2D Numerical Simulations of Blade-Vortex Interaction in a Darrieus Turbine

2009 ◽  
Vol 131 (11) ◽  
Author(s):  
E. Amet ◽  
T. Maître ◽  
C. Pellone ◽  
J.-L. Achard
Keyword(s):  
Numerical Analysis ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Water Channel ◽  
Dynamic Stall ◽  
Speed Ratio ◽  
Secondary Effects ◽  
Time Step ◽  
Tip Speed Ratio ◽  
Lift And Drag

The aim of this work is to provide a detailed two-dimensional numerical analysis of the physical phenomena occurring during dynamic stall of a Darrieus wind turbine. The flow is particularly complex because as the turbine rotates, the incidence angle and the blade Reynolds number vary, causing unsteady effects in the flow field. At low tip speed ratio, a deep dynamic stall occurs on blades, leading to large hysteresis lift and drag loops (primary effects). On the other hand, high tip speed ratio corresponds to attached boundary layers on blades (secondary effects). The optimal efficiency occurs in the middle range of the tip speed ratio where primary and secondary effects cohabit. To prove the capacity of the modeling to handle the physics in the whole range of operating condition, it is chosen to consider two tip speed ratios (λ=2 and λ=7), the first in the primary effect region and the second in the secondary effect region. The numerical analysis is performed with an explicit, compressible RANS k-ω code TURBFLOW, in a multiblock structured mesh configuration. The time step and grid refinement sensitivities are examined. Results are compared qualitatively with the visualization of the vortex shedding of Brochier (1986, “Water channel experiments of dynamic stall on Darrieus wind turbine blades,” J. Propul. Power, 2(5), pp. 445–449). Hysteresis lift and drag curves are compared with the data of Laneville and Vitecoq (1986, “Dynamic stall: the case of the vertical axis wind turbine,” Prog. Aerosp. Sci., 32, pp. 523–573).

Water channel experiments of dynamic stall on Darrieus wind turbine blades

1986 ◽  
Vol 2 (5) ◽  
pp. 445-449 ◽  
Author(s):  
G. Brochier ◽  
P. Fraunie ◽  
C. Beguier ◽  
I. Paraschivoiu
Keyword(s):  
Wind Turbine ◽  
Turbine Blades ◽  
Water Channel ◽  
Dynamic Stall ◽  
Wind Turbine Blades

scholarly journals Dynamic stall in vertical axis wind turbines: scaling and topological considerations

2018 ◽  
Vol 841 ◽  
pp. 746-766 ◽  
Author(s):  
Abel-John Buchner ◽  
Julio Soria ◽  
Damon Honnery ◽  
Alexander J. Smits
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vortex Shedding ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Wind Turbine Blades ◽  
Vertical Axis Wind Turbines

Vertical axis wind turbine blades are subject to rapid, cyclical variations in angle of attack and relative airspeed which can induce dynamic stall. This phenomenon poses an obstacle to the greater implementation of vertical axis wind turbines because dynamic stall can reduce turbine efficiency and induce structural vibrations and noise. This study seeks to provide a more comprehensive description of dynamic stall in vertical axis wind turbines, with an emphasis on understanding its parametric dependence and scaling behaviour. This problem is of practical relevance to vertical axis wind turbine design but the inherent coupling of the pitching and velocity scales in the blade kinematics makes this problem of more broad fundamental interest as well. Experiments are performed using particle image velocimetry in the vicinity of the blades of a straight-bladed gyromill-type vertical axis wind turbine at blade Reynolds numbers of between 50 000 and 140 000, tip speed ratios between $\unicode[STIX]{x1D706}=1$ to $\unicode[STIX]{x1D706}=5$, and dimensionless pitch rates of $0.10\leqslant K_{c}\leqslant 0.20$. The effect of these factors on the evolution, strength and timing of vortex shedding from the turbine blades is determined. It is found that tip speed ratio alone is insufficient to describe the circulation production and vortex shedding behaviour from vertical axis wind turbine blades, and a scaling incorporating the dimensionless pitch rate is proposed.

scholarly journals Dynamic Stall of a Vertical-Axis Wind Turbine and Its Control Using Plasma Actuation

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3738 ◽  
Author(s):  
Lu Ma ◽  
Xiaodong Wang ◽  
Jian Zhu ◽  
Shun Kang
Keyword(s):  
Wind Turbine ◽  
Tangential Force ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Dbd Plasma ◽  
Tip Speed Ratio ◽  
Plasma Actuation

In this paper, a dynamic stall control scheme for vertical-axis wind turbine (VAWT) based on pulsed dielectric-barrier-discharge (DBD) plasma actuation is proposed using computational fluid dynamics (CFD). The trend of the wind turbine power coefficient with the tip speed ratio is verified, and the numerical simulation can describe the typical dynamic stall process of the H-type VAWT. The tangential force coefficient and vorticity contours of the blade are compared, and the regular pattern of the VAWT dynamic stall under different tip speed ratios is obtained. Based on the understanding the dynamic stall phenomenon in flow field, the effect of the azimuth of the plasma actuation on the VAWT power is studied. The results show that the azimuth interval of the dynamic stall is approximately 60° or 80° by the different tip speed ratio. The pulsed plasma actuation can suppress dynamic stall. The actuation is optimally applied for the azimuthal position of 60° to 120°.

scholarly journals The effect of Rotor Separation on the Performance of a Dual Rotor Wind Turbine

2021 ◽  
Author(s):  
ANTHONY ADEYANJU ◽  
Omar Mohammed ◽  
Krishpersad Manohar
Keyword(s):  
Wind Turbine ◽  
Turbine Blades ◽  
High Energy ◽  
Separation Distance ◽  
Energy Output ◽  
Power Coefficient ◽  
Total Power ◽  
Speed Ratio ◽  
Horizontal Axis Wind Turbine ◽  
Tip Speed Ratio

This study conducted simulation and experimental analysis on a dual rotor horizontal axis wind turbine to determine the effect of rotor separation on its performance. An air study was conducted to optimize the turbine blades to a local climate of Trinidad, it was determined that a NACA 64-315 air foil would be the most optimum for the conditions. QBlade software was used for the simulation, the power flow performance for multiple iterations of wind speed was found for the design. The effect of rotor separation on the performance of the dual rotor wind turbine was studied with rotor separation 0.25 m to 3.0 m at an interval of 0.25 m and it was discovered that the smallest rotor separation 0.25 m shows the largest tip speed ratio, while the largest rotor separation distance 3m has the smallest tip speed ratio at a fan speed of 1m/s. Also, as the rotor separation decreases the power coefficient (C P ) and the total power increase, which resulted to high energy output of the DRHAWT. This result is valid for the QBlade simulations and the experimental results.

scholarly journals Performance Analysis and Optimization of a Vertical-Axis Wind Turbine with a High Tip-Speed Ratio

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 996
Author(s):  
Liang Li ◽  
Inderjit Chopra ◽  
Weidong Zhu ◽  
Meilin Yu
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Loads ◽  
Tip Speed Ratio ◽  
Aerodynamic Model ◽  
Lift And Drag

In this work, the aerodynamic performance and optimization of a vertical-axis wind turbine with a high tip-speed ratio are theoretically studied on the basis of the two-dimensional airfoil theory. By dividing the rotating plane of the airfoil into the upwind and downwind areas, the relationship among the angle of attack, azimuth, pitch angle, and tip-speed ratio is derived using the quasi-steady aerodynamic model, and aerodynamic loads on the airfoil are then obtained. By applying the polynomial approximation to functions of lift and drag coefficients with the angle of attack for symmetric and asymmetric airfoils, respectively, explicit expressions of aerodynamic loads as functions of the angle of attack are obtained. The performance of a fixed-pitch blade is studied by employing a NACA0012 model, and influences of the tip speed ratio, pitch angle, chord length, rotor radius, incoming wind speed and rotational speed on the performance of the blade are discussed. Furthermore, the optimization problem based on the dynamic-pitch method is investigated by considering the maximum value problem of the instantaneous torque as a function of the pitch angle. Dynamic-pitch laws for symmetric and asymmetric airfoils are derived.

scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

scholarly journals Design and Analysis of a Wind Turbine Blade with Dimples to Enhance the Efficiency through CFD with ANSYS R16.0

2018 ◽  
Vol 207 ◽  
pp. 02004
Author(s):  
M. Rajaram Narayanan ◽  
S. Nallusamy ◽  
M. Ragesh Sathiyan
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Turbine Blades ◽  
Electrical Energy ◽  
Optimum Combination ◽  
Surface Topology ◽  
Wind Turbine Blades ◽  
Lift And Drag

In the global scenario, wind turbines and their aerodynamics are always subjected to constant research for increasing their efficiency which converts the abundant wind energy into usable electrical energy. In this research, an attempt is made to increase the efficiency through the changes in surface topology of wind turbines through computational fluid dynamics. Dimples on the other hand are very efficient in reducing air drag as is it evident from the reduction of drag and increase in lift in golf balls. The predominant factors influencing the efficiency of the wind turbines are lift and drag which are to be maximized and minimized respectively. In this research, surface of turbine blades are integrated with dimples of various sizes and arrangements and are analyzed using computational fluid dynamics to obtain an optimum combination. The analysis result shows that there is an increase in power with about 15% increase in efficiency. Hence, integration of dimples on the surface of wind turbine blades has helped in increasing the overall efficiency of the wind turbine.

scholarly journals Effects of tip speed ratio on the performance of an H-Darriues wind turbine with NACA 4415 air foil

2020 ◽  
Author(s):  
Yogie P. Sibagariang ◽  
Indro Pramono ◽  
Koki Kishinami ◽  
Himsar Ambarita
Keyword(s):  
Wind Turbine ◽  
Speed Ratio ◽  
Tip Speed Ratio
Sign in / Sign up

Export Citation Format

Share Document