Discussion: “Measurement of Oil-Film Thickness Between Disks by Electrical Conductivity” (El-Sisi, S. I., and Shawki, G. S. A., 1960, ASME J. Basic Eng., 82, pp. 12–16)

1960 ◽  
Vol 82 (1) ◽  
pp. 17-17
Author(s):  
Ragnar Holm
Keyword(s):  
Electrical Conductivity ◽  
Film Thickness ◽  
Oil Film

Measurement of Oil-Film Thickness Between Disks by Electrical Conductivity

1960 ◽  
Vol 82 (1) ◽  
pp. 12-16 ◽  
Author(s):  
S. I. El-Sisi ◽  
G. S. A. Shawki
Keyword(s):  
Electrical Conductivity ◽  
Film Thickness ◽  
Testing Machine ◽  
Rotating Disk ◽  
Substantial Improvement ◽  
Film Resistance ◽  
Test Results ◽  
Oil Film ◽  
Gear Teeth ◽  
Special Apparatus

A special apparatus is designed to measure the oil-film thickness between two stationary disks (simulating meshing gear teeth) by applying a-c or d-c potential across the film and measuring its resistance for given gap between the disks. Experiments show that the treatment of oil with additive (sodium-petroleum sulphonate in this case) may well lead to a considerable increase in its electrical conductivity, and to a substantial improvement in the independence of the oil-film resistance of the electrical history and temperature of the oil. A reliable relationship could eventually be obtained between the oil-film resistance and relevant thickness. Test results are employed in investigating the behavior of the oil film in a rotating-disk testing machine developed by the authors for studying the performance of meshing gear teeth with adequate supply of lubricant.

The Surface-Roughness of Bearing-Surfaces and its Relation to Oil Film Thickness at Breakdown

1949 ◽  
Vol 161 (1) ◽  
pp. 73-79 ◽  
Author(s):  
A. Cameron
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Hydrodynamic Theory ◽  
Quantitative Relation ◽  
Metal Contact ◽  
Initial Contact ◽  
Frictional Drag ◽  
Average Roughness ◽  
Finished Steel ◽  
Oil Film

In this paper the relation of surface roughness of bearing surfaces to allowable film thickness is studied quantitatively with a simple Michell pad apparatus. The pads used were faced with white metal and ran against mild steel collars. The lubricants studied were water, soap solution, paraffin, and light oil. There was little difference in the frictional behaviour of any of the lubricants, except that the aqueous lubricants would not run with very finely finished steel surfaces. The onset of metal to metal contact was detected by an increase in the frictional drag, and also by the change in electrical conductivity between the pad and collar—an extremely sensitive method. The paper shows that there is, at any rate for this system, a quantitative relation between the total surface roughness of the rubbing surfaces and the calculated oil film thickness both at the initial metal to metal contact and seizure. Initial contact occurs when the outlet film thickness, calculated from normal hydrodynamic theory, falls to three times the maximum surface roughness and seizure occurs when it is double the average roughness.

Influence of Surface Waviness on the Thermal Elastohydrodynamic Lubrication of an Eccentric-Tappet Pair

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
J. Wang ◽  
C. H. Venner ◽  
A. A. Lubrecht
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Surface Waviness ◽  
Film Pressure ◽  
Oil Film ◽  
Working Cycle ◽  
Temperature Oscillations ◽  
Minimum Film Thickness ◽  
Traction Coefficient ◽  
Oil Film Pressure

The effect of single-sided and double-sided harmonic surface waviness on the film thickness, pressure, and temperature oscillations in an elastohydrodynamically lubricated eccentric-tappet pair has been investigated in relation to the eccentricity and the waviness wavelength. The results show that, during one working cycle, the waviness causes significant fluctuations of the oil film, pressure, and temperature, as well as a reduction in minimum film thickness. Smaller wavelength causes more dramatic variations in oil film. The fluctuations of the pressure, film thickness, temperature, and traction coefficient caused by double-sided waviness are nearly the same compared with the single-sided waviness, but the variations are less intense.

Sign in / Sign up

Export Citation Format

Share Document