scholarly journals Actuation Torque Reduction in Parallel Robots Using Joint Compliance

2014 ◽  
Vol 6 (2) ◽  
Author(s):  
Júlia Borràs ◽  
Aaron M. Dollar
Keyword(s):  
Optimization Procedure ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Operating Conditions ◽  
Compliant Joints ◽  
Force Direction ◽  
Force Reduction ◽  
External Forces ◽  
Stewart Gough Platform ◽  
Actuated Joints

This work studies in detail how the judicial application of compliance in parallel manipulators can produce manipulators that require significantly lower actuator effort within a range of desired operating conditions. We propose a framework that uses the Jacobian matrices of redundant parallel manipulators to consider the influence of compliance both in parallel with the actuated joints as well as the passive joints, greatly simplifying previous approaches. We also propose a simple optimization procedure to maximize the motor force reduction for desired regions of the workspace and range of external forces. We then apply the method to a Stewart-Gough platform and to a 3-URS (universal rotational and spherical joint) manipulator. Our results show that parallel manipulators with tasks that involve a preferred external force direction, as for instance, big weights in the platform, can see large reductions in actuator effort through the judicial use of compliant joints without significantly losing rigidity.

Jacobian-based stiffness analysis method for parallel manipulators with non-redundant legs

2015 ◽  
Vol 230 (3) ◽  
pp. 341-352 ◽  
Author(s):  
Antonius GL Hoevenaars ◽  
Patrice Lambert ◽  
Just L Herder
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Structural Elements ◽  
Analysis Method ◽  
End Effector ◽  
Stiffness Analysis ◽  
Compliant Joints ◽  
Lower Mobility ◽  
Actuated Joints

Stiffness is an important element in the model of a parallel manipulator. A complete stiffness analysis includes the contributions of joints as well as structural elements. Parallel manipulators potentially include both actuated joints, passive compliant joints, and zero stiffness joints, while a leg may impose constraints on the end-effector in the case of lower mobility parallel manipulators. Additionally, parallel manipulators are often designed to interact with an environment, which means that an external wrench may be applied to the end-effector. This paper presents a Jacobian-based stiffness analysis method, based on screw theory, that effectively considers all above aspects and which also applies to parallel manipulators with non-redundant legs.

scholarly journals Overconstrained Cable-Driven Parallel Manipulators Statics Analysis based on Simplified Static Cable Model

2021 ◽  
Author(s):  
Phan Gia Luan ◽  
Nguyen Truong Thinh
Keyword(s):  
Load Capacity ◽  
Numerical Test ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Cable Model ◽  
Geometric Problem ◽  
Underdetermined System ◽  
Redundant Actuators ◽  
External Forces ◽  
Flexible Cables

Abstract In recent years, cable-driven parallel manipulators (CDPM) become more and more interesting topics of robot researchers due to its outstanding advantages. Unlike traditional parallel robots, CDPMs use many flexible cables in order to connect the robot fixed frame and the moving platform instead of using conventional rigid links. Since cables used in CDPM is very light compared to rigid links, its workspace can be very large. Besides, CDPMs are often enhanced load capacity by adding redundant actuators. They also help to widen the singularity-free workspace of CDPM. On the other hand, the redundant actuators produce the underdetermined system i.e. the system has non-unique solutions. Moreover, the elasticity and bendability of flexible cable caused by self-weight and external forces act on it, resulting in the kinematic problem of CDPMs are no longer related to the geometric problem. Therefore, the system of CDPM become non-linear when the deformation of cable is considered. In this study, we introduce the simplified static cable model and use it to linearize the static model of redundantly actuated CDPM. The algorithm to solve the force distribution problem is proposed in Sect. 4. The static-workspace and the performance of those are analyzed in a numerical test.

scholarly journals Introduction to the special issue: parallel manipulators.

Robotica ◽  
1997 ◽  
Vol 15 (4) ◽  
pp. 353-353
Author(s):  
François Pierrot
Keyword(s):  
North America ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Parallel Mechanisms ◽  
Special Issue ◽  
Industrial Areas

It has been a pleasure for me to arrange this Special Issue of Robotica on Parallel Robots which provides 9 papers from authors from Asia, Oceania, North America and Europe; worldwide research on this topic is proof of the growing interest of both the scientific and the industrial areas of parallel mechanisms. I truly believe that the main reason for this enthusiasm is that parallel mechanisms research extends from theoretical mathematics and kinematics to applied robotics, and even beyond, creating new technological challenges.

Development of Active Rehabilitation Device of Hand Joint

2012 ◽  
Vol 591-593 ◽  
pp. 245-250 ◽  
Author(s):  
Hsi Chuan Huang ◽  
W.H. Kao ◽  
T.S. Wei ◽  
S.Y. Liu ◽  
Y.S. Syu ◽  
...  
Keyword(s):  
Control System ◽  
Embedded System ◽  
Physical Therapists ◽  
Physical Therapist ◽  
Operating Conditions ◽  
Control Technology ◽  
Rehabilitation Process ◽  
Processing Control ◽  
Active Rehabilitation ◽  
External Forces

If the hand joints patients have not been taking autonomic or external force rehabilitation, they might become disabled, even leading the cause ofirreversible disability eventually. Generally speaking, the medical treatment of rehabilitation has been doing by physical therapist by providing patients with external forces rehabilitation assistance as far as we know currently. For the purpose of both of reducing the workload of physical therapists and providing the quantitative data obtained during the rehabilitation process so as for physical therapist’s reference. This research will build an automatic finger stretch and grip control system by using the Human- Machine Interface for operation control. It can be done by physical therapist or physical doctor to set the operating conditions so as to help the patients with their finger joints motion so as to achieve the rehabilitation effect of their fingers. This research is trying to integrate the mechanism and control technology mainly. With regards to the control technology, it uses a micro chip so as to lead the motions of the stretch & grip for finger rehabilitation by a signal processing control servo motor. And its operation interface is using an embedded system along with Visual Studio compiling software so as to touch input the operating conditions. The system operation functions are including single finger joint motion orsynchronized actuation of all fingers and the setting of the cycle numbers. Furthermore, in order to soften the finger tendons so as to promote the rehabilitation effect during the rehabilitation process, the system adds external steam in so as to control the internal temperature & humidity of the rehabilitation box and apparently, the whole finger automatic stretch & grip control system will be better owing to it.

The Motion of Floating Systems: Nonlinear Dynamics in Periodic and Random Waves

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Katrin Ellermann
Keyword(s):  
Dynamical Behavior ◽  
Nonlinear Behavior ◽  
Operating Conditions ◽  
Random Waves ◽  
Multiple Components ◽  
Random Disturbances ◽  
Restoring Forces ◽  
Steady State Responses ◽  
External Forces ◽  
Floating Systems

Floating systems, such as ships, barges, or semisubmersibles, show a dynamical behavior, which is determined by their internal structure and the operating conditions caused by external forces e.g., due to waves and wind. Due to the complexity of the system, which commonly includes coupling of multiple components or nonlinear restoring forces, the response can exhibit inherently nonlinear characteristics. In this paper different models of floating systems are considered. For the idealized case of purely harmonic forcing they all show nonlinear behavior such as subharmonic motion or different steady-state responses at constant operating conditions. The introduction of random disturbances leads to deviations from the idealized case, which may change the overall response significantly. Advantages and limitations of the different mathematical models and the applied numerical techniques are discussed.

Variable geometry wing-box: toward a robotic morphing wing.

2021 ◽  
Author(s):  
Amin Moosavian
Keyword(s):  
Degrees Of Freedom ◽  
Minimum Energy ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Optimal Configuration ◽  
Configuration Design ◽  
Variable Geometry ◽  
Static Characteristics ◽  
Actuation Redundancy ◽  
Wing Box

The ability to vary the geometry of a wing to adapt to different flight conditions can significantly improve the performance of an aircraft. However, the realization of any morphing concept will typically be accompanied by major challenges. Specifically, the geometrical constraints that are imposed by the shape of the wing and the magnitude of the air and inertia loads make the usage of conventional mechanisms inefficient for morphing applications. Such restrictions have served as inspirations for the design of a modular morphing concept, referred to as the Variable Geometry Wing-box (VGW). The design for the VGW is based on a novel class of reconfigurable robots referred to as Parallel Robots with Enhanced Stiffness (PRES) which are presented in this dissertation. The underlying feature of these robots is the efficient exploitation of redundancies in parallel manipulators. There have been three categories identified in the literature to classify redundancies in parallel manipulators: 1) actuation redundancy, 2) kinematic redundancy, and 3) sensor redundancy. A fourth category is introduced here, referred to as 4) static redundancy. The latter entails several advantages traditionally associated only with actuation redundancy, most significant of which is enhanced stiffness and static characteristics, without any form of actuation redundancy. Additionally, the PRES uses the available redundancies to 1) control more Degrees of Freedom (DOFs) than there are actuators in the system, that is, under-actuate, and 2) provide multiple degrees of fault tolerance. Although the majority of the presented work has been tailored to accommodate the VGW, it can be applied to any comparable system, where enhanced stiffness or static characteristics may be desired without actuation redundancy. In addition to the kinematic and the kinetostatic analyses of the PRES, which are developed and presented in this dissertation along with several case-studies, an optimal motion control algorithm for minimum energy actuation is proposed. Furthermore, the optimal configuration design for the VGW is studied. The optimal configuration design problem is posed in two parts: 1) the optimal limb configuration, and 2) the optimal topological configuration. The former seeks the optimal design of the kinematic joints and links, while the latter seeks the minimal compliance solution to their placement within the design space. In addition to the static and kinematic criteria required for reconfigurability, practical design considerations such as fail-safe requirements and design for minimal aeroelastic impact have been included as constraints in the optimization process. The effectiveness of the proposed design, analysis, and optimization is demonstrated through simulation and a multi-module reconfigurable prototype.

Experimental Validation of the Kinematics of a 3PRS Compliant Mechanism for Micromilling

2015 ◽  
Author(s):  
Antonio Ruiz ◽  
Francisco Campa Gomez ◽  
Constantino Roldan-Paraponiaris ◽  
Oscar Altuzarra
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Experimental Validation ◽  
Compliant Mechanism ◽  
Motion Controller ◽  
End Effector ◽  
Compliant Joints ◽  
Hybrid Manipulator ◽  
Compliant Parallel Mechanism ◽  
Actuated Joints

The present work deals with the development of a hybrid manipulator of 5 degrees of freedom for milling moulds for microlenses. The manipulator is based on a XY stage under a 3PRS compliant parallel mechanism. The mechanism takes advantage of the compliant joints to achieve higher repetitiveness, smoother motion and a higher bandwidth, due to the high precision demanded from the process, under 0.1 micrometers. This work is focused on the kinematics of the compliant stage of the hybrid manipulator. First, an analysis of the workspace required for the milling of a single mould has been performed, calculating the displacements required in X, Y, Z axis as well as two relative rotations between the tool and the workpiece from a programmed toolpath. Then, the 3PRS compliant parallel mechanism has been designed using FEM with the objective of being stiff enough to support the cutting forces from the micromilling, but flexible enough in the revolution and spherical compliant joints to provide the displacements needed. Finally, a prototype of the 3PRS compliant mechanism has been built, implementing a motion controller to perform translations in Z direction and two rotations. The resulting displacements in the end effector and the actuated joints have been measured and compared with the FEM calculations and with the rigid body kinematics of the 3PRS.

Gröbner basis and resultant method for the forward displacement of 3-DoF planar parallel manipulators in seven-dimensional kinematic space

Robotica ◽  
2015 ◽  
Vol 34 (11) ◽  
pp. 2610-2628 ◽  
Author(s):  
Davood Naderi ◽  
Mehdi Tale-Masouleh ◽  
Payam Varshovi-Jaghargh
Keyword(s):  
Euclidean Space ◽  
Gröbner Basis ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Dimensional Euclidean Space ◽  
Grobner Basis ◽  
Kinematic Space ◽  
Forward Kinematic Problem ◽  
Forward Kinematic

SUMMARYIn this paper, the forward kinematic analysis of 3-degree-of-freedom planar parallel robots with identical limb structures is presented. The proposed algorithm is based on Study's kinematic mapping (E. Study, “von den Bewegungen und Umlegungen,” Math. Ann.39, 441–565 (1891)), resultant method, and the Gröbner basis in seven-dimensional kinematic space. The obtained solution in seven-dimensional kinematic space of the forward kinematic problem is mapped into three-dimensional Euclidean space. An alternative solution of the forward kinematic problem is obtained using resultant method in three-dimensional Euclidean space, and the result is compared with the obtained mapping result from seven-dimensional kinematic space. Both approaches lead to the same maximum number of solutions: 2, 6, 6, 6, 2, 2, 2, 6, 2, and 2 for the forward kinematic problem of planar parallel robots; 3-RPR, 3-RPR, 3-RRR, 3-RRR, 3-RRP, 3-RPP, 3-RPP, 3-PRR, 3-PRR, and 3-PRP, respectively.

Kinematic-, Static- and Workspace Analysis of a 6-P-U-S Parallel Manipulator

2010 ◽  
Author(s):  
Madusudanan Sathia Narayanan ◽  
Sourish Chakravarty ◽  
Hrishi Shah ◽  
Venkat N. Krovi
Keyword(s):  
Structural Design ◽  
Parallel Manipulators ◽  
Type I ◽  
Kinematic Modeling ◽  
Workspace Analysis ◽  
Reaction Forces ◽  
Specific Configuration ◽  
Parallel Kinematic ◽  
Stewart Gough Platform

This paper examines the symbolic kinematic modeling of a general 6-P-U-S (prismatic-universal-spherical) parallel kinematic manipulator (PKM). The base location of actuators has been previously shown to lead to: (i) reduction of the (motor) weight carried by the legs; (ii) elimination of the actuation transmission requirement (through intermediary joints as in the case of the Stewart-Gough platform); and (iii) most-importantly absorption of reaction-forces by the ground. We focus on using the symbolic equations to derive the conditions for type I and II singularities of this class of parallel manipulators. Based on these conditions, this system of equations is specialized to a specific configuration of the platform that has superior structural design and comparatively minimal singularities within its workspace. A series of studies were conducted to investigate the quality of workspace as well as estimate the actuation requirements for a unit payload carried over their workspace using the symbolic Jacobian model for this specialized configuration.

scholarly journals Integration of Operability Framework and Pareto Optimal Front to Calculate Optimal Condition of Ethane Cracking Process

2020 ◽  
pp. 105-113
Author(s):  
M. Farsi
Keyword(s):  
Pareto Front ◽  
Optimal Solution ◽  
Optimization Procedure ◽  
Operating Conditions ◽  
Base Case ◽  
Pareto Optimal ◽  
Multi Objective Optimization ◽  
Pareto Optimal Front ◽  
Multi Objective ◽  
Cracking Process

The main aim of this research is to present an optimization procedure based on the integration of operability framework and multi-objective optimization concepts to find the single optimal solution of processes. In this regard, the Desired Pareto Index is defined as the ratio of desired Pareto front to the Pareto optimal front as a quantitative criterion to analyze the performance of chemical processes. The Desired Pareto Front is defined as a part of the Pareto front that all outputs are improved compared to the conventional operating condition. To prove the efficiency of proposed optimization method, the operating conditions of ethane cracking process is optimized as a base case. The ethylene and methane production rates are selected as the objectives in the formulated multi-objective optimization problem. Based on the simulation results, applying the obtained operating conditions by the proposed optimization procedure on the ethane cracking process improve ethylene production by about 3% compared to the conventional condition.  

Sign in / Sign up

Export Citation Format

Share Document