The Effect of Pressure on the Non-Newtonian Behavior of Polymer Blended Petroleum Oils

1969 ◽  
Vol 91 (3) ◽  
pp. 459-462 ◽  
Author(s):  
J. D. Novak ◽  
W. O. Winer
Keyword(s):  
Shear Stress ◽  
Shear Strain ◽  
Atmospheric Pressure ◽  
Weight Percent ◽  
Elevated Pressure ◽  
Base Oil ◽  
Effect Of Pressure ◽  
Elevated Pressures ◽  
Capillary Type ◽  
Newtonian Behavior

The shear dependence of polymer containing oils at elevated pressure was observed in a capillary-type viscometer and is reported. Recoverable shear strain was not observed at elevated pressures but was observed at atmospheric pressure in the blends at the same shear stress. The fluids examined included a paraffinic base oil (B), B plus four and eight weight percent methacrylate, B plus four weight percent styrene, a naphthenic base oil (F), and F plus four weight percent methacrylate.

Effect of pressure on hydraulic conductivity of endothelial monolayers: role of endothelial cleft shear stress

1999 ◽  
Vol 87 (1) ◽  
pp. 261-268 ◽  
Author(s):  
John M. Tarbell ◽  
Lucas Demaio ◽  
Mark M. Zaw
Keyword(s):  
Nitric Oxide ◽  
Shear Stress ◽  
Hydraulic Conductivity ◽  
Elevated Pressure ◽  
Transmural Pressure ◽  
Luminal Surface ◽  
Aortic Endothelial Cells ◽  
Effect Of Pressure ◽  
Steady State Levels ◽  
Transmural Flow

Significant changes in transvascular pressure occur in pulmonary hypertension, microgravity, and many other physiological and pathophysiological circumstances. Using bovine aortic endothelial cells grown on porous, rigid supports, we demonstrate that step changes in transmural pressure of 10, 20, and 30 cmH2O induce significant elevations in endothelial hydraulic conductivity ( L p) that require 5 h to reach new steady-state levels. The increases in L p can be reversed by addition of a stable cAMP analog (dibutyryl cAMP), and the increases in L pin response to pressure can be inhibited significantly with nitric oxide synthase inhibitors ( N G-monomethyl-l-arginine and nitro-l-arginine methyl ester). The increase in L p was not due to pressure-induced stretch because the endothelial cell (EC) support was rigid. It is unlikely that the increase in L p was due to a direct effect of pressure because exposure of the cells to elevated pressure (25 cmH2O) for 4 h had no effect on the volume flux driven by a transmural pressure of 10 cmH2O. We hypothesize that elevated endothelial cleft shear stress induced by elevated transmural flow in response to elevated pressure stimulates the increase in L p through a nitric oxide-cAMP-dependent mechanism. This is consistent with recent studies of the effects of shear stress on the luminal surface of ECs. We provide simple estimates of endothelial cleft shear stress, which suggest magnitudes comparable to those imposed by blood flow on the luminal surface of ECs.

scholarly journals A Monotonic Smeared Truss Model to Predict the Envelope Shear Stress—Shear Strain Curve for Reinforced Concrete Panel Elements under Cyclic Shear

2021 ◽  
Vol 2 (1) ◽  
pp. 174-194
Author(s):  
Luís Bernardo ◽  
Saffana Sadieh
Keyword(s):  
Shear Stress ◽  
Reinforced Concrete ◽  
Shear Strain ◽  
Peak Load ◽  
Strain Curve ◽  
Fiber Reinforced Polymers ◽  
Shear Stresses ◽  
Cyclic Shear ◽  
Concrete Panels ◽  
Truss Model

In previous studies, a smeared truss model based on a refinement of the rotating-angle softened truss model (RA-STM) was proposed to predict the full response of structural concrete panel elements under in-plane monotonic loading. This model, called the “efficient RA-STM procedure”, was validated against the experimental results of reinforced and prestressed concrete panels, steel fiber concrete panels, and reinforced concrete panels externally strengthened with fiber-reinforced polymers. The model incorporates equilibrium and compatibility equations, as well as appropriate smeared constitutive laws of the materials. Besides, it incorporates an efficient algorithm for the calculation procedure to compute the solution points without using the classical trial-and-error technique, providing high numerical efficiency and stability. In this study, the efficient RA-STM procedure is adapted and checked against some experimental data related to reinforced concrete (RC) panels tested under in-plane cyclic shear until failure and found in the literature. Being a monotonic model, the predictions from the model are compared with the experimental envelopes of the hysteretic shear stress–shear strain loops. It is shown that the predictions for the shape (at least until the peak load is reached) and for key shear stresses (namely, cracking, yielding, and maximum shear stresses) of the envelope shear stress–shear strain curves are in reasonably good agreement with the experimental ones. From the obtained results, the efficient RA-STM procedure can be considered as a reliable model to predict some important features of the response of RC panels under cyclic shear, at least for a precheck analysis or predesign.

Study on Thermal Cycling of Sn0.7Cu Solder

2013 ◽  
Vol 791-793 ◽  
pp. 362-365
Author(s):  
Li Yang ◽  
Ju Li Li ◽  
Jing Guo Ge ◽  
Meng Li ◽  
Nan Ji
Keyword(s):  
Shear Stress ◽  
Steady State ◽  
High Temperature ◽  
Thermal Cycling ◽  
Shear Strain ◽  
Maximum Shear Stress ◽  
Steady State Creep ◽  
Maximum Shear Strain ◽  
Cycle Number ◽  
State Cycle

Thermal cycling of a unit Sn0.7Cu solder was studied based on the steady-state creep constitutive equation and Matlab software. The results show that there is a steady-state cycle for the thermal cycling of unit Sn0.7Cu eutectic solder. In steady-state thermal cycling, the shear stress is increased with the increase of temperature. There is a stage of stress relaxation during high temperature. A liner relationship between maximum shear stress and maximum shear strain is observed during thermal cycling. The metastable cycle number is declined greatly with the increase of maximum shear strain.

scholarly journals The influence of base oil type on the rheological properties of ecological lubricating greases

Nafta-Gaz ◽  
2021 ◽  
Vol 77 (2) ◽  
pp. 127-135
Author(s):  
Rafał Kozdrach ◽  
Keyword(s):  
Shear Stress ◽  
Shear Rate ◽  
Rheological Properties ◽  
Measurement Data ◽  
Measuring System ◽  
Rheological Parameters ◽  
Flow Curves ◽  
Lubricating Grease ◽  
Dispersion Phase ◽  
Base Oil

The article presents the results of research on the influence the type of base oil in lubricating compositions has on the rheological parameters of selected lubricants. Vegetable, mineral, and synthetic dispersion phases were used to produce lubricating greases. The modified amorphous silica was used as the dispersed phase. However, as a modifying additive was used a substance containing the antioxidants, corrosion inhibitors, and EP/AW additives. The experiments on rheological properties were carried out using a Physica MCR 101 rotational rheometer (manufactured by Anton Paar), equipped with a diffusion air bearing and connected to a pneumatic supply – an oil-free Jun-Air compressor and air drying block. The device is equipped with a Peltier system for temperature control in the range of –20°C to 200°C and an external thermostatic VISCOTHERM V2 system, working in the temperature range of –20°C to 200°C. The rheometer control and measurement data analysis were performed using Rheoplus software. The tests were carried out using a cone-plate measuring system with a shear rate range of 0.01–100 s-1 at 20°C for lubricating compositions prepared on various oil bases. To evaluate the value of rheological parameters, the results of tests of the dependence between shear stress and shear rate (flow curves) were used. For the theoretical determined on the flow curves, the following rheological models were used: Bingham, Herschel–Bulkley, Casson, and Tscheuschner. The values of the shear stress (yield point) in depending on the type of dispersion phase has changed. This proves that the use of a base oil with the appropriate functional properties does not weaken, but reinforces the spatial structure of a lubricating grease. It has an important meaning when selecting construction parameters when designing a central lubrication system with grease made from a vegetable oil base (Abyssinian oil). The rheological properties of the lubricating grease are influenced by the type of base oil and thickener, any additives in the grease, the production technology of the grease, and the conditions in which it is used. The tests revealed an important influence of the base oil on the rheological parameters that describe the behaviour of lubricating compositions subjected to stresses and strains in a lubricating system.

scholarly journals Erebus Glacier Tongue, Mcmurdo Sound, Antarctica

1974 ◽  
Vol 13 (67) ◽  
pp. 27-35 ◽  
Author(s):  
G. Holdsworth
Keyword(s):  
Shear Stress ◽  
Strain Rate ◽  
Shear Strain ◽  
Longitudinal Strain ◽  
Strain Rates ◽  
Shear Strain Rate ◽  
Mcmurdo Sound ◽  
Glacier Tongue ◽  
The Past ◽  
Image Position

Examination of the past and present behaviour of the Erebus Glacier tongue over the last 60 years indicates that a major calving from the tongue appears to be imminent. Calculations of the regime of the tongue indicate that bottom melt rates may exceed 1 m a−1. By successive mapping of the ice tongue between the years 1947 and 1970, longitudinal strain-rates were determined using the change in distance between a set of 15 teeth, which are a prominent marginal feature of the tongue. Assuming a flow law for ice of the form where τ is the effective shear stress and is the effective shear strain-rate, values of the exponent n = 3 and B = 1 × 108 N m−2 are determined. These are in fair agreement with published values.

An Energy Approach to the Mechanics of Discontinuous Chip Formation

1964 ◽  
Vol 86 (2) ◽  
pp. 157-162 ◽  
Author(s):  
W. K. Luk ◽  
R. C. Brewer
Keyword(s):  
Shear Stress ◽  
Shear Strain ◽  
Normal Stress ◽  
Chip Formation ◽  
Strain Energy ◽  
Energy Condition ◽  
Stress And Strain ◽  
Rupture Plane ◽  
Shear Stress And Strain ◽  
Shear Strain Energy

After briefly reviewing previous work in this field, the authors propose that rupture of the chip work contact (to give a discontinuous chip) is governed by a limiting shear strain energy condition. Assuming that shear stress and strain at rupture are dependent on the compressive normal stress, a criterion for the direction of the rupture plane is deduced. Using some results given by Field and Merchant, the authors then compare their calculated direction of rupture with that experimentally observed. Some indication that the agreement is not entirely fortuitous is afforded by checking the calculated shear strain energy at fracture with that calculated from force and chip measurements.

Sign in / Sign up

Export Citation Format

Share Document