Effects of Inlet Preswirl and Cell Diameter and Depth on Honeycomb Seal Characteristics

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Xin Yan ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Temperature Increase ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Navier Stokes ◽  
Cell Diameter ◽  
Total Temperature ◽  
Honeycomb Seals ◽  
Honeycomb Cell

Three-dimensional Reynolds-averaged Navier–Stokes solutions are employed to investigate the discharge and total temperature increase characteristics of the stepped labyrinth seal with honeycomb land. First, the relations between the windage heating number and the circumferential Mach number at different Reynolds numbers for different honeycomb seals are calculated and compared with the experimental data. The obtained numerical results show that the present three-dimensional periodic model can properly predict the total temperature increase in honeycomb seals. Then, a range of pressure ratios, three inlet preswirl ratios, four sizes of honeycomb cell diameter, and nine sizes of cell depth are selected to investigate the influence of inlet preswirl ratios and honeycomb geometry sizes on the discharge and total temperature increase characteristics of the stepped labyrinth seal. It shows that the leakage rate increases with the increase in cell diameter, and the cell depth has a strong influence on the discharge behavior. However, the influence of the inlet preswirl on the leakage rate is found to be little in the present study. For the total temperature increase characteristic, the inlet preswirl ratio and pressure ratio have more pronounced influence than those of cell depth and diameter. Furthermore, the relations between the leakage rate and cell depth and diameter, as well as the relations between the windage heating power and cell depth and diameter, are not monotonic functions if the pressure ratio is kept constant.

Numerical Investigations for Leakage and Windage Heating in Straight-Through Labyrinth Seals

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Kali Charan Nayak ◽  
Pradip Dutta
Keyword(s):  
Cell Size ◽  
Turbulence Model ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Labyrinth Seal ◽  
Radial Clearance ◽  
Labyrinth Seals ◽  
Turbine Engine ◽  
Honeycomb Cell

The ability to quantify leakage flow and windage heating for labyrinth seals with honeycomb lands is critical in understanding gas turbine engine system performance and predicting its component life. Variety of labyrinth seal configurations (number of teeth, stepped or straight, honeycomb cell size) are in use in gas turbines, and for each configuration, there are many geometric factors that can impact a seal's leakage and windage characteristics. This paper describes the development of a numerical methodology aimed at studying the effect of honeycomb lands on leakage and windage heating. Specifically, a three-dimensional computational fluid dynamics (CFD) model is developed utilizing commercial finite volume-based software incorporating the renormalization group (RNG) k-ε turbulence model with modified Schmidt number. The modified turbulence model is benchmarked and fine-tuned based on several experiments. Using this model, a broad parametric study is conducted by varying honeycomb cell size, pressure ratio (PR), and radial clearance for a four-tooth straight-through labyrinth seal. The results show good agreement with available experimental data. They further indicate that larger honeycomb cells predict higher seal leakage and windage heating at tighter clearances compared to smaller honeycomb cells and smooth lands. However, at open seal clearances larger honeycomb cells have lower leakage compared to smaller honeycomb cells.

Investigations on the Discharge and Total Temperature Increase Characteristics of the Labyrinth Seals With Honeycomb and Smooth Lands

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Xin Yan ◽  
Jun Li ◽  
Liming Song ◽  
Zhenping Feng
Keyword(s):  
Temperature Increase ◽  
Pressure Ratio ◽  
Numerical Approach ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Leakage Flow Rate ◽  
Total Temperature ◽  
Direct Loss ◽  
Sufficient Precision

The viscous work generated by the rotating components of a seal not only represents a direct loss of power but also causes an increase in the total temperature of fluid (windage effect). In order to study the discharge and total temperature increase characteristics of the stepped labyrinth seals with smooth and honeycomb lands, 3D Reynolds-averaged Navier–Stokes solutions from CFX is used in this work. At first, the influences of the inlet preswirl, leakage flow rate, and rotational speed on the total temperature increase in the convergent and divergent stepped labyrinth seals with smooth and honeycomb lands are conducted. The obtained 3D numerical results are well in agreement with the referenced experimental data. It shows that the utilized numerical approach has sufficient precision to predict the total temperature increase in seals. Then, a range of pressure ratios and four sizes of sealing clearance are performed to investigate the effects of sealing clearances and pressure ratio impact on the discharge and total temperature increase of the stepped labyrinth seals with honeycomb and smooth liners.

Numerical Investigations on Leakage Performance of the Rotating Labyrinth Honeycomb Seal

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Jun Li ◽  
Shengru Kong ◽  
Xin Yan ◽  
Shinnosuke Obi ◽  
Zhengping Feng
Keyword(s):  
Flow Rate ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Cell Diameter ◽  
Leakage Flow ◽  
Steam Turbines ◽  
Honeycomb Seal ◽  
Leakage Flow Rate ◽  
Honeycomb Cell

Three-dimensional Reynolds-averaged Navier–Stokes (RANS) solutions from CFX were utilized to investigate the leakage flow characteristics in the labyrinth honeycomb seal of steam turbines. At first, the accuracy and reliability of the utilized RANS approach was demonstrated using the published experimental data of the honeycomb seal. It showed that the utilized numerical method has sufficient precision to predict the leakage performance in seals. Then a range of sealing clearances, cell diameters, cell depths, rotation speeds, and pressure ratios were investigated to determine how these factors affect the leakage flow rate of the labyrinth honeycomb seal. The computed leakage flow rate increased with increasing sealing clearance and pressure ratios. Furthermore, the results show that the studied labyrinth honeycomb seal has the optimum sealing performance in the case of honeycomb cell diameter equals labyrinth step width, and the ratio of the honeycomb cell depth to honeycomb cell diameter is 0.93 under the designed condition. The flow pattern of each case is also illustrated to describe the leakage flow characteristics in labyrinth honeycomb seals.

Automatic Three-Dimensional Optimisation of a Modern Tandem Compressor Vane

2014 ◽  
Author(s):  
R. C. Schlaps ◽  
S. Shahpar ◽  
V. Gümmer
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Trust Region ◽  
Automatic Generation ◽  
Navier Stokes ◽  
Design Parameters ◽  
High Fidelity ◽  
Stall Margin ◽  
Design Choice ◽  
Multipoint Approximation

In order to increase the performance of a modern gas turbine, compressors are required to provide higher pressure ratio and avoid incurring higher losses. The tandem aerofoil has the potential to achieve a higher blade loading in combination with lower losses compared to single vanes. The main reason for this is due to the fact that a new boundary layer is generated on the second blade surface and the turning can be achieved with smaller separation occurring. The lift split between the two vanes with respect to the overall turning is an important design choice. In this paper an automated three-dimensional optimisation of a highly loaded compressor stator is presented. For optimisation a novel methodology based on the Multipoint Approximation Method (MAM) is used. MAM makes use of an automatic design of experiments, response surface modelling and a trust region to represent the design space. The CFD solutions are obtained with the high-fidelity 3D Navier-Stokes solver HYDRA. In order to increase the stage performance the 3D shape of the tandem vane is modified changing both the front and rear aerofoils. Moreover the relative location of the two aerofoils is controlled modifying the axial and tangential relative positions. It is shown that the novel optimisation methodology is able to cope with a large number of design parameters and produce designs which performs better than its single vane counterpart in terms of efficiency and numerical stall margin. One of the key challenges in producing an automatic optimisation process has been the automatic generation of high-fidelity computational meshes. The multi block-structured, high-fidelity meshing tool PADRAM is enhanced to cope with the tandem blade topologies. The wakes of each aerofoil is properly resolved and the interaction and the mixing of the front aerofoil wake and the second tandem vane are adequately resolved.

Unsteady Three-Dimensional Analysis of Inlet Distortion in a Transonic Fan

2006 ◽  
Author(s):  
Peng Sun ◽  
Guotal Feng
Keyword(s):  
Shock Wave ◽  
Total Pressure ◽  
Large Scale ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Inlet Distortion ◽  
Flow Loss ◽  
Large Scale Vortex ◽  
Total Temperature ◽  
Transonic Fan

A time-accurate three-dimensional Navier-Stokes solver of the unsteady flow field in a transonic fan was carried out using "Fluent-parallel" in a parallel supercomputer. The numerical simulation focused on a transonic fan with inlet square wave total pressure distortion and the analysis of result consisted of three aspects. The first was about inlet parameters redistribution and outlet total temperature distortion induced by inlet total pressure distortion. The pattern and causation of flow loss caused by pressure distortion in rotor were analyzed secondly. It was found that the influence of distortion was different at different radial positions. In hub area, transportation-loss and mixing-loss were the main loss patterns. Distortion not only complicated them but enhanced them. Especially in stator, inlet total pressure distortion induced large-scale vortex, which produced backflow and increased the loss. While in casing area, distortion changed the format of shock wave and increased the shock loss. Finally, the format of shock wave and the hysteresis of rotor to distortion were analyzed in detail.

1995 ASME Gas Turbine Award Paper: Development and Application of a Multistage Navier–Stokes Solver: Part I—Multistage Modeling Using Bodyforces and Deterministic Stresses

1998 ◽  
Vol 120 (2) ◽  
pp. 205-214 ◽  
Author(s):  
C. M. Rhie ◽  
A. J. Gleixner ◽  
D. A. Spear ◽  
C. J. Fischberg ◽  
R. M. Zacharias
Keyword(s):  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Design Procedure ◽  
Potential Interaction ◽  
Theoretical Development ◽  
Navier Stokes ◽  
Radial Profiles ◽  
Compressor Performance ◽  
High Level

A multistage compressor performance analysis method based on the three-dimensional Reynolds-averaged Navier-Stokes equations is presented in this paper. This method is an average passage approach where deterministic stresses are used to ensure continuous physical properties across interface planes. The average unsteady effects due to neighboring blades and/or vanes are approximated using deterministic stresses along with the application of bodyforces. Bodyforces are used to account for the “potential” interaction between closely coupled (staged) rows. Deterministic stresses account for the “average” wake blockage and mixing effects both axially and radially. The attempt here is to implement an approximate technique for incorporating periodic unsteady flow physics that provides for a robust multistage design procedure incorporating reasonable computational efficiency. The present paper gives the theoretical development of the stress/bodyforce models incorporated in the code, and demonstrates the usefulness of these models in practical compressor applications. Compressor performance prediction capability is then established through a rigorous code/model validation effort using the power of networked workstations. The numerical results are compared with experimental data in terms of one-dimensional performance parameters such as total pressure ratio and circumferentially averaged radial profiles deemed critical to compressor design. This methodology allows the designer to design from hub to tip with a high level of confidence in the procedure.

Unsteady Interaction of Labyrinth Seal Leakage Flow and Downstream Stator Flow in a Shrouded 1.5 Stage Axial Turbine

2005 ◽  
Author(s):  
P. Peters ◽  
J. R. Menter ◽  
H. Pfost ◽  
A. Giboni ◽  
K. Wolter
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Numerical Data ◽  
Labyrinth Seal ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Experimental Program ◽  
Leakage Flow ◽  
Axial Turbine ◽  
Flow Phenomena

This paper presents the results of experimental and numerical investigations into the flow in a 1.5-stage low-speed axial turbine with shrouded rotor blades and a straight through labyrinth seal. The paper focuses on the time dependent influence of the leakage flow on the downstream stator flow field. The experimental program consists of time accurate measurements of the three-dimensional properties of the flow through ten different measurement planes in the stator passage. The measurements were carried out using pneumatic five-hole probes and three dimensional hot-wire probes at the design operating point of the turbine. The measurement planes extend from the shroud to the casing. The complex three-dimensional flow field is mapped in great detail by 4,800 measurement points and 20 time steps per blade passing period. The time-accurate experimental data of the ten measurement planes was compared with the results of unsteady, numerical simulations of the turbine flow. The 3D-Navier-Stokes Solver CFX-TASCflow was used. The experimental and numerical results correspond well and allow detailed analysis of the flow phenomena. Additionally numerical data behind the rotor is used to connect the entry of the leakage flow with the flow phenomena in the downstream stator passage and behind it. The leakage flow causes strong fluctuations of the flow in the downstream stator. Above all, the high number of measurement points reveals both the secondary flow phenomena and the vortex structures within the blade passage. The time-dependence of both the position and the intensity of the vortices influenced by the leakage flow is shown. The paper shows that even at realistic clearance heights the leakage flow influences considerable parts of the downstream stator and gives rise to negative incidence and flow separation. Thus, labyrinth seal leakage flow should be taken properly into account in the design or optimization process of turbines.

Investigations of Energy Separation Effect in Vortex Tube for Natural Gases

2013 ◽  
Vol 397-400 ◽  
pp. 205-208
Author(s):  
Wen Chuan Wang ◽  
Xiang Jun Fang ◽  
Shi Long Liu ◽  
Wen Long Sun
Keyword(s):  
Mass Fraction ◽  
Vortex Tube ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Energy Separation ◽  
Separation Effect ◽  
Natural Gases ◽  
Temperature Separation ◽  
Total Temperature ◽  
Cold Mass

This paper aims to investigate fixed composition natural gases including N2, CH4 and C2H4 energy separation effect in vortex tube. Energy separation phenomena of those gases were investigated by means of three-dimensional Computational Fluid Dynamics (CFD) method. Flow fields of natural gases in fixed inlet boundary conditions were simulated. The results main factors were found that affect the energy separation with cold mass fraction being 0.7 and pressure drop ratio being 3.90. At the same time, this paper has illustrated the effects and tendencies of energy separation with gases in the tube under the same cold mass flow fraction and cold pressure ratio. The results show mixture gases total temperature difference effect is unchanged varied with the cold mass fraction; CH4% has no effect on the vortex cold end temperature separation, but varied of CH4% has an influence in total temperature and hot end separation effect; total temperature separation effect of CH4% was divided into two sections, one is0%-80%, and the other 80%-100%.

Design and Experimental Study on the Surge Performance Improvement by the Effects of Bleed Slot Casing of a Centrifugal Compressor

2014 ◽  
Author(s):  
Hong Won Kim ◽  
Jae Hoon Chung ◽  
Hyo Seong Lee ◽  
Min Ouk Choi
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Design Parameters ◽  
Navier Stokes Equations ◽  
Operating Range ◽  
Surge Margin ◽  
Commercial Code

The primary design goal of a compressor is focused on improving efficiency. Secondary objective is to widen the compressor’s operating range. This paper presents a numerical and experimental investigation of the influence of the bleed slot to enlarge operating range for the 1.2MW class centrifugal compressor installed in a turbocharger. The main design parameters of the bleed slot casing are upstream slot position, inlet pipe slope, downstream slot position and width. The DOE (design of experiment) method was carried out to optimize the casing design. Numerical analyses were done by the commercial code ANSYS-CFX based on the three dimensional Reynolds-averaged Navier-Stokes equations. From the analysis, as the downstream slot position and width are smaller and upstream position is located away from impeller inlet, efficiency and pressure ratio are increased. Experimental works were done with and without the bleed slot casing. The simulation results were in good agreement with the test data. In case without the bleed slot casing, the surge margin value came out to be only 11.8% but with the optimized bleed slot design, the surge margin reached 23%. Therefore, the surge margin increase of 11.2% was achieved.

Experimental and Numerical Investigation Into the Unsteady Interaction of Labyrinth Seal Leakage Flow and Main Flow in a 1.5-Stage Axial Turbine

2004 ◽  
Author(s):  
A. Giboni ◽  
K. Wolter ◽  
J. R. Menter ◽  
H. Pfost
Keyword(s):  
Secondary Flow ◽  
Three Dimensional ◽  
Labyrinth Seal ◽  
Main Flow ◽  
Navier Stokes ◽  
Experimental Program ◽  
Leakage Flow ◽  
Axial Turbine ◽  
Flow Phenomena ◽  
Grid Points

This paper presents the results of experimental and numerical investigations into the flow in a 1.5-stage low-speed axial turbine with a straight labyrinth seal on the rotor shroud. The paper focuses on the time dependent interaction between the leakage flow and the main flow. The experimental program consists of time accurate measurements of the three-dimensional properties of the main flow. The region of the entering leakage flow downstream of the rotor trailing edge was of special interest. The measurements were carried out using pneumatic five-hole probes and three dimensional hot-wire probes at the design operating point of the turbine. The measurement planes behind the three blade rows extend over one pitch from the shroud to the casing. The complex three-dimensional flow field is mapped in great detail by 1,008 points per measurement plane. The time-accurate experimental data of the three measurement planes was compared with the results of unsteady, numerical simulations of the turbine flow. The 3D-Navier-Stokes Solver CFX-TASCflow was used. The experimental and numerical results correspond well and allow detailed analysis of the mixing process. As demonstrated in this paper, the leakage flow causes strong fluctuations of the secondary flow behind the rotor and the second stator. Above all, the high number of numerical grid points reveals both the secondary flow phenomena and the vortex structures of the mixing zone. The time-dependence of both position and intensity of the vortices is shown. The development of the important leakage vortex is illustrated and explained. The paper shows that even at realistic clearance heights the leakage flow gives rise to negative incidence of considerable parts of the downstream stator which causes the flow to separate. Thus, labyrinth seal leakage flow should be taken properly into account in the design or optimization process of turbomachinery.

Sign in / Sign up

Export Citation Format

Share Document