Influence of Coolant Density on Turbine Blade Film-Cooling With Axial and Compound Shaped Holes

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Axial Angle ◽  
Lift Off ◽  
Compound Angle

Adiabatic film-cooling effectiveness is examined systematically on a typical high pressure turbine blade by varying three critical flow parameters: coolant blowing ratio, coolant-to-mainstream density ratio, and freestream turbulence intensity. Three coolant density ratios 1.0, 1.5, and 2.0 are chosen for this study. The average blowing ration and the turbulence intensity are 1.5% and 10.5%, respectively. Conduction-free pressure sensitive paint (PSP) technique is used to measure film-cooling effectiveness. Foreign gases are used to study the effect of coolant density. Two test blades feature axial angle and 45 deg compound-angle shaped holes on the suction side and pressure side. Both designs have 3 rows of 30 deg radial-angle cylindrical holes around the leading edge region. The inlet and the exit Mach number are 0.27 and 0.44, respectively. Reynolds number based on the exit velocity and blade axial chord length is 750,000. Overall, the compound angle design performs better film coverage that axial angle. Greater coolant-to-mainstream density ratio results in lower coolant-to-mainstream momentum and prevents coolant to lift-off.

Numerical Analysis on the Leading Edge Film Cooling of Bifurcation Holes for Gas Turbine Blade

2021 ◽  
Author(s):  
Zhonghao Tang ◽  
Gongnan Xie ◽  
Honglin Li ◽  
Wenjing Gao ◽  
Chunlong Tan ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Turbulence Models ◽  
Leading Edge ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cylindrical Holes ◽  
Lift Off

Abstract Film cooling performance of the cylindrical film holes and the bifurcated film holes on the leading edge model of the turbine blade are investigated in this paper. The suitability of different turbulence models to predict local and average film cooling effectiveness is validated by comparing with available experimental results. Three rows of holes are arranged in a semi-cylindrical model to simulate the leading edge of the turbine blade. Four different film cooling structures (including a cylindrical film holes and other three different bifurcated film holes) and four different blowing ratios are studied in detail. The results show that the film jets lift off gradually in the leading edge area as the blowing ratio increases. And the trajectory of the film jets gradually deviate from the mainstream direction to the spanwise direction. The cylindrical film holes and vertical bifurcated film holes have better film cooling effectiveness at low blowing ratio while the other two transverse bifurcated film holes have better film cooling effectiveness at high blowing ratio. And the film cooling effectiveness of the transverse bifurcated film holes increase with the increasing the blowing ratio. Additionally, the advantage of transverse bifurcated holes in film cooling effectiveness is more obvious in the downstream region relative to the cylindrical holes. The Area-Average film cooling effectiveness of transverse bifurcated film holes is 38% higher than that of cylindrical holes when blowing ratio is 2.

Enhancement of Film Cooling Performance at the Leading Edge of Turbine Blade

2006 ◽  
Author(s):  
K.-S. Kim ◽  
Youn J. Kim ◽  
S.-M. Kim
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Cylindrical Body ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To enhance the film cooling performance in the vicinity of the turbine blade leading edge, the flow characteristics of the film-cooled turbine blade have been investigated using a cylindrical body model. The inclination of the cooling holes is along the radius of the cylindrical wall and 20 deg relative to the spanwise direction. Mainstream Reynolds number based on the cylinder diameter was 1.01×105 and 0.69×105, and the mainstream turbulence intensities were about 0.2% in both Reynolds numbers. CO2 was used as coolant to simulate the effect of density ratio of coolant-to-mainstream. Furthermore, the effect of coolant flow rates was studied for various blowing ratios of 0.4, 0.7, 1.1, and 1.4, respectively. In experiment, spatially-resolved temperature distributions along the cylindrical body surface were visualized using infrared thermography (IRT) in conjunction with thermocouples, digital image processing, and in situ calibration procedures. This comparison shows the results generated to be reasonable and physically meaningful. The film cooling effectiveness of current measurement (0.29 mm × 0.33 min per pixel) presents high spatial and temperature resolutions compared to other studies. Results show that the blowing ratio has a strong effect on film cooling effectiveness and the coolant trajectory is sensitive to the blowing ratio. The local spanwise-averaged effectiveness can be improved by locating the first-row holes near the second-row holes.

Unsteady Wake and Coolant Density Effects on Turbine Blade Film Cooling Using PSP Technique

2010 ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Shiou-Jiuan Li ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Unsteady Wake ◽  
Lift Off ◽  
Film Cooling Holes

The effect of an unsteady stator wake (simulated by wake rods mounted on a spoke wheel wake generator) on the modeled rotor blade is studied using the Pressure Sensitive Paint (PSP) mass transfer analogy method. Emphasis of the current study is on the mid-span region of the blade. The flow is in the low Mach number (incompressible) regime. The suction (convex) side has simple angled cylindrical film-cooling holes; the pressure (concave) side has compound angled cylindrical film cooling holes. The blade also has radial shower-head leading edge film cooling holes. Strouhal numbers studied range from 0 to 0.36; the exit Reynolds Number based on the axial chord is 530,000. Blowing ratios range from 0.5 to 2.0 on the suction side; 0.5 to 4.0 on the pressure side. Density ratios studied range from 1.0 to 2.5, to simulate actual engine conditions. The convex suction surface experiences film-cooling jet lift-off at higher blowing ratios, resulting in low effectiveness values. The film coolant is found to reattach downstream on the concave pressure surface, increasing effectiveness at higher blowing ratios. Results show deterioration in film cooling effectiveness due to increased local turbulence caused by the unsteady wake, especially on the suction side. Results also show a monotonic increase in film-cooling effectiveness on increasing the coolant to mainstream density ratio.

Influence of Coolant Density on Turbine Blade Platform Film-Cooling

2012 ◽  
Vol 4 (2) ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Mainstream Flow ◽  
Purge Flow

Detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform of a five-blade linear cascade. The parameters chosen were freestream turbulence intensity, upstream stator-rotor purge flow rate, discrete-hole film-cooling blowing ratio, and coolant-to-mainstream density ratio. The measurement technique adopted was temperature sensitive paint (TSP) technique. Two turbulence intensities of 4.2% and 10.5%; three purge flows between the range of 0.25% and 0.75% of mainstream flow rate; three blowing ratios between 1.0 and 1.8; and three density ratios between 1.1 and 2.2 were investigated. Purge flow was supplied via a typical double-toothed stator-rotor seal, whereas the discrete-hole film-cooling was accomplished via two rows of cylindrical holes arranged along the length of the platform. The inlet and the exit Mach numbers were 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 7.5 * 105 based on the exit velocity and chord length of the blade. Results indicated that platform film-cooling effectiveness decreased with turbulence intensity, increased with purge flow rate and density ratio, and possessed an optimum blowing ratio value.

Numerical Evaluation of the Performance of the Sister–Shaped Single–Hole Schemes on Turbine Blade Leading Edge Film Cooling

2015 ◽  
Author(s):  
Siavash Khajehhasani ◽  
Bassam Jubran
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Numerical Evaluation ◽  
Leading Edge ◽  
Lateral Spread ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Hole ◽  
Shaped Hole ◽  
Lift Off

In the present study, a numerical evaluation of the performance of the sister-shaped single-hole (SSSH) schemes (downstream, upstream and up/downstream) on the leading edge of AGTB-B1 high pressure turbine blade cascade is carried out. Simulations are performed at three blowing ratios of 0.7, 1.1 and 1.5. Predicted results are compared to the single cylindrical hole and a 15° forward-diffused shaped hole. The realizable k-ε model combined with the standard wall function is used to model the flow field; wherein, the predicted pressure field was in a good agreement with the available experimental data. At the high blowing ratios of 1.1 and 1.5, a noticeable improvement in the film cooling effectiveness and the lateral spread of the cooling jet has been observed for the upstream and up/downstream SSSH schemes, in particular on the suction side. The downstream SSSH configuration provided almost similar film cooling effectiveness values to that of the forward diffused shaped hole for all blowing ratios on both the pressure and suction sides of the blade. Note that the obtained film cooling effectiveness for the downstream SSSH scheme at high blowing ratios was disappointing in comparison with other SSSH schemes where much higher film cooling effectiveness values were obtained. The mixing of the coolant with the high mainstream flow at the leading edge of the blade is considerably decreased for the upstream and up/downstream SSSH schemes and more adhered coolant to the blade’s surface is observed than with other configurations. Moreover, the jet lift-off is notably diminished for the upstream and up/downstream SSSH compared to other hole geometries.

Experimental Investigation of Film Cooling Effectiveness for a New Shaped Hole at the Leading Edge

2010 ◽  
Author(s):  
T. Elnady ◽  
I. Hassan ◽  
L. Kadem ◽  
T. Lucas
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Local Cooling ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Lift Off

An experimental investigation has been performed to study the film cooling of a smooth expansion exit at the leading edge of a gas turbine vane. A two-dimensional cascade has been employed to measure the cooling performance of the proposed expansion using a transient Thermochromatic Liquid Crystal technique. One row of cylindrical holes, located on the stagnation line, is investigated with two expansion levels at the hole exit, 2d and 4d, in addition to the standard cylindrical exit. The air is injected at 0° and 30° inclination angles with the mainstream direction at four blowing ratios ranging from 1 and 2 and a 0.9 density ratio. The Mach number and the Reynolds number based on the cascade exit velocity and the axial chord are 0.23 and 1.4E5, respectively. The detailed local cooling effectiveness over both the pressure side and the suction side are presented in addition to the lateral-averaged cooling effectiveness. The proposed expansion enhances the coolant distribution over the leading edge, particularly over the suction side. The cooling effectiveness increases with the increase of the blowing ratio due to the decrease in the jet lift-off, hence higher cooling capacity is provided. The complete confrontation between both streams on the 0° inclination angle causes a strong dispersion to the coolant, yielding a significant reduction in the effectiveness.

Influence of Coolant Density on Turbine Blade Platform Film-Cooling

2009 ◽  
Author(s):  
Diganta P. Narzary ◽  
Kuo-Chun Liu ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Flow Rate ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Mainstream Flow ◽  
Purge Flow

Detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform of a five-blade linear cascade. The parameters chosen were — freestream turbulence intensity, upstream stator-rotor purge flow rate, discrete-hole film-cooling blowing ratio, and coolant-to-mainstream density ratio. The measurement technique adopted was temperature sensitive paint (TSP) technique. Two turbulence intensities of 4.2% and 10.5%; three purge flows between the range of 0.25% and 0.75% of mainstream flow rate; three blowing ratios between 1.0 and 2.0; and three density ratios between 1.1 and 2.1 were investigated. Purge flow was supplied via a typical double-toothed stator-rotor seal, whereas the discrete-hole film cooling was accomplished via two rows of cylindrical holes arranged along the length of the platform. The inlet and the exit Mach numbers were 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 7.5*105 based on the exit velocity and chord length of the blade. Results indicated that platform film-cooling effectiveness decreased with turbulence intensity, increased with purge flow rate and density ratio, and possessed an optimum blowing ratio value. The improved effectiveness with density ratio was further validated by the pressure sensitive paint (PSP) technique.

Assessment of a Double Hole Film Cooling Geometry Using S-PIV and PSP

2013 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Charles P. Brown ◽  
Weston V. Harmon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Three Dimensional ◽  
Field Measurements ◽  
Secondary Flows ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Hole Geometry ◽  
Compound Angle

A novel, double hole film cooling configuration is investigated as an alternative to traditional cylindrical and fanshaped, laidback holes. This experimental investigation utilizes a Stereo-Particle Image Velocimetry (S-PIV) to quantitatively assess the ability of the proposed, double hole geometry to weaken or mitigate the counter-rotating vortices formed within the jet structure. The three-dimensional flow field measurements are combined with surface film cooling effectiveness measurements obtained using Pressure Sensitive Paint (PSP). The double hole geometry consists of two compound angle holes. The inclination of each hole is θ = 35°, and the compound angle of the holes is β = ± 45° (with the holes angled toward one another). The simple angle cylindrical and shaped holes both have an inclination angle of θ = 35°. The blowing ratio is varied from M = 0.5 to 1.5 for all three film cooling geometries while the density ratio is maintained at DR = 1.0. Time averaged velocity distributions are obtained for both the mainstream and coolant flows at five streamwise planes across the fluid domain (x/d = −4, 0, 1, 5, and 10). These transverse velocity distributions are combined with the detailed film cooling effectiveness distributions on the surface to evaluate the proposed double hole configuration (compared to the traditional hole designs). The fanshaped, laidback geometry effectively reduces the strength of the kidney-shaped vortices within the structure of the jet (over the entire range of blowing ratios considered). The three-dimensional velocity field measurements indicate the secondary flows formed from the double hole geometry strengthen in the plane perpendicular to the mainstream flow. At the exit of the double hole geometry, the streamwise momentum of the jets is reduced (compared to the single, cylindrical hole), and the geometry offers improved film cooling coverage. However, moving downstream in the steamwise direction, the two jets form a single jet, and the counter-rotating vortices are comparable to those formed within the jet from a single, cylindrical hole. These strong secondary flows lift the coolant off the surface, and the film cooling coverage offered by the double hole geometry is reduced.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Sign in / Sign up

Export Citation Format

Share Document