Porous Silicon Morphology: Photo-Electrochemically Etched by Different Laser Wavelengths

2015 ◽  
Vol 6 (1) ◽  
Author(s):  
Shereen M. Faraj ◽  
Shaimaa M. Abd Al-Baqi ◽  
Nasreen R. Jber ◽  
Johnny Fisher
Keyword(s):  
Porous Silicon ◽  
Electrochemical Etching ◽  
Diode Lasers ◽  
Focus Of Attention ◽  
Blue Laser ◽  
Uniform Structure ◽  
Porous Layers ◽  
Current Densities ◽  
P Type ◽  
532 Nm

Porous silicon (PS) has become the focus of attention in upgrading silicon for optoelectronics. In this work, various structures were produced depending on the formation parameters by photo-electrochemical etching (PECE) process of n- and p-type silicon wafer at different time durations (5–90 mins) and different current densities (5, 15, and 20 mA/cm2) for each set of time durations. Diode lasers of 405 nm, 473 nm, and 532 nm wavelengths, each 50 mW power, were used to illuminate the surface of the samples during the etching process. The results showed that controlled porous layers were achieved by using blue laser, giving uniform structure which can make it possible to dispense with expensive methods of patterning the silicon.

scholarly journals Photo and electroluminescence of porous silicon layers

BIBECHANA ◽  
2012 ◽  
Vol 8 ◽  
pp. 46-52
Author(s):  
E Haji-Ali
Keyword(s):  
Porous Silicon ◽  
Light Emission ◽  
Electrochemical Cell ◽  
Electrochemical Etching ◽  
Light Illumination ◽  
Porous Layers ◽  
Si Substrates ◽  
Orange Yellow ◽  
Intense Light ◽  
P Type

Porous silicon layers were prepared by both chemical and electrochemical methods on n- and ptype Si substrates. In the former technique, light emission was obtained from p-type and n-type samples. It was found that intense light illumination during the preparation process was essential for PSi formation on n-type substrates.An efficient electrochemical cell with some useful features was designed for electrochemical etching of silicon. Various preparation parameters were studied and photoluminescence emissions ranging from dark red to light blue were obtained from PSi samples prepared on p-type substrates. N-type samples produced emissions ranging from dark red to orange-yellow. Electroluminescence of porous silicon samples showed that the color of the emission was the same as the photoluminescence color of the sample, and its intensity and duration depended on the current density passed through the sample. The effects of exposure of samples to air, storage in vacuum, and heat-treatment in air on luminescence intensity of the samples and preparation of patterned porous layers were also studied.Keywords: Porous silicon layers; photoluminescence; electroluminescenceDOI: http://dx.doi.org/10.3126/bibechana.v8i0.4897  BIBECHANA 8 (2012) 46-52

scholarly journals Porous Silicon Biosensor for the Detection of Bacteria through Their Lysate

Biosensors ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 27
Author(s):  
Roselien Vercauteren ◽  
Audrey Leprince ◽  
Jacques Mahillon ◽  
Laurent A. Francis
Keyword(s):  
Porous Silicon ◽  
Electrochemical Etching ◽  
Bacterial Lysate ◽  
Fast Detection ◽  
Porous Layers ◽  
Deep Blue ◽  
Diffusion Limited ◽  
Colony Forming Units ◽  
Selective Lysis ◽  
Microfabrication Techniques

Porous silicon (PSi) has been widely used as a biosensor in recent years due to its large surface area and its optical properties. Most PSi biosensors consist in close-ended porous layers, and, because of the diffusion-limited infiltration of the analyte, they lack sensitivity and speed of response. In order to overcome these shortcomings, PSi membranes (PSiMs) have been fabricated using electrochemical etching and standard microfabrication techniques. In this work, PSiMs have been used for the optical detection of Bacillus cereus lysate. Before detection, the bacteria are selectively lysed by PlyB221, an endolysin encoded by the bacteriophage Deep-Blue targeting B. cereus. The detection relies on the infiltration of bacterial lysate inside the membrane, which induces a shift of the effective optical thickness. The biosensor was able to detect a B. cereus bacterial lysate, with an initial bacteria concentration of 105 colony forming units per mL (CFU/mL), in only 1 h. This proof-of-concept also illustrates the specificity of the lysis before detection. Not only does this detection platform enable the fast detection of bacteria, but the same technique can be extended to other bacteria using selective lysis, as demonstrated by the detection of Staphylococcus epidermidis, selectively lysed by lysostaphin.

Structural, Surface Morphological and Photoluminescence Properties of Nanostructured Porous Silicon Material for Optoelectronics Application

2012 ◽  
Vol 584 ◽  
pp. 290-294 ◽  
Author(s):  
Jeyaprakash Pandiarajan ◽  
Natarajan Jeyakumaran ◽  
Natarajan Prithivikumaran
Keyword(s):  
Porous Silicon ◽  
Current Density ◽  
Light Emission ◽  
Electrochemical Etching ◽  
Light Emitting Diode ◽  
Radiative Transition ◽  
Sem Images ◽  
Optoelectronic Application ◽  
Gap Opening ◽  
P Type

The promotion of silicon (Si) from being the key material for microelectronics to an interesting material for optoelectronic application is a consequence of the possibility to reduce its device dimensionally by a cheap and easy technique. In fact, electrochemical etching of Si under controlled conditions leads to the formation of nanocrystalline porous silicon (PS) where quantum confinement of photo excited carriers and surface species yield to a band gap opening and an increased radiative transition rate resulting in efficient light emission. In the present study, the nanostructured PS samples were prepared using anodic etching of p-type silicon. The effect of current density on structural and optical properties of PS, has been investigated. XRD studies confirm the presence of silicon nanocrystallites in the PS structure. By increasing the current density, the average estimated values of grain size are found to be decreased. SEM images indicate that the pores are surrounded by a thick columnar network of silicon walls. The observed PL spectra at room temperature for all the current densities confirm the formation of PS structures with nanocrystalline features. PL studies reveal that there is a prominent visible emission peak at 606 nm. The obtained variation of intensity in PL emission may be used for intensity varied light emitting diode applications. These studies confirm that the PS is a versatile material with potential for optoelectronics application.

Electroluminescence and Photoluminescence Properties of Porous Silicon Nanostructures with Optimum Current Density of Photo-Electrochemical Anodisation

2013 ◽  
Vol 667 ◽  
pp. 180-185
Author(s):  
M. Ain Zubaidah ◽  
F.S. Husairi ◽  
S.F.M. Yusop ◽  
Noor Asli Asnida ◽  
Mohamad Rusop ◽  
...  
Keyword(s):  
Porous Silicon ◽  
Volume Ratio ◽  
Boron Doping ◽  
Peak Position ◽  
Silicon Nanostructures ◽  
Etching Time ◽  
Photoluminescence Properties ◽  
Current Densities ◽  
Pl Spectrum ◽  
P Type

P-type silicon wafer ( orientation; boron doping; 0.75 ~ 10 Ω cm-1) was used to prepare samples of porous silicon nanostructures (PSiNs). All samples have been prepared by using photo-electrochemical anodisation. A fixed etching time of 30 minutes and volume ratio of electrolyte, hydrofluoric acid 48% (HF48%) and absolute ethanol (C2H5OH), 1:1 were used for various current densities, J. There were sample A (J=10 mA/cm2), sample B (J=20 mA/cm2), sample C (J=30 mA/cm2), sample D (J=40 mA/cm2) and sample E (J=50 mA/cm2). Photoluminescence (PL) and electroluminescence (EL) spectra were investigated. Maximum peak position of PL spectrum at about ~675 nm, while the maximum EL spectrum at about ~650 nm (which is similar to the PL spectrum).

Optical Properties of Free-Standing Ultrahigh Porosity Silicon Films Prepared by Supercritical Drying

1996 ◽  
Vol 452 ◽  
Author(s):  
J. Von Behren ◽  
P. M. Fauchet ◽  
E. H. Chimowitz ◽  
C. T. Lira
Keyword(s):  
Porous Silicon ◽  
Electrochemical Etching ◽  
Supercritical Drying ◽  
Silicon Films ◽  
Index Of Refraction ◽  
Free Standing ◽  
Crystal Silicon ◽  
Si Substrates ◽  
Type C ◽  
P Type

AbstractHighly luminescent free-standing porous silicon thin films of excellent optical quality have been manufactured by using electrochemical etching and lift-off steps combined with supercritical drying. One to 50 μm thick free-standing layers made from highly (p+) and moderately (p) Boron doped single crystal silicon (c-Si) substrates have been produced with porosities (P) up to 95 %. The Fabry-Pérot fringes observed in the transmission and photoluminescence (PL) spectra are used to determine the refractive index. At the highest P the index of refraction is below 1.2 from the IR to 2 eV. The absorption coefficients follow a nearly exponential behavior in the energy range from 1.2 eV and 4 eV. The porosity corrected absorption spectra of free-standing films made from p type c-Si substrates are blue shifted with respect to those prepared from p+ substrates. For P > 70 % a blue shift is also observed in PL. At equal porosities the luminescence intensities of porous silicon films made from p+ and p type c-Si are different by one order of magnitude.

I-V and Surface Topography Study of Nanostructure Porous Silicon Layer Prepared by Electrochemical Etching

2012 ◽  
Vol 576 ◽  
pp. 519-522 ◽  
Author(s):  
Fadzilah Suhaimi Husairi ◽  
Maslihan Ain Zubaidah ◽  
Shamsul Faez M. Yusop ◽  
Rusop Mahmood Mohamad ◽  
Saifolah Abdullah
Keyword(s):  
Electrical Properties ◽  
Porous Silicon ◽  
Surface Topography ◽  
Electrochemical Etching ◽  
Silicon Layer ◽  
Porous Silicon Layer ◽  
Force Microscopy ◽  
Atomic Force ◽  
Current Voltage ◽  
P Type

This article reports on the electrical properties of porous silicon nanostructures (PSiNs) in term of its surface topography. In this study, the PsiNs samples were prepared by using different current density during the electrochemical etching of p-type silicon wafer. PSiNs has been investigated its electrical properties and resistances for different surface topography of PSiNs via current-voltage (I-V) measurement system (Keithley 2400) while its physical structural properties was investigated by using atomic force microscopy (AFM-XE100).

scholarly journals Peculiarities of Photoluminescence in Porous Silicon Prepared by Metal-Assisted Chemical Etching

ISRN Optics ◽  
2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Igor Iatsunskyi ◽  
Valentin Smyntyna ◽  
Nykolai Pavlenko ◽  
Olga Sviridova
Keyword(s):  
Porous Silicon ◽  
Chemical Etching ◽  
Etching Time ◽  
Force Microscopy ◽  
Porous Layers ◽  
Atomic Force ◽  
Silicon Nanostructure ◽  
Metal Assisted Chemical Etching ◽  
Concentrated Solution ◽  
P Type

Photoluminescent (PL) porous layers were formed on p-type silicon by a metal-assisted chemical etching method using H2O2 as an oxidizing agent. Silver particles were deposited on the (100) Si surface prior to immersion in a solution of HF and H2O2. The morphology of the porous silicon (PS) layer formed by this method was investigated by atomic force microscopy (AFM). Depending on the metal-assisted chemical etching conditions, the macro- or microporous structures could be formed. Luminescence from metal-assisted chemically etched layers was measured. It was found that the PL intensity increases with increasing etching time. This behaviour is attributed to increase of the density of the silicon nanostructure. It was found the shift of PL peak to a green region with increasing of deposition time can be attributed to the change in porous morphology. Finally, the PL spectra of samples formed by high concentrated solution of AgNO3 showed two narrow peaks of emission at 520 and 550 nm. These peaks can be attributed to formation of AgF and AgF2 on a silicon surface.

scholarly journals Porous Silicon Biosensor for the Detection of Bacteria through Their Lysate

Proceedings ◽  
2020 ◽  
Vol 60 (1) ◽  
pp. 36
Author(s):  
Roselien Vercauteren ◽  
Audrey Leprince ◽  
Jacques Mahillon ◽  
Laurent A. Francis
Keyword(s):  
Porous Silicon ◽  
Electrochemical Etching ◽  
Bacterial Lysate ◽  
Fast Detection ◽  
Porous Layers ◽  
Deep Blue ◽  
Diffusion Limited ◽  
Colony Forming Units ◽  
Selective Lysis ◽  
Microfabrication Techniques

Porous silicon (PSi) has been widely used as a biosensor over the last years due to its large surface area and its optical properties. Most PSi biosensors consist in close-ended porous layers, and, because of the diffusion-limited infiltration of the analyte, they lack sensitivity and speed of response. In order to overcome these shortcomings, PSi membranes (PSiMs) have been fabricated using electrochemical etching and standard microfabrication techniques. In this work, PSiMs have been used for the optical detection of Bacillus cereus lysate. Before detection, the bacteria are selectively lysed by PlyB221, an endolysin encoded by the bacteriophage Deep-Blue targeting B. cereus. The detection relies on the infiltration of bacterial lysate inside the membrane, which induces a shift of the effective optical thickness. The biosensor was able to detect a B. cereus bacterial lysate, with an initial bacteria concentration of 106 colony forming units per mL (CFU/mL), in less than 10 min. This work also demonstrates the selectivity of the lysis before detection. Not only does this detection platform enable the fast detection of bacteria, but the same technique can be extended to other bacteria using selective lysis.

Elaboration and Light Emission Properties of Low Doped p-Type Porous Silicon Microcavities

1996 ◽  
Vol 452 ◽  
Author(s):  
G. Lérondel ◽  
P. Ferrand ◽  
R. Romestain
Keyword(s):  
Porous Silicon ◽  
Near Infrared ◽  
Light Emission ◽  
Narrow Band ◽  
Bragg Reflectors ◽  
Strong Emission ◽  
Luminescence Efficiency ◽  
Fabry Perot ◽  
Current Densities ◽  
P Type

AbstractWe account for the elaboration of Bragg reflectors and microcavities based on efficiently luminescent porous silicon. A characterisation of very thin porous silicon layers obtained with current densities of formation varying from 1.5 mA to 300 mA is presented. The resulting refractive index variation (typically from 1.37 to 1.86 at 700 nm) enables the elaboration of high quality Bragg reflectors and Fabry-Perot filters from the yellow to the near infrared. Although low doped p-type porous silicon develops rougher interfaces than highly doped p-type porous silicon, its better luminescence efficiency has enabled us to elaborate microcavities with a strong emission in a narrow band.

Sign in / Sign up

Export Citation Format

Share Document