Vaned Diffuser Induced Impeller Blade Vibrations in a High-Speed Centrifugal Compressor

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Armin Zemp ◽  
Reza S. Abhari
Keyword(s):  
Centrifugal Compressor ◽  
Potential Field ◽  
High Speed ◽  
Forced Response ◽  
Dynamic Strain ◽  
Gap Size ◽  
Damping Properties ◽  
Vaned Diffuser ◽  
Unsteady Fluid ◽  
Radial Gap

Blade failure in turbomachinery is frequently caused by an excessive resonant response. Forced response of the blades typically originates from unsteady fluid structure interactions. This paper presents the experimental and computational results of a research effort focusing on the blade forced response in a high-speed centrifugal compressor caused by the downstream vaned diffuser. The potential field from the downstream vaned diffuser acts as an unsteady impeller relative circumferentially nonuniform disturbance. In this work the effect of varying the radial gap between impeller exit and diffuser vane leading edges was examined. Dynamic strain gauges, which were installed on the blade surfaces, were used to measure the forced response levels of the blades and to estimate the damping properties for different compressor operating conditions and vaneless gap dimensions. Unsteady fluid flow simulations were used to quantify the forcing function acting on the compressor blades due to impeller-diffuser interaction. The time-resolved blade pressure distribution showed the temporal evolution of the dynamic load on the blade surface caused by the diffuser's potential field. The magnitude of the vibratory stress levels was found to depend on the radial gap size, the blade damping properties, and on the compressor operating point. The variation of the radial gap size resulted in a shift of the impeller-diffuser interaction zone towards the main blade leading edge by up to 5% of the streamwise location.

Vaned Diffuser Induced Impeller Blade Vibrations in a High-Speed Centrifugal Compressor

2012 ◽  
Author(s):  
Armin Zemp ◽  
Reza S. Abhari
Keyword(s):  
Centrifugal Compressor ◽  
Potential Field ◽  
High Speed ◽  
Forced Response ◽  
Dynamic Strain ◽  
Gap Size ◽  
Damping Properties ◽  
Vaned Diffuser ◽  
Unsteady Fluid ◽  
Radial Gap

Blade failure in turbomachinery is frequently caused by an excessive resonant response. Forced response of the blades typically originates from unsteady fluid structure interactions. This paper presents the experimental and computational results of a research effort focusing on the blade forced response in a high-speed centrifugal compressor caused by the downstream vaned diffuser. The potential field from the downstream vaned diffuser acts as an unsteady impeller relative circumferentially nonuniform disturbance. In this work the effect of varying the radial gap between impeller exit and diffuser vane leading edges was examined. Dynamic strain gauges, which were installed on the blade surfaces, were used to measure the forced response levels of the blades and to estimate the damping properties for different compressor operating conditions and vane-less gap dimensions. Unsteady fluid flow simulations were used to quantify the forcing function acting on the compressor blades due to impeller-diffuser interaction. The time-resolved blade pressure distribution showed the temporal evolution of the dynamic load on the blade surface caused by the diffuser’s potential field. The magnitude of the vibratory stress levels was found to depend on the radial gap size, the blade damping properties and on the compressor operating point. The variation of the radial gap size resulted in a shift of the impeller-diffuser interaction zone towards the main blade leading edge by up to 5% of the stream-wise location.

A Numerical Study on Performances of Centrifugal Compressor Stages With Different Radial Gaps

2000 ◽  
Author(s):  
K. Sato ◽  
L. He
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Numerical Study ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Vaned Diffuser ◽  
Navier Stokes Equations ◽  
Performance Predictions ◽  
Radial Gap

A numerical study of 3D unsteady flows in centrifugal compressor stages solving the Navier-Stokes equations is presented. The emphasis is on the effect of the radial gap between blade rows on the aerodynamic performance. In the numerical tests, Krain’s centrifugal impeller was combined with a DCA (Double Circular Arc) type radial vaned diffuser. The compressor stages with three settings of radial gap ranging from 5 to 15 percent of the impeller trailing edge radius are configured and unsteady flow simulations are carried out to compare the time-averaged efficiencies. The performance predictions show that the efficiency is deteriorated if the radial gap between blade rows is reduced with intensified blade row interaction, which is in contradiction to the general trend for axial compressor stages. In the centrifugal compressors tested, wake chopping by diffuser vanes, which usually benefits efficiency in axial compressor stages, causes unfavourable wake compression through the diffuser passages to deteriorate the efficiency.

Unsteady Computational Fluid Dynamics Investigation on Inlet Distortion in a Centrifugal Compressor

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Armin Zemp ◽  
Albert Kammerer ◽  
Reza S. Abhari
Keyword(s):  
Centrifugal Compressor ◽  
Temporal Evolution ◽  
Flow Distribution ◽  
Forced Response ◽  
Inlet Section ◽  
Flow Distortion ◽  
Inlet Flow ◽  
Inlet Distortion ◽  
Forcing Function ◽  
Unsteady Fluid

Blade failure in turbomachinery is frequently caused by an excessive resonant response. Forced response of the blades originates from unsteady fluid structure interactions as conditioned in the inlet section by duct bends, struts, or inlet guide vanes. This paper presents the computational part of a research effort that focuses on the blade forced response in a centrifugal compressor. Unsteady fluid flow simulations are used to quantify the forcing function acting on the compressor blades due to inlet flow distortion. The measured inlet flow distribution is applied as inlet boundary conditions in the computation. The unsteady investigation provided the temporal evolution of the distorted flow through the compressor. The time-resolved blade pressure distribution showed the temporal evolution of the dynamic load on the blade surface caused by the inlet distortion. The results suggest that the forcing function is most sensitive in the leading edge region due to inlet angle variations. Toward the impeller stability line the increase in incidence caused separation on the suction side of the main blade and therefore considerably altered the amplitude and the phase angle of the unsteadiness. The investigation of the effect of idealizing the inlet flow distribution on the forcing function showed an increase in the peak amplitude of approximately 30% compared with the actual inlet flow distribution.

Unsteady CFD Investigation on Inlet Distortion in a Centrifugal Compressor

2008 ◽  
Author(s):  
Armin Zemp ◽  
Albert Kammerer ◽  
Reza S. Abhari
Keyword(s):  
Centrifugal Compressor ◽  
Temporal Evolution ◽  
Flow Distribution ◽  
Forced Response ◽  
Inlet Section ◽  
Flow Distortion ◽  
Inlet Flow ◽  
Inlet Distortion ◽  
Forcing Function ◽  
Unsteady Fluid

Blade failure in turbomachinery is frequently caused by an excessive resonant response. Forced response of the blades originates from unsteady fluid structure interactions as conditioned in the inlet section by duct bends, struts or inlet guide vanes. This paper presents the computational part of a research effort that focuses on the blade forced response in a centrifugal compressor. Unsteady fluid flow simulations are used to quantify the forcing function acting on the compressor blades due to inlet flow distortion. The measured inlet flow distribution is applied as inlet boundary conditions in the computation. The unsteady investigation provided the temporal evolution of the distorted flow through the compressor. The time-resolved blade pressure distribution showed the temporal evolution of the dynamic load on the blade surface caused by the inlet distortion. The results suggest that the forcing function is most sensitive in the leading edge region due to inlet angle variations. Towards the impeller stability line the increase in incidence caused separation on the suction side of the main blade and therefore considerably altered the amplitude and the phase angle of the unsteadiness. The investigation of the effect of idealizing the inlet flow distribution on the forcing function showed an increase of the peak amplitude of approximately 30% compared to the actual inlet flow distribution.

Centrifugal Compressor Inlet Guide Vanes for Increased Surge Margin

1991 ◽  
Vol 113 (4) ◽  
pp. 696-702 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
System Stability ◽  
Negative Slope ◽  
Vaned Diffuser ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Surge Margin ◽  
Compressor Inlet ◽  
Surge Line

This paper describes the results of compressor rig testing with a moderately high specific speed, high inducer Mack number, single-stage centrifugal compressor, with a vaned diffuser, and adjustable inlet guide vanes (IGVs). The results showed that the high-speed surge margin was considerably extended by the regulation of the IGVs, even though the vaned diffuser was apparently operating stalled. Simplified one-dimensional analysis of the impeller and diffuser performances indicated that at inducer tip Mach numbers approaching and exceeding unity, the high-speed surge line was triggered by inducer stall. Also, IGV regulation increased impeller stability. This permitted the diffuser to operate stalled, providing the net compression system stability remained on a negative slope.

Aerodynamic Optimization Design of Vaned Diffusers for the 100 kW Micro Gas Turbine’s Centrifugal Compressor

2008 ◽  
Author(s):  
Guang Xi ◽  
Zhiheng Wang ◽  
Chunmei Zhang ◽  
Minjian Yuan
Keyword(s):  
Centrifugal Compressor ◽  
Surrogate Model ◽  
High Speed ◽  
Optimization Design ◽  
Performance Test ◽  
Three Dimensional ◽  
Centrifugal Impeller ◽  
Aerodynamic Optimization ◽  
Vaned Diffuser ◽  
Practical Engineering

In this paper the design optimization of vaned diffuser for the 100kW microturbine’s centrifugal compressor is carried out. The forward-loaded and the conventional airfoil diffusers are respectively redesigned based on the surrogate model and the three dimensional viscous flow analyses. The objective of the optimization is to redesign the diffuser that assures, for a given operating condition of the centrifugal impeller, the stage isentropic efficiency to be highest. Using the surrogate model the optimization process is accelerated and the 3D flow analysis’s application to the practical engineering design is efficiently realized. To validate the optimization result, the compressor stage performance test is performed on a high speed centrifugal compressor test rig with one original diffuser and its redesigned, respectively.

scholarly journals Experimental Investigation of Unsteady Flow Phenomena in a Centrifugal Compressor Vaned Diffuser of Variable Geometry

1999 ◽  
Vol 121 (4) ◽  
pp. 763-771 ◽  
Author(s):  
F. Justen ◽  
K. U. Ziegler ◽  
H. E. Gallus
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Fluctuations ◽  
Suction Side ◽  
Front Wall ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Impeller Outlet ◽  
Flow Phenomena ◽  
Radial Gap

The behavior of vaned radial diffusers is generally considered to be due to the flow phenomena in the vaneless and the semi-vaned space in the diffuser inlet region. Even considering unsteady aspects, the adjacent diffuser channel is regarded as less important. The flat wedge vaned diffuser of the centrifugal compressor stage investigated allows an independent continuous adjustment of the diffuser vane angle and the radial gap between impeller outlet and diffuser vane inlet, so that information about the importance of these geometric parameters can be obtained. The time-dependent pressure distribution on the diffuser front wall and on the suction and pressure surfaces of the diffuser vanes reveal that in the semi-vaned space mainly the region near the vane suction side is influenced by the unsteady impeller-diffuser interaction. Downstream in the diffuser channel the unsteadiness does not decay. Here, pressure fluctuations are appearing that are distinctly higher than the pressure fluctuations in the vaneless space. An estimation of the influence of the unsteadiness on the operating performance of the centrifugal compressor stage is made by measurements at choke and surge limit for different diffuser geometries.

Large Eddy Simulation for a Deep Surge Cycle in a High-Speed Centrifugal Compressor With Vaned Diffuser

2015 ◽  
Vol 137 (10) ◽  
Author(s):  
Ibrahim Shahin ◽  
Mohamed Gadala ◽  
Mohamed Alqaradawi ◽  
Osama Badr
Keyword(s):  
High Pressure ◽  
Large Eddy Simulation ◽  
Centrifugal Compressor ◽  
Pressure Fluctuation ◽  
High Speed ◽  
Computational Study ◽  
Mean Flow ◽  
Vaned Diffuser ◽  
Eddy Simulation ◽  
Large Eddy

This paper presents a computational study for a high-speed centrifugal compressor stage with a design pressure ratio equal to 4, the stage consisting of a splittered unshrouded impeller and a wedged vaned diffuser. The aim of this paper is to investigate numerically the modifications of the flow structure during a surge cycle. The investigations are based on the results of unsteady three-dimensional, compressible flow simulations, using large eddy simulation (LES) model. Instantaneous and mean flow field analyses are presented in the impeller inducer and in the vaned diffuser region through one surge cycle time intervals. The computational data compare favorably with the measured data, from the literature, for the same compressor and operational point. The surge event phases are well detected inside the impeller and diffuser. The time-averaged loading on the impeller main blade is maximum near the trialing edge and near the tip. The amplitude of the unsteady pressure fluctuation is maximum for the flow reversal condition and reaches values up to 70% of the dynamic pressure. The diffuser vane exhibits high-pressure fluctuation from the vane leading edge to 50% of the chord length. High-pressure fluctuation is detected during the forward flow recovery condition as a result of the shock wave that moves toward the diffuser outlet.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications, bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly-loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a preproduction, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without the bleed flow, the prestall behavior is dominated by short-wavelength disturbances, or so called “spikes,” in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at the impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long-wavelength modal prestall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to the bleed flow and yielding a one point increase in adiabatic compressor efficiency.

Sign in / Sign up

Export Citation Format

Share Document