Effect of Rotation on Detailed Heat Transfer Distribution for Various Rib Geometries in Developing Channel Flow

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
Justin A. Lamont ◽  
Srinath V. Ekkad ◽  
Mary Anne Alvin
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Turbine Blades ◽  
Layer Growth ◽  
Entrance Region ◽  
Detailed Knowledge ◽  
Transfer Coefficients ◽  
Enhance Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Rib Turbulators

The effects of Coriolis force and centrifugal buoyancy have a significant impact on heat transfer behavior inside rotating internal serpentine coolant channels for turbine blades. Due to the complexity of added rotation inside such channels, detailed knowledge of the heat transfer will greatly enhance the blade designer's ability to predict hot spots so coolant may be distributed more effectively. The effects of high rotation numbers are investigated on the heat transfer distributions for different rib types in near entrance and entrance region of the channels. It is important to determine the actual enhancement derived from turbulating channel entrances where heat transfer is already high due to entrance effects and boundary layer growth. A transient liquid crystal technique is used to measure detailed heat transfer coefficients (htc) for a rotating, short length, radially outward coolant channel with rib turbulators. Different rib types such as 90 deg, W, and M-shaped ribs are used to roughen the walls to enhance heat transfer. The channel Reynolds number is held constant at 12,000 while the rotation number is increased up to 0.5. Results show that in the near entrance region, the high performance W and M-shaped ribs are just as effective as the simple 90 deg ribs in enhancing heat transfer. The entrance effect in the developing region causes significantly high baseline heat transfer coefficients thus reducing the effective of the ribs to further enhance heat transfer. Rotation causes increase in heat transfer on the trailing side, while the leading side remains relatively constant limiting the decrement in leading side heat transfer. For all rotational cases, the W and M-shaped ribs show significant effect of rotation with large differences between leading and trailing side heat transfer.

scholarly journals Effect of Discrete Ribs on Heat Transfer and Friction Inside Narrow Rectangular Cross Section Cooling Passage of Gas Turbine Blade

2021 ◽  
Vol 10 (6) ◽  
pp. 192-209
Author(s):  
Karthik Krishnaswamy ◽  
◽  
Srikanth Salyan ◽  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Hydraulic Diameter ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Cooling Passage

The performance of a gas turbine during the service life can be enhanced by cooling the turbine blades efficiently. The objective of this study is to achieve high thermohydraulic performance (THP) inside a cooling passage of a turbine blade having aspect ratio (AR) 1:5 by using discrete W and V-shaped ribs. Hydraulic diameter (Dh) of the cooling passage is 50 mm. Ribs are positioned facing downstream with angle-of-attack (α) of 30° and 45° for discrete W-ribs and discerte V-ribs respectively. The rib profiles with rib height to hydraulic diameter ratio (e/Dh) or blockage ratio 0.06 and pitch (P) 36 mm are tested for Reynolds number (Re) range 30000-75000. Analysis reveals that, area averaged Nusselt numbers of the rib profiles are comparable, with maximum difference of 6% at Re 30000, which is within the limits of uncertainty. Variation of local heat transfer coefficients along the stream exhibited a saw tooth profile, with discrete W-ribs exhibiting higher variations. Along spanwise direction, discrete V-ribs showed larger variations. Maximum variation in local heat transfer coefficients is estimated to be 25%. For experimented Re range, friction loss for discrete W-ribs is higher than discrete-V ribs. Rib profiles exhibited superior heat transfer capabilities. The best Nu/Nuo achieved for discrete Vribs is 3.4 and discrete W-ribs is 3.6. In view of superior heat transfer capabilities, ribs can be deployed in cooling passages near the leading edge, where the temperatures are very high. The best THPo achieved is 3.2 for discrete V-ribs and 3 for discrete W-ribs at Re 30000. The ribs can also enhance the power-toweight ratio as they can produce high thermohydraulic performances for low blockage ratios.

Optimization of Vortex Promoter Parameters to Enhance Heat Transfer Rate in Electronic Equipment

2019 ◽  
Vol 12 (2) ◽  
Author(s):  
Ece Aylı ◽  
Özgür Bayer
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Maximum Temperature ◽  
Transfer Coefficients ◽  
Enhance Heat Transfer ◽  
Distance Ratio ◽  
Heat Transfer Coefficients ◽  
Optimization Study ◽  
Finned Surface ◽  
Lower Temperature

Abstract In this paper, optimization of the location and the geometry of a vortex promoter located above in a finned surface in a channel with eight heat sources is investigated for a Reynolds number of 12,500 < Re < 27,700. Heat transfer rates and the corresponding Nusselt number distributions are studied both experimentally and numerically using different vortex promoter geometries (square, circular, and triangular) in different locations to illustrate the effect of vortex promoter on the fluid flow. Optimization study considered a range of following parameters: blockage ratio of 0.30 < (y/C) < 0.45 and interpromoter distance ratio of 0.2277 < (x/L) < 0.3416. Results show that fins over which rectangular and circular promoters are integrated perform better in enhancing the heat transfer. According to the numerical and experimental results, higher blockage ratios cause significantly higher heat transfer coefficients. According to the observations, as the interpromoter distances increase, shedding gains strength, and more turbulence is created. All vortex promoters enhance heat transfer resulting in lower temperature values on the finned surface for different (y/C) and (x/L) values and Reynolds numbers. The use of promoters enhances the heat transfer, and the decrease in the maximum temperature values is recorded on the finned surface changing between 15% and 27%. The biggest decrease in maximum surface temperature value is 500 K–364 K and observed in circular promoter case with (y/C) = 0.43, (x/L) = 0.3416, and Reynolds numbers of 22,200.

An Analytical Study of the Optimized Performance of an Impingement Heat Sink

2004 ◽  
Vol 126 (4) ◽  
pp. 528-534 ◽  
Author(s):  
S. B. Sathe ◽  
B. G. Sammakia
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
High Performance ◽  
Cross Flow ◽  
High Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
High Heat Transfer ◽  
Flow Through

The results of a study of a new and unique high-performance air-cooled impingement heat sink are presented. An extensive numerical investigation of the heat sink performance is conducted and is verified by experimental data. The study is relevant to cooling of high-power chips and modules in air-cooled environments and applies to workstations or mainframes. In the study, a rectangular jet impinges on a set of parallel fins and then turns into cross flow. The effects of the fin thickness, gap nozzle width and fin shape on the heat transfer and pressure drop are investigated. It is found that pressure drop is reduced by cutting the fins in the central impingement zone without sacrificing the heat transfer due to a reduction in the extent of the stagnant zone. A combination of fin thicknesses of the order of 0.5 mm and channel gaps of 0.8 mm with appropriate central cutout yielded heat transfer coefficients over 1500 W/m2 K at a pressure drop of less than 100 N/m2, as is typically available in high-end workstations. A detailed study of flow-through heat sinks subject to the same constraints as the impingement heat sink showed that the flow-through heat sink could not achieve the high heat transfer coefficients at a low pressure drop.

Simulation of Heat Transfer From Flow With High Free-Stream Turbulence to Turbine Blades

1997 ◽  
Vol 119 (2) ◽  
pp. 284-291 ◽  
Author(s):  
E. Fridman
Keyword(s):  
Heat Transfer ◽  
Free Stream ◽  
Turbine Blades ◽  
Plate Boundary ◽  
Transfer Coefficients ◽  
Relaxation Length ◽  
Free Stream Turbulence ◽  
Heat Transfer Coefficients ◽  
High Level ◽  
Flat Plate Boundary Layer

The present investigation is devoted to one of the most difficult problems in the gas turbine industry: predicting the heat transfer to turbine blades. It is known that one of the important factors that affects heat transfer coefficients is a significant level of turbulence in the flow that surrounds a turbine blade. The influence of free-stream turbulence on heat transfer coefficients for a flat plate boundary layer with zero pressure gradient or in the vicinity of the stagnation point of a circular cylinder is investigated numerically. An algebraic relaxation-length model of turbulence is applied in order to simulate real situations in flows with a high level of free-stream turbulence. The results, temperature and velocity profiles, and heat transfer and drag coefficients, are compared with available experimental data. The proposed method is recommended for practical calculations of heat transfer coefficients on turbine blades.

Laminar and Transitional Boundary Layer Structures in Accelerating Flow With Heat Transfer

1986 ◽  
Vol 108 (1) ◽  
pp. 116-123 ◽  
Author(s):  
K. Rued ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Pressure Gradients ◽  
Transfer Coefficients ◽  
Gas Turbine Blades ◽  
Heat Transfer Coefficients ◽  
Layer Structures ◽  
Flow Heat

The accurate prediction of heat transfer coefficients on cooled gas turbine blades requires consideration of various influence parameters. The present study continues previous work with special efforts to determine the separate effects of each of several parameters important in turbine flow. Heat transfer and boundary layer measurements were performed along a cooled flat plate with various freestream turbulence levels (Tu = 1.6−11 percent), pressure gradients (k = 0−6 × 10−6), and cooling intensities (Tw/T∞ = 1.0−0.53). Whereas the majority of previously available results were obtained from adiabatic or only slightly heated surfaces, the present study is directed mainly toward application on highly cooled surfaces as found in gas turbine engines.

Heat Transfer Augmentation in a Rectangular Channel With Slit Rib-Turbulators on Two Opposite Walls

1997 ◽  
Vol 119 (3) ◽  
pp. 617-623 ◽  
Author(s):  
Jenn-Jiang Hwang ◽  
Tong-Miin Liou
Keyword(s):  
Heat Transfer ◽  
Rectangular Channel ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Open Area ◽  
Transfer Coefficients ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients ◽  
Ribbed Channel ◽  
Rib Turbulators

The effect of slit ribs on heat transfer and friction in a rectangular channel is investigated experimentally. The slit ribs are arranged in-line on two opposite walls of the channel. Three rib open-area ratios (β = 24, 37, and 46 percent), three rib pitch-to-height ratios (Pi/H = 10, 20, and 30), and two rib height-to-channel hydraulic diameter ratios (H/De = 0.081, and 0.162) are examined. The Reynolds number ranges from 10,000 to 50,000. Laser holographic interferometry is employed to measure the local heat transfer coefficients of the ribbed wall quantitatively, and observe the flow over the ribbed wall qualitatively. The results show that the slit rib has an advantage of avoiding “hot spots.” In addition, the heat transfer performance of the slit-ribbed channel is much better than that of the solid-ribbed channel. Semi-empirical correlations for friction and heat transfer are developed to account for rib spacings and open-area ratios. These correlations may be used in the design of turbine blade cooling passages.

scholarly journals Verification of Thermal Models of Internally Cooled Gas Turbine Blades

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Igor Shevchenko ◽  
Nikolay Rogalev ◽  
Andrey Rogalev ◽  
Andrey Vegera ◽  
Nikolay Bychkov
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Heat Removal ◽  
Leading Edge ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Transfer Coefficients ◽  
Single Experiment ◽  
Heat Transfer Coefficients

Numerical simulation of temperature field of cooled turbine blades is a required element of gas turbine engine design process. The verification is usually performed on the basis of results of test of full-size blade prototype on a gas-dynamic test bench. A method of calorimetric measurement in a molten metal thermostat for verification of a thermal model of cooled blade is proposed in this paper. The method allows obtaining local values of heat flux in each point of blade surface within a single experiment. The error of determination of local heat transfer coefficients using this method does not exceed 8% for blades with radial channels. An important feature of the method is that the heat load remains unchanged during the experiment and the blade outer surface temperature equals zinc melting point. The verification of thermal-hydraulic model of high-pressure turbine blade with cooling allowing asymmetrical heat removal from pressure and suction sides was carried out using the developed method. An analysis of heat transfer coefficients confirmed the high level of heat transfer in the leading edge, whose value is comparable with jet impingement heat transfer. The maximum of the heat transfer coefficients is shifted from the critical point of the leading edge to the pressure side.

Calculation of Heat Transfer Coefficients in Cooled Turbine Cascades

1966 ◽  
Vol 17 (3) ◽  
pp. 253-268 ◽  
Author(s):  
H. D. Harris ◽  
R. E. Luxton
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flow ◽  
Turbine Blades ◽  
Order Estimate ◽  
Transfer Coefficients ◽  
Local Pressure ◽  
Heat Transfer Coefficients ◽  
Blade Cooling

SummaryAn approximate method is presented for the calculation of heat transfer rates to cooled turbine blades. The method is based on a combination and extension of methods which have been developed in recent years for the calculation of the skin friction and heat transfer coefficients on wings in high speed flight. The use of the method is demonstrated by application to a specific cascade for which an experimental determination of overall heat transfer coefficient is known. Very close agreement with the experimental results is found over the range of Reynolds number tested. The calculated distribution of local heat transfer coefficient indicates that local pressure gradients have a marked effect on the heat transfer. A first-order estimate of the effect of blade cooling on the rate of mass flow through a blade passage shows that an increase of the order of one per cent in the mass flow rate may be obtained by a reasonable degree of blade cooling.

Calculation of Heat Transfer to Convection-Cooled Gas Turbine Blades

1985 ◽  
Vol 107 (3) ◽  
pp. 620-627 ◽  
Author(s):  
W. Rodi ◽  
G. Scheuerer
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Complex Nature ◽  
Surface Boundary ◽  
Transfer Coefficients ◽  
Free Stream Turbulence ◽  
Gas Turbine Blades ◽  
Heat Transfer Coefficients

A mathematical model is presented for calculating the external heat transfer coefficients around gas turbine blades. The model is based on a finite-difference procedure for solving the boundary-layer equations which describe the flow and temperature field around the blades. The effects of turbulence are simulated by a low-Reynolds number version of the k-ε turbulence model. This allows calculation of laminar and transitional zones and also the onset of transition. Applications of the calculation method are presented to turbine-blade situations which have recently been investigated experimentally. Predicted and measured heat transfer coefficients are compared and good agreement with the data is observed. This is true especially for the pressure-surface boundary layer which is of a rather complex nature because it remains in a transitional state over the full blade length. The influence of various flow phenomena like laminar-turbulent transition and of the boundary conditions (pressure gradient, free-stream turbulence) on the predicted heat transfer rates is discussed.

scholarly journals Heat Transfer Phenomena in Gas Turbines

1980 ◽  
Author(s):  
J. R. Taylor
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Gas Turbine Engine ◽  
Transfer Coefficients ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients

A discussion of the problems encountered in prediction of heat transfer in the turbine section of a gas turbine engine is presented. Areas of current gas turbine engine is presented. Areas of current concern to designers where knowledge is deficient or lacking are elucidated. Consideration is given to methods and problems associated with determination of heat transfer coefficients, external gas temperatures, and, where applicable, film cooling effectiveness. The paper is divided into parts dealing with turbine airfoil heat transfer, endwall heat transfer, and heat transfer in the internal cavities of cooled turbine blades. Recent literature dealing with these topics is listed.

Sign in / Sign up

Export Citation Format

Share Document