Consumption ◽  
Combustion Engine ◽  
Operation Mode ◽  
Combustion Process ◽  
Transient Operation ◽  
Test Bed ◽  
Ship Maneuvering ◽  
Engine Operation ◽  
Chemical Reaction Kinetics

The following article details a method for the optimization and improved use of the internal combustion engine as main propulsion. The focus here is not on new propulsion systems or combustion processes, but on the characterization of the typical usage of existing systems in order to enable better utilization. As one major potential for improvement, the transient machinery operation is examined and discussed in this article. Higher fuel consumption and higher emissions occur compared with stationary engine operation in that operation mode. Experimental data from test bed (“Caterpillar MaK 6M20”) measurements are presented which explain the consequences of transient operation. Furthermore, appropriate analyzing methods to evaluate this operation mode are shown. Finally, a modelling approach is presented using the data for calibration and validation of an engine simulation model. The most significant part to predict real transient efficiency and emissions is the in-cylinder process and especially its combustion process. Therefore, the simulation model does not use engine maps but a mostly physically based engine model by using thermodynamic approaches and chemical reaction kinetics. The specific application of that simulation model for four-stroke medium-speed engines covers the behavior of transient operation during ship maneuverings since it is developed for integration into a ship engine simulator.

scholarly journals The influence of internal catalyst on exhaust emission in dynamic conditions

2018 ◽  
Vol 44 ◽  
pp. 00141 ◽  
Author(s):  
Jacek Pielecha ◽  
Monika Andrych-Zalewska
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Exhaust Emission ◽  
Technical Solution ◽  
Engine Operation ◽  
Static Tests ◽  
Negative Environmental Impact

The article discusses the use of an internal catalyst, which allows to reduce the emission of harmful compounds during internal combustion engine operation. This is a type of exhaust aftertreatment system; however, its placement inside the combustion chamber, and thus closest to the combustion process, allows reducing the pollution at the source (the catalyst was sprayed on the glow plugs). This is necessary because vehicle pollution reduction is a key aspect of reducing the negative environmental impact of transport. The presented research results are a part of a wider research scheme, on the evaluation of the internal catalyst impact in various engine operating conditions – starting from static tests (on an engine dynamometer), through dynamic dynamometer tests, and ending with vehicle road tests in real driving conditions. The use of an internal catalyst during dynamic tests results in a few percent reduction in the mass of carbon monoxide, hydrocarbons, carbon dioxide and the number of particulates in the considered measurement test. It is technically possible to introduce this kind of a technical solution in most vehicles with Diesel engines, thus resulting in improved ecological properties of internal combustion engines.

scholarly journals Analysis of the efficiency of the in-cylinder catalyst to reduce exhaust emissions during the cold start combustion engine

2019 ◽  
Vol 178 (3) ◽  
pp. 38-45
Author(s):  
Jerzy MERKISZ ◽  
Monika ANDRYCH-ZALEWSKA ◽  
Jacek PIELECHA
Keyword(s):  
Diesel Engine ◽  
Emission Reduction ◽  
Active Component ◽  
Negative Impact ◽  
Combustion Engine ◽  
Combustion Process ◽  
Exhaust Emissions ◽  
Exhaust Emission ◽  
Additional Method ◽  
Engine Operation

The article concerns the use of an in-cylinder catalyst that allows reducing the exhaust emissions during diesel engine operation. This is an additional method of exhaust emission reduction – however, the active component is placed inside the combustion chamber – hence much closest to the combustion process. This allows reducing the emissions at the very source (catalyst applied on the glow plugs). Such solutions are necessary because the reduction of exhaust emissions from vehicles is a key aspect of reducing the negative impact of transport on the environment.

A Global-Local Emission-Model for NOx and Soot Emissions of Turbocharged CR-Diesel Engines

2010 ◽  
Author(s):  
Heiko Sequenz ◽  
Matthias Mrosek ◽  
Rolf Isermann
Keyword(s):  
Dynamic Models ◽  
Combustion Process ◽  
Batch Process ◽  
Emission Model ◽  
Model Quality ◽  
Engine Operation ◽  
Input And Output ◽  
Soot Emissions ◽  
Prediction And Simulation ◽  
Output Space

Stationary and dynamic models for the emissions of a CR-Diesel engine are developed using a global-local model approach. Results for the NOx and soot emissions are presented. All model inputs are measurable air path states and combustion parameters. They determine the emission formation before the combustion takes place. Therefore the model can be used for emission prediction and simulation. The combustion process is regarded as a batch process, such that the dynamics are introduced as external dynamics to the model via the inputs. Thus a stationary model structure can be applied. As the space of possible air path states varies widely for different engine operation points, several input and output transformations are given that linearize the input and output space. This improves the model quality and extends the operation range of the model. Modeling results are shown for stationary and dynamic data as well as for local and global model operation.

The Advanced Injection Low Pilot Ignited Natural Gas Engine: A Combustion Analysis

2004 ◽  
Vol 128 (1) ◽  
pp. 213-218 ◽  
Author(s):  
K. K. Srinivasan ◽  
S. R. Krishnan ◽  
S. Singh ◽  
K. C. Midkiff ◽  
S. R. Bell ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Engine Operation ◽  
Natural Gas Engines ◽  
Full Load Operation ◽  
Dual Fuel Engines ◽  
Engine Stability ◽  
Hc Emissions ◽  
The Stability ◽  
Conversion Efficiencies

The Advanced (injection) Low Pilot Ignited Natural Gas (ALPING) engine is proposed as an alternative to diesel and conventional dual fuel engines. Experimental results from full load operation at a constant speed of 1700rev∕min are presented in this paper. The potential of the ALPING engine is realized in reduced NOx emissions (to less than 0.2g∕kWh) accompanied by fuel conversion efficiencies comparable to straight diesel operation. Some problems at advanced injection timings are recognized in high unburned hydrocarbon (HC) emissions (25g∕kWh) and poor engine stability reflected by high COVIMEP (about 6%). This paper focuses on the combustion aspects of low pilot ignited natural gas engines with particular emphasis on advanced injection timings (45°–60° BTDC). Ignition phasing at advanced injection timings (∼60° BTDC), and combustion phasing at retarded injection timings (∼15° BTDC) are recognized as important combustion parameters that profoundly impact the combustion process, HC emissions, and the stability of engine operation.

scholarly journals Free Stream Behavior of Hydrogen Released from a Fluidic Oscillating Nozzle

Fluids ◽  
2021 ◽  
Vol 6 (7) ◽  
pp. 245
Author(s):  
Anja Fink ◽  
Oliver Nett ◽  
Simon Schmidt ◽  
Oliver Krüger ◽  
Thomas Ebert ◽  
...  
Keyword(s):  
Free Stream ◽  
Combustion Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Vertical Direction ◽  
Spray Angle ◽  
Transport Sector ◽  
Flow Measurements ◽  
Injection Process ◽  
Bottom Dead Center

The H2 internal combustion engine (ICE) is a key technology for complete decarbonization of the transport sector. To match or exceed the power density of conventional combustion engines, H2 direct injection (DI) is essential. Therefore, new injector concepts that meet the requirements of a H2 operation have to be developed. The macroscopic free stream behavior of H2 released from an innovative fluidic oscillating nozzle is investigated and compared with that of a conventional multi-hole nozzle. This work consists of H2 flow measurements and injection tests in a constant volume chamber using the Schlieren method and is accompanied by a LES simulation. The results show that an oscillating H2 free stream has a higher penetration velocity than the individual jets of a multi-hole nozzle. This behavior can be used to inject H2 far into the combustion chamber in the vertical direction while the piston is still near bottom dead center. As soon as the oscillation of the H2 free stream starts, the spray angle increases and therefore H2 is also distributed in the horizontal direction. In this phase of the injection process, spray angles comparable to those of a multi-hole nozzle are achieved. This behavior has a positive effect on H2 homogenization, which is desirable for the combustion process.

Effects of H2 Addition to CNG Blends on Cycle-to-Cycle and Cylinder-to-Cylinder Combustion Variation in an SI Engine

2012 ◽  
Author(s):  
Mirko Baratta ◽  
Stefano d’Ambrosio ◽  
Daniela Misul ◽  
Ezio Spessa
Keyword(s):  
Diagnostic Tool ◽  
Combustion Process ◽  
Experimental Tests ◽  
Test Point ◽  
Pollutant Emissions ◽  
Engine Operation ◽  
Pressure Transducers ◽  
Rate Analysis ◽  
Spark Plug ◽  
Wide Range

An experimental investigation and a burning-rate analysis have been performed on a production 1.4 liter CNG (compressed natural gas) engine fueled with methane-hydrogen blends. The engine features a pent-roof combustion chamber, four valves per cylinder and a centrally located spark plug. The experimental tests have been carried out in order to quantify the cycle-to-cycle and the cylinder-to-cylinder combustion variation. Therefore, the engine has been equipped with four dedicated piezoelectric pressure transducers placed on each cylinder and located by the spark plug. At each test point, in-cylinder pressure, fuel consumption, induced air mass flow rate, pressure and temperature at different locations on the engine intake and exhaust systems as well as ‘engine-out’ pollutant emissions have been measured. The signals correlated to the engine operation have been acquired by means of a National Instruments PXI-DAQ system and a home developed software. The acquired data have then been processed through a combustion diagnostic tool resulting from the integration of an original multizone thermodynamic model with a CAD procedure for the evaluation of the burned-gas front geometry. The diagnostic tool allows the burning velocities to be computed. The tests have been performed over a wide range of engine speeds, loads and relative air-fuel ratios (up to the lean operation). For stoichiometric operation, the addition of hydrogen to CNG has produced a bsfc reduction ranging between 2 to 7% and a bsTHC decrease up to the 40%. These benefits have appeared to be even higher for lean mixtures. Moreover, hydrogen has shown to significantly enhance the combustion process, thus leading to a sensibly lower cycle-to-cycle variability. As a matter of fact, hydrogen addition has generally resulted into extended operation up to RAFR = 1.8. Still, a discrepancy in the abovementioned conclusions was observed depending on the engine cylinder considered.

Analysis and Research of the Combustion Process of YN4100QB Diesel Engine

2013 ◽  
Vol 744 ◽  
pp. 35-39
Author(s):  
Lei Ming Shi ◽  
Guang Hui Jia ◽  
Zhi Fei Zhang ◽  
Zhong Ming Xu
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Optimization Design ◽  
Combustion Engine ◽  
Geometric Model ◽  
Combustion Process ◽  
Internal Combustion ◽  
Engine Combustion ◽  
Exhaust Noise

In order to obtain the foundation to the research on the Diesel Engine YN4100QB combustion process, exhaust, the optimal design of combustion chamber and the useful information for the design of exhaust muffler, the geometric model and mesh model of a type internal combustion engine are constructed by using FIRE software to analyze the working process of internal combustion engine. Exhaust noise is the main component of automobile noise in the study of controlling vehicle noise. It is primary to design a type of muffler which is good for agricultural automobile engine matching and noise reduction effect. The present car mufflers are all development means. So it is bound to cause the long cycle of product development and waste of resources. Even sometimes not only can it not reach the purpose of reducing the noise but also it leads to reduce the engine dynamic. The strength of the exhaust noise is closely related to engine combustion temperature and pressure. The calculation and initial parameters are applied to the software based on the combustion model and theory. According to the specific operation process of internal combustion engine. Five kinds of common operation condition was compiled. It is obtained for the detailed distribution parameters of combusted gas temperature pressure . It is also got for flow velocity of the fields in cylinder and given for the relation of the parameters and crankshaft angle for the further research. At the same time NOx emissions situation are got. The numerical results show that not only does it provide the 3D distribution data in different crank shaft angle inside the cylinder in the simulation of combustion process, but also it provides a basis for the engine combustion ,emission research, the optimization design of the combustion chamber and the useful information for the designs of muffler.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

Sign in / Sign up

Export Citation Format

Share Document