The Effect of Coolant Injection on the Endwall Flow of a High Pressure Turbine

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Jonathan Ong ◽  
Robert J. Miller ◽  
Sumiu Uchida
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Penetration Depth ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Leakage Flow ◽  
Speed Test ◽  
Coolant Injection

This paper presents a study of the effects of two types of hub coolant injection on the rotor of a high pressure gas turbine stage. The first involves the leakage flow from the hub cavity into the mainstream. The second involves a deliberate injection of coolant from a row of angled holes from the edge of the stator hub. The aim of this study is to improve the distribution of the injected coolant on the rotor hub wall. To achieve this, it is necessary to understand how the coolant and leakage flows interact with the rotor secondary flows. The first part of the paper shows that the hub leakage flow is entrained into the rotor hub secondary flow and the negative incidence of the leakage strengthens the secondary flow and increases its penetration depth. Three-dimensional unsteady calculations were found to agree with fast response pressure probe measurements at the rotor exit of a low speed test turbine. The second part of the paper shows that increasing the injected coolant swirl angle reduced the secondary flow penetration depth, improves the coolant distribution on the rotor hub, and improves stage efficiency. Most of the coolant however, was still found to be entrained into the rotor secondary flow.

The Effect of Coolant Injection on the Endwall Flow of a High Pressure Turbine

2006 ◽  
Author(s):  
Jonathan H. P. Ong ◽  
Robert J. Miller ◽  
Sumiu Uchida
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Penetration Depth ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Leakage Flow ◽  
Speed Test ◽  
Coolant Injection

This paper presents a study of the effects of two types of hub coolant injection on the rotor of a high pressure gas turbine stage. The first involves the leakage flow from the hub cavity into the mainstream. The second involves a deliberate injection of coolant from a row of angled holes from the edge of the stator hub. The aim of this study is to improve the distribution of the injected coolant on the rotor hub wall. To achieve this, it is necessary to understand how the coolant and leakage flows interact with the rotor secondary flows. The first part of the paper shows that the hub leakage flow is entrained into the rotor hub secondary flow and the negative incidence of the leakage strengthens the secondary flow and increases its penetration depth. Three dimensional unsteady calculations were found to agree with fast response pressure probe measurements at the rotor exit of a low speed test turbine. The second part of the paper shows that increasing the injected coolant swirl angle reduced the secondary flow penetration depth, improves the coolant distribution on the rotor hub and improves stage efficiency. Most of the coolant however, was still found to be entrained into the rotor secondary flow.

Blade Row Interaction in a One and a Half Stage Transonic Turbine Focusing on Three Dimensional Effects: Part II—Clocking Effects

2008 ◽  
Author(s):  
O. Schennach ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani ◽  
J. Woisetschla¨ger
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Three Dimensional ◽  
Field Measurements ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three dimensional flow field downstream of the high pressure turbine for different vane clocking positions. To give an overview of the time averaged flow field, measurements by means of a pneumatic five hole probe were performed upstream and downstream of the second stator. Furthermore in this planes additional unsteady measurements were carried out with Laser Doppler Velocimetry in order to record rotor phase resolved velocity, flow angle and turbulence distributions at two different clocking positions. In the measurement plane upstream the second vane the time resolved pressure field has been analyzed by means of a Fast Response Aerodynamic Pressure Probe. The paper shows that the secondary flows of the second vane are significantly modified for different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out.

scholarly journals Incidence Angle and Pitch-Chord Effects on Secondary Flows Downstream of a Turbine Cascade

1992 ◽  
Author(s):  
A. Perdichizzi ◽  
V. Dossena
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Incidence Angle ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Turbine Cascade ◽  
Oil Flow ◽  
Secondary Velocity ◽  
Secondary Flow Field

This paper describes the results of an experimental investigation of the three-dimensional flow downstream of a linear turbine cascade at off-design conditions. The tests have been carried out for five incidence angles from −60 to +35 degrees, and for three pitch-chord ratios: s/c = 0.58,0.73,0.87. Data include blade pressure distributions, oil flow visualizations, and pressure probe measurements. The secondary flow field has been obtained by traversing a miniature five hole probe in a plane located at 50% of an axial chord downstream of the trailing edge. The distributions of local energy loss coefficients, together with vorticity and secondary velocity plots show in detail how much the secondary flow field is modified both by incidence and cascade solidity variations. The level of secondary vorticity and the intensity of the crossflow at the endwall have been found to be strictly related to the blade loading occurring in the blade entrance region. Heavy changes occur in the spanwise distributions of the pitch averaged loss and of the deviation angle, when incidence or pitch-chord ratio is varied.

Three Dimensional Clocking Effects in a One and a Half Stage Transonic Turbine

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Velocity Flow ◽  
Transonic Turbine

This paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three-dimensional aerodynamics of the second vane for different clocking positions. To give an overview of the time-averaged flow field, five-hole probe measurements were performed upstream and downstream of the second stator. Furthermore in these planes additional unsteady measurements were carried out with laser Doppler velocimetry in order to record rotor phase-resolved velocity, flow angle, and turbulence distributions at two different clocking positions. In the planes upstream of the second vane, the time-resolved pressure field has been measured by means of a fast response aerodynamic pressure probe. This paper shows that the secondary flows of the second vane are significantly modified by the different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out, and a 0.6% variation in the second vane loss coefficient has been recorded among the different clocking positions.

Design Optimization of Profiled Endwall With Consideration of Cooling and Rim Seal Flow Effects

2016 ◽  
Author(s):  
Huimin Tang ◽  
Shuaiqiang Liu ◽  
Hualing Luo
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Secondary Flow ◽  
Three Dimensional ◽  
Great Influence ◽  
Optimization Procedure ◽  
Secondary Flows ◽  
High Pressure Turbine ◽  
Operation Condition ◽  
Turbine Performance

Profiled endwall is an effective method to improve aerodynamic performance of turbine. This approach has been widely studied in the past decade on many engines. When automatic design optimisation is considered, most of the researches are usually based on the assumption of a simplified simulation model without considering cooling and rim seal flows. However, many researchers find out that some of the benefits achieved by optimization procedure are lost when applying the high-fidelity geometry configuration. Previously, an optimization procedure has been implemented by integrating the in-house geometry manipulator, a commercial three-dimensional CFD flow solver and the optimization driver, IsightTM. This optimization procedure has been executed [12] to design profiled endwalls for a turbine cascade and a one-and-half stage axial turbine. Improvements of the turbine performance have been achieved. As the profiled endwall is applied to a high pressure turbine, the problems of cooling and rim seal flows should be addressed. In this work, the effects of rim seal flow and cooling on the flow field of two-stage high pressure turbine have been presented. Three optimization runs are performed to design the profiled endwall of Rotor-One with different optimization model to consider the effects of rim flow and cooling separately. It is found that the rim seal flow has a significant impact on the flow field. The cooling is able to change the operation condition greatly, but barely affects the secondary flow in the turbine. The influences of the profiled endwalls on the flow field in turbine and cavities have been analyzed in detail. A significant reduction of secondary flows and corresponding increase of performance are achieved when taking account of the rim flows into the optimization. The traditional optimization mechanism of profiled endwall is to reduce the cross passage gradient, which has great influence on the strength of the secondary flow. However, with considering the rim seal flows, the profiled endwall improves the turbine performance mainly by controlling the path of rim seal flow. Then the optimization procedure with consideration of rim seal flow has also been applied to the design of the profiled endwall for Stator Two.

Incidence Angle and Pitch–Chord Effects on Secondary Flows Downstream of a Turbine Cascade

1993 ◽  
Vol 115 (3) ◽  
pp. 383-391 ◽  
Author(s):  
A. Perdichizzi ◽  
V. Dossena
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Incidence Angle ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Turbine Cascade ◽  
Oil Flow ◽  
Secondary Velocity ◽  
Secondary Flow Field

This paper describes the results of an experimental investigation of the three-dimensional flow downstream of a linear turbine cascade at off-design conditions. The tests have been carried out for five incidence angles from −60 to +35 deg, and for three pitch-chord ratios: s/c = 0.58, 0.73, 0.87. Data include blade pressure distributions, oil flow visualizations, and pressure probe measurements. The secondary flow field has been obtained by traversing a miniature five-hole probe in a plane located at 50 percent of an axial chord downstream of the trailing edge. The distributions of local energy loss coefficients, together with vorticity and secondary velocity plots, show in detail how much the secondary flow field is modified both by incidence and by cascade solidity variations. The level of secondary vorticity and the intensity of the crossflow at the endwall have been found to be strictly related to the blade loading occurring in the blade entrance region. Heavy changes occur in the spanwise distributions of the pitch-averaged loss and of the deviation angle, when incidence or pitch–chord ratio is varied.

A Parametric Study of the Blade Row Interaction in a High Pressure Turbine Stage

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
G. Persico ◽  
P. Gaetani ◽  
C. Osnaghi
Keyword(s):  
High Pressure ◽  
Strong Dependence ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Turbine Stage ◽  
Mixing Rate ◽  
Aerodynamic Pressure ◽  
Blade Row ◽  
Blade Row Interaction

An extensive experimental analysis on the subject of the unsteady periodic flow in a high subsonic high pressure (HP) turbine stage has been carried out at the Laboratorio di Fluidodinamica delle Macchine of the Politecnico di Milano (Italy). In this paper the aerodynamic blade row interaction in HP turbines, enforced by increasing the stator and rotor blade loading and by reducing the stator-rotor axial gap, is studied in detail. The time-averaged three-dimensional flowfield in the stator-rotor gap was investigated by means of a conventional five-hole probe for the nominal (0 deg) and highly positive (+22 deg) stator incidences. The evolution of the viscous flow structures downstream of the stator is presented to characterize the rotor incoming flow. The blade row interaction was evaluated on the basis of unsteady aerodynamic measurements at the rotor exit, performed with a fast-response aerodynamic pressure probe. Results show a strong dependence of the time-averaged and phase-resolved flowfield and of the stage performance on the stator incidence. The structure of the vortex-blade interaction changes significantly as the magnitude of the rotor-inlet vortices increases, and very different residual traces of the stator secondary flows are found downstream of the rotor. On the contrary, the increase in rotor loading enhances the unsteadiness in the rotor secondary flows but has a little effect on the vortex-vortex interaction. For the large axial gap, a reduction of stator-related effects at the rotor exit is encountered when the stator incidence is increased as a result of the different mixing rate within the cascade gap.

scholarly journals Three Dimensional Flow in Radial-Inflow Turbines

1988 ◽  
Author(s):  
M. Zangeneh-Kazemi ◽  
W. N. Dawes ◽  
W. R. Hawthorne
Keyword(s):  
Secondary Flow ◽  
Three Dimensional ◽  
Flow Distribution ◽  
Secondary Flows ◽  
Wake Flow ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Numerical Predictions ◽  
Absolute Flow

The flow through an impeller of a low speed radial-inflow turbine has been analysed using a fully three-dimensional viscous program and good correlations with instantaneous measurements of casing static pressure and exit flow distribution have been obtained. The flow at the exit of the turbine shows a pronounced non-uniformity with a wake region of high absolute flow angle near the casing. The predictions show that the flow is fully attached inside the impeller, while secondary flows can be observed especially in the exducer moving low momentum fluid towards the casing-suction corner. The presence of these secondary flows is discussed with reference to classical secondary flow theory. However, the comparison of measurements and numerical predictions indicate that the wake flow pattern is only partly due to the secondary flow. It is shown that in fact the tip leakage flow also plays a significant role in the wake generation and correspondingly some modelling of the leakage flow is essential in any attempted numerical simulations.

scholarly journals The Design of an Improved Endwall Film-Cooling Configuration

1998 ◽  
Author(s):  
S. Friedrichs ◽  
H. P. Hodson ◽  
W. N. Dawes
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
Large Scale ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Aerodynamic Loss ◽  
Cooling Flow ◽  
High Static Pressure ◽  
Endwall Film Cooling ◽  
Aerodynamic Losses

The endwall film-cooling cooling configuration investigated by Friedrichs et al. (1996, 1997) had in principle sufficient cooling flow for the endwall, but in practice, the redistribution of this coolant by secondary flows left large endwall areas uncooled. This paper describes the attempt to improve upon this datum cooling configuration by redistributing the available coolant to provide a better coolant coverage on the endwall surface, whilst keeping the associated aerodynamic losses small. The design of the new, improved cooling configuration was based on the understanding of endwall film-cooling described by Friedrichs et al. (1996, 1997). Computational fluid dynamics were used to predict the basic flow and pressure field without coolant ejection. Using this as a basis, the above described understanding was used to place cooling holes so that they would provide the necessary cooling coverage at minimal aerodynamic penalty. The simple analytical modelling developed in Friedrichs et al. (1997) was then used to check that the coolant consumption and the increase in aerodynamic loss lay within the limits of the design goal. The improved cooling configuration was tested experimentally in a large scale, low speed linear cascade. An analysis of the results shows that the redesign of the cooling configuration has been successful in achieving an improved coolant coverage with lower aerodynamic losses, whilst using the same amount of coolant as in the datum cooling configuration. The improved cooling configuration has reconfirmed conclusions from Friedrichs et al. (1996, 1997); firstly, coolant ejection downstream of the three-dimensional separation lines on the endwall does not change the secondary flow structures; secondly, placement of holes in regions of high static pressure helps reduce the aerodynamic penalties of platform coolant ejection; finally, taking account of secondary flow can improve the design of endwall film-cooling configurations.

scholarly journals A Summary of the Cooled Turbine Blade Tip Heat Transfer and Film Effectiveness Investigations Performed by Dr. D. E. Metzger

1994 ◽  
Author(s):  
Y. W. Kim ◽  
W. Abdel-Messeh ◽  
J. P. Downs ◽  
F. O. Soechting ◽  
G. D. Steuber ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Convection Heat Transfer ◽  
Secondary Flows ◽  
Test Surface ◽  
Leakage Flow ◽  
Test Technique ◽  
Coolant Injection ◽  
Blade Tip

The clearance gap between the stationary outer air seal and blade tips of an axial turbine allows a clearance gap leakage flow to be driven through the gap by the pressure-to-suction side pressure difference. The presence of strong secondary flows on the pressure side of the airfoil tends to deliver air from the hottest regions of the mainstream to the clearance gap. The blade tip region, particularly near the trailing edge, is very difficult to cool adequately with blade internal coolant flow. In this case, film cooling injection directly onto the blade tip region can be used in an attempt to directly reduce the heat transfer rates from the hot gases in the clearance gap to the blade tip. The present paper is intended as a memorial tribute to the late Professor Darryl E. Metzger who has made significant contributions in this particular area over the past decade. A summary of this work is made to present the results of his more recent experimental work that has been performed to investigate the effects of film coolant injection on convection heat transfer to the turbine blade tip for a variety of tip shapes and coolant injection configurations. Experiments are conducted with blade tip models that are stationary relative to the simulated outer air seal based on the result of earlier works that found the leakage flow to be mainly a pressure-driven flow which is related strongly to the airfoil pressure loading distribution and only weakly, if at all, to the relative motion between blade tip and shroud. Both heat transfer and film effectiveness are measured locally over the test surface using a transient thermal liquid crystal test technique with a computer vision data acquisition and reduction system for various combinations of clearance heights, clearance flow Reynolds numbers, and film flow rates with different coolant injection configurations. The present results reveal a strong dependency of film cooling performance on the choice of the coolant supply hole shapes and injection locations for a given tip geometry.

Sign in / Sign up

Export Citation Format

Share Document