The Effect of an Eroded Leading Edge on the Aerodynamic Performance of a Transonic Fan Blade Cascade

2014 ◽  
Vol 137 (2) ◽  
Author(s):  
Alexander Hergt ◽  
J. Klinner ◽  
W. Steinert ◽  
S. Grund ◽  
M. Beversdorff ◽  
...  
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Separation Bubble ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Performance ◽  
Chord Length ◽  
Blade Cascade ◽  
Shock Position ◽  
Fan Blade

Especially at transonic flow conditions the leading edge shape influences the performance of a fan profile. At the same time the leading edge of a fan profile is highly affected by erosion during operation. This erosion leads to a deformation of the leading edge shape and a reduction of the chord length. In the present experimental and numerical study, the aerodynamic performance of an original fan profile geometry is compared to an eroded fan profile with a blunt leading edge (BLE) and a chord length reduced by about 1%. The experiments are performed at a linear fan blade cascade in the Transonic Cascade Wind Tunnel of DLR in Cologne. The inflow Mach number during the tests is 1.25 and the Reynolds number 1.5 × 106. All tests are carried out at a low inflow turbulence level of 0.8%. The results of the investigation show that losses are increased over the whole operating range of the cascade. At the aerodynamic design point (ADP) the losses raise by 25%. This significant loss increase can be traced back to the increase of the shock losses at the leading edge. The change in shock structure is investigated and described in detail by means of particle image velocimetry (PIV) measurements and Schlieren imaging. Additionally, the unsteady fluctuation of the shock position is measured by a high-speed shadowgraphy. Then the frequency range of the fluctuation is obtained by a Fourier analysis of the time resolved shock position. Furthermore, liquid crystal measurements are performed in order to analyze the influence of the leading edge shape on the development of the suction side boundary layer. The results show that for the original fan blade the transition occurs at the shock position on the blade suction side by a separation bubble whereas the transition onset is shifted upstream for the fan blade with the BLE.

The Effect of an Eroded Leading Edge on the Aerodynamic Performance of a Transonic Fan Blade Cascade

2014 ◽  
Author(s):  
A. Hergt ◽  
J. Klinner ◽  
W. Steinert ◽  
S. Grund ◽  
M. Beversdorff ◽  
...  
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Separation Bubble ◽  
Leading Edge ◽  
Suction Side ◽  
Chord Length ◽  
Blade Cascade ◽  
Shock Position ◽  
Fan Blade ◽  
Blunt Leading Edge

Especially at transonic flow conditions the leading edge shape influences the performance of a fan profile. At the same time the leading edge of a fan profile is highly affected by erosion during operation. This erosion leads to a deformation of the leading edge shape and a reduction of the chord length. In the present experimental and numerical study, the aerodynamic perfomance of an original fan profile geometry is compared to an eroded fan profile with a blunt leading edge and a chord length reduced by about 1 percent. The experiments are performed at a linear fan blade cascade in the Transonic Cascade Wind Tunnel of DLR in Cologne. The inflow Mach number during the tests is 1.25 and the Reynolds number 1.5 × 106. All tests are carried out at a low inflow turbulence level of 0.8 percent. The results of the investigation show that losses are increased over the whole operating range of the cascade. At the aerodynamic design point the losses raise by 25 percent. This significant loss increase can be traced back to the increase of the shock losses at the leading edge. The change in shock structure is investigated and described in detail by means of PIV measurements and Schlieren imaging. Additionally, the unsteady fluctuation of the shock position is measured by a high speed shadowgraphy. Then the frequency range of the fluctuation is obtained by a Fourier analysis of the time resolved shock position. Furthermore, liquid crystal measurements are performed in order to analyze the influence of the leading edge shape on the development of the suction side boundary layer. The results show that for the original fan blade the transition occurs at the shock position on the blade suction side by a separation bubble whereas the transition onset is shifted upstream for the fan blade with the blunt leading edge.

scholarly journals Flow control in linear compressor cascades by inclusion of suction side dimples at varying locations

2018 ◽  
Vol 232 (6) ◽  
pp. 706-721 ◽  
Author(s):  
Hua-wei Lu ◽  
Yi Yang ◽  
Shang Guo ◽  
Yu-xuan Huang ◽  
Hong Wang ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Pressure Rise ◽  
Suction Side ◽  
Aerodynamic Performance ◽  
Chord Length ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Linear Compressor ◽  
Comparison Results

The flow characteristics and loss behavior over an array of parallel recessed dimples on a high turning linear compressor cascade have been investigated using the Reynolds-averaged Navier–Stokes approach. Steady simulations have been carried out at three dimple locations of 10–32%, 38–60%, 60–82% chord length of suction surface with the inlet Mach number of 0.7. Flow conditions were compared in exit loss coefficient, static pressure rise, streamline patterns, vortex structures, boundary layer parameters, and blade surface pressure between the smooth and the modified cascades. The results indicate that the dimples prior to the separation line report an overall enhancement in the aerodynamic performance in comparison to that of a smooth blade. Symmetric spanwise vortex, which energizes the boundary layer, can roll up inside the dimples. Therefore, the boundary layer with the higher momentum can bear the adverse pressure gradient, which will suppress the flow separation and associated losses. Three dimpled configurations can all eliminate the separation bubble on the suction side, but the dimples located at 60–82% chord length take the negative effect on the aerodynamic performance due to the more chaos condition in the corner separation region. The comparison results also indicate that the optimum location of dimples may exist in front of the separation bubble. Loss reduction of 18.8% and 10.8% can be achieved under the 10–32% c and 38–60% c dimple configurations, respectively.

Experimental and Numerical Study on Flapping Wing Kinematics and Aerodynamics of Coleoptera

2006 ◽  
Vol 326-328 ◽  
pp. 175-178 ◽  
Author(s):  
Saputra ◽  
Do Young Byun ◽  
Yung Hwan Byun ◽  
Hoon Cheol Park
Keyword(s):  
Cross Section ◽  
High Speed ◽  
Numerical Study ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Wing Kinematics ◽  
Wing Motion ◽  
Edge Vortex ◽  
Flapping Mechanism ◽  
Aerodynamic Simulation

In this study we have experimentally and numerically analyzed the flapping mechanism and wing kinematics of coleoptera (Propylea japonica Thunberg). Using digital high speed camera, we captured the continuous wing kinematics and visualized the flight motion of the free-flying coleoptera. The experimental visualization shows that the elytra flapped concurrently with the main wing both in the downstroke and upstroke motions. In order to define the wing kinematics of coleoptera, the displacement of a wing cross section (50% span-wise) was measured for each sequence of the wing motion. Using these data, the flight motion of coleoptera was numerically simulated to investigate the aerodynamic performance. The computational aerodynamic simulation shows that leading edge vortex shedding plays a key role in generating lift to keep the insect aloft.

scholarly journals Effect of Chordwise Struts and Misaligned Flow on the Aerodynamic Performance of a Leading-Edge Inflatable Wing

2021 ◽  
Author(s):  
Axelle Viré ◽  
Geert Lebesque ◽  
Mikko Folkersma ◽  
Roland Schmehl
Keyword(s):  
Separation Bubble ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Local Flow ◽  
Energy Applications ◽  
Flow Configurations ◽  
Lift And Drag

Steady-state Reynolds-Averaged Navier-Stokes (RANS) simulations are performed for a leading-edge inflatable wing for airborne wind energy applications. Expanding on previous work where only the inflatable leading edge tube was considered, eight additional inflatable strut tubes that support the wing canopy are now included. The shape of the wing is considered to be constant. The influence of the strut tubes on the aerodynamic performance of the wing and the local flow field is assessed, considering flow configurations with and without side-slip. The simulations show that the aerodynamic performance of the wing decreases with increasing side-slip component of the inflow. On the other hand, the chordwise struts have little influence on the integral lift and drag of the wing, irrespective of the side-slip component. The overall flow characteristics are in good agreement with previous studies. In particular, it is confirmed that at a low Reynolds number of Re=10^5, a laminar separation bubble exists on the suction side of this hypothetical rigid wing shape with perfectly smooth surface. The destruction of this bubble at low angles of attack impacts negatively on the aerodynamic performance.

scholarly journals Numerical Analysis of Effect of Leading-Edge Rotating Cylinder on NACA0021 Symmetric Airfoil

2019 ◽  
Vol 4 (7) ◽  
pp. 11-17
Author(s):  
Md. Abdus Salam ◽  
Vikram Deshpande ◽  
Nafiz Ahmed Khan ◽  
M. A. Taher Ali
Keyword(s):  
Free Stream ◽  
Numerical Study ◽  
Tangential Velocity ◽  
Leading Edge ◽  
Rotating Cylinder ◽  
Aerodynamic Performance ◽  
Stream Velocity ◽  
Surface Boundary ◽  
Lower Velocity ◽  
Numerical Studies

The moving surface boundary control (MSBC) has been a Centre stage study for last 2-3 decades. The preliminary aim of the study was to ascertain whether the concept can improve the airfoil characteristics. Number of experimental and numerical studies pointed out that the MSBC can superiorly enhance the airfoil performance albeit for higher velocity ratios (i.e. cylinder tangential velocity to free stream velocity). Although abundant research has been undertaken in this area on different airfoil performances but no attempt was seen to study effect of MSBC on NACA0021 airfoil for and also effects of lower velocity ratios. Thus, present paper focusses on numerical study of modified NACA 0021 airfoil with leading edge rotating cylinder for velocity ratios (i.e.) between 1 to 1.78 at different angles of attack. The numerical study indicates that the modified airfoil possess better aerodynamic performance than the base airfoil even at lower velocity ratios (i.e. for velocity ratios 0.356 and beyond). The study also focusses on reason for improvement in aerodynamic performance by close look at various parameters.

A Numerical Study Into the Influence of Leading Edge Tubercles on the Aerodynamic Performance of a Highly Cambered High Lift Airfoil Wing at Different Reynolds Numbers

2020 ◽  
Author(s):  
Amr Abdelrahman ◽  
Amr Emam ◽  
Ihab Adam ◽  
Hamdy Hassan ◽  
Shinichi Ookawara ◽  
...  
Keyword(s):  
Control Method ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Stall Angle ◽  
Lifting Surfaces ◽  
Lift And Drag

Abstract Through the last two decades, many studies have demonstrated the ability of leading-edge protrusions (tubercles), inspired from the pectoral flippers of the humpback whale, to be an effective passive flow control method for the stall phase of an airfoil in some cases depending on the geometrical features and the flow regime. Nevertheless, there is a little work associated with revealing tubercles performance for the lifting surfaces with a highly cambered cross-section, used in numerous applications. The present work aims to investigate the effect of implementing leading edge tubercles on the performance of an infinite span rectangular wing with the highly cambered S1223 foil at different flow regimes. Two sets; baseline one and a modified with tubercles have been studied at Re = 0.1 × 106, 0.3 × 106 and 1.5 × 106 using computational fluid dynamics with a validated model. The numerical results demonstrated that Tubercles have the ability to entirely alter the flow structure over the airfoil, confining the separation to troughs, hence, softening the stall characteristics. However, the tubercle modification expedites the presence of the stalled flow over the suction side, lowering the stall angle for the three mentioned Reynolds numbers. While, no considerable difference occurs in lift and drag before the stall.

Acoustic and phase portrait analysis of leading-edge roughness element on laminar separation bubbles at low Reynolds number flow

2021 ◽  
pp. 095441002110443
Author(s):  
Hossein Jabbari ◽  
Esmaeili Ali ◽  
Mohammad Hasan Djavareshkian
Keyword(s):  
Reynolds Number ◽  
Phase Portrait ◽  
Separation Bubble ◽  
Roughness Element ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Suction Side ◽  
Laminar Separation ◽  
Roughness Elements ◽  
Edge Roughness

Since laminar separation bubbles are neutrally shaped on the suction side of full-span wings in low Reynolds number flows, a roughness element can be used to improve the performance of micro aerial vehicles. The purpose of this article was to investigate the leading-edge roughness element’s effect and its location on upstream of the laminar separation bubble from phase portrait point of view. Therefore, passive control might have an acoustic side effect, especially when the bubble might burst and increase noise. Consequently, the effect of the leading-edge roughness element features on the bubble’s behavior is considered on the acoustic pressure field and the vortices behind the NASA-LS0417 cross-section. The consequences express that the distribution of roughness in the appropriate dimensions and location could contribute to increasing the performance of the airfoil and the interaction of vortices produced by roughness elements with shear layers on the suction side has increased the sound frequency in the relevant sound pressure level (SPL). The results have demonstrated that vortex shedding frequency was increased in the presence of roughness compared to the smooth airfoil. Also, more complexity of the phase portrait circuits was found, retrieved from velocity gradient limitation. Likewise, the highest SPL is related to the state where the separation bubble phenomenon is on the surface versus placing roughness elements on the leading edge leads to a negative amount of SPL.

scholarly journals Numerical Study of Sediment Erosion Analysis in Francis Turbine

2019 ◽  
Vol 11 (5) ◽  
pp. 1423 ◽  
Author(s):  
Md Rakibuzzaman ◽  
Hyoung-Ho Kim ◽  
Kyungwuk Kim ◽  
Sang-Ho Suh ◽  
Kyung Kim
Keyword(s):  
Erosion Rate ◽  
Cavitation Erosion ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Hydraulic Turbine ◽  
Francis Turbine ◽  
Trailing Edge ◽  
Sand Erosion ◽  
Turbine Design

Effective hydraulic turbine design prevents sediment and cavitation erosion from impacting the performance and reliability of the machine. Using computational fluid dynamics (CFD) techniques, this study investigated the performance characteristics of sediment and cavitation erosion on a hydraulic Francis turbine by ANSYS-CFX software. For the erosion rate calculation, the particle trajectory Tabakoff–Grant erosion model was used. To predict the cavitation characteristics, the study’s source term for interphase mass transfer was the Rayleigh–Plesset cavitation model. The experimental data acquired by this study were used to validate the existing evaluations of the Francis turbine. Hydraulic results revealed that the maximum difference was only 0.958% compared with the CFD data, and 0.547% compared with the experiment (Korea Institute of Machinery and Materials (KIMM)). The turbine blade region was affected by the erosion rate at the trailing edge because of their high velocity. Furthermore, in the cavitation–erosion simulation, it was observed that abrasion propagation began from the pressure side of the leading edge and continued along to the trailing edge of the runner. Additionally, as sediment flow rates grew within the area of the attached cavitation, they increased from the trailing edge at the suction side, and efficiency was reduced. Cavitation–sand erosion results then revealed a higher erosion rate than of those of the sand erosion condition.

Sign in / Sign up

Export Citation Format

Share Document