scholarly journals Erratum: “The Effect of Viscous Shear Heating on Both Film Thickness and Rolling Traction in an E. H. L. Line Contact—Part I: Fully Flooded Conditions” (Journal of Lubrication Technology, 1978, 100, pp. 346–352)

1978 ◽  
Vol 100 (4) ◽  
pp. 466-466
Author(s):  
P. G. Goksem ◽  
R. A. Hargreaves
Keyword(s):  
Film Thickness ◽  
Line Contact ◽  
Viscous Shear ◽  
Shear Heating ◽  
Contact Part

The Effect of Viscous Shear Heating on Both Film Thickness and Rolling Traction in an EHL Line Contact—Part I: Fully Flooded Conditions

1978 ◽  
Vol 100 (3) ◽  
pp. 346-352 ◽  
Author(s):  
P. G. Goksem ◽  
R. A. Hargreaves
Keyword(s):  
Experimental Data ◽  
Theoretical Analysis ◽  
Film Thickness ◽  
Thermal Effect ◽  
Line Contact ◽  
Heating Effect ◽  
Viscous Shear ◽  
Isothermal Case ◽  
Shear Heating ◽  
Contact Part

A theoretical analysis of both fully flooded rolling traction and film thickness in an EHL line contact is described and modified formulas for fully flooded isothermal conditions are presented. These are compared with the Grubin, Dowson, and Higginson film thickness formulas, and the rolling traction theory by Archard and Baglin (1975). The effect of viscous shear heating in the inlet region has been investigated and new equations for both fully flooded film thickness and rolling traction, including this thermal effect, are introduced. These equations predict significant reductions in both film thickness and rolling traction, relative to the isothermal case, as speed is increased. Viscous shear heating effect is found to be negligible only at very low rolling speeds. The results of the theoretical analysis compare well with experimental data presented by Dyson, Naylor, and Wilson (1966) and Adams and Hirst (1973).

The Effect of Viscous Shear Heating on Both Film Thickness and Rolling Traction in an EHL Line Contact—Part II: Starved Conditions

1978 ◽  
Vol 100 (3) ◽  
pp. 353-358 ◽  
Author(s):  
P. G. Goksem ◽  
R. A. Hargreaves
Keyword(s):  
Theoretical Analysis ◽  
Film Thickness ◽  
Approximate Equation ◽  
Theoretical Work ◽  
Line Contact ◽  
Viscous Shear ◽  
Isothermal Case ◽  
Shear Heating ◽  
Boundary Distance ◽  
Contact Part

A theoretical analysis of both fully flooded rolling traction and film thickness in an EHL line contact has been presented in Part I of this paper. The effect of viscous shear heating was investigated and the results predict a significant reduction in both fully flooded film thickness and rolling traction, relative to the isothermal case, as speed is increased. In this part of the Series, the analysis is extended to consider the calculation of starved rolling traction and film thickness, including viscous shear heating of the lubricant in the inlet region. An approximate equation has been developed, which predicts both the isothermal and non isothermal starved film thickness for all conditions of inlet boundary distance, rolling speed, load, geometry, material constants and lubricant properties. The results show that both rolling traction and film thickness are significantly reduced from the starved isothermal case. For the starved isothermal case, the theoretical analysis for the film thickness agrees closely with experimental data and published empirical formula by Wymer and Cameron, (1974) and the theoretical work of Wolveridge, et al. (1971).

Thermal and Starvation Effects on the Minimum Film Thickness in Inlet Zone in Cold Rolling

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
P. Singh ◽  
R. K. Pandey ◽  
Y. Nath
Keyword(s):  
Film Thickness ◽  
Temperature Rise ◽  
Speed Reduction ◽  
Heating Effects ◽  
Empirical Relations ◽  
Viscous Shear ◽  
Minimum Film Thickness ◽  
Starvation Effects ◽  
Shear Heating ◽  
Inlet Zone

The main objective of this research is to analyze the variation of minimum film thickness in the inlet zone of roll-strip interface by incorporating starvation and viscous shear heating effects at high rolling speeds (5–20m∕s), reduction ratios (0.05–0.20), and slip values (varying up to 20%). An additional objective of this paper is to develop empirical relations for predictions of minimum film thicknesses (both isothermal and thermal) and maximum film temperature rise in the inlet zone of the lubricated roll strip contact as functions of roll-speed, reduction ratio, material parameter, slip, and starvation parameter. An efficient numerical method based on Lobatto quadrature technique is adopted for rigorous analysis of the present problem. The results reveal that the existence of starvation seems to be beneficial in terms of reduction in maximum film temperature rise as well as reduction in quantity of oil required for lubrication provided thin continuous film exists at the contact.

scholarly journals Effect of an Improved Yasutomi Pressure-Viscosity Relationship on the Elastohydrodynamic Line Contact Problem

2013 ◽  
Vol 2013 ◽  
pp. 1-7
Author(s):  
Vincenzo Petrone ◽  
Adolfo Senatore ◽  
Vincenzo D'Agostino
Keyword(s):  
High Pressure ◽  
Film Thickness ◽  
Free Volume ◽  
Experimental Studies ◽  
Line Contact ◽  
Volume Model ◽  
Free Volume Model ◽  
Pressure Area ◽  
New Formulation ◽  
Lubricant Viscosity

This paper presents the application of an improved Yasutomi correlation for lubricant viscosity at high pressure in a Newtonian elastohydrodynamic line contact simulation. According to recent experimental studies using high pressure viscometers, the Yasutomi pressure-viscosity relationship derived from the free-volume model closely represents the real lubricant piezoviscous behavior for the high pressure typically encountered in elastohydrodynamic applications. However, the original Yasutomi correlation suffers from the appearance of a zero in the function describing the pressure dependence of the relative free volume thermal expansivity. In order to overcome this drawback, a new formulation of the Yasutomi relation was recently developed by Bair et al. This new function removes these concerns and provides improved precision without the need for an equation of state. Numerical simulations have been performed using the improved Yasutomi model to predict the lubricant pressure-viscosity, the pressure distribution, and the film thickness behavior in a Newtonian EHL simulation of a squalane-lubricated line contact. This work also shows that this model yields a higher viscosity at the low-pressure area, which results in a larger central film thickness compared with the previous piezoviscous relations.

scholarly journals Optical Analysis of Ball Bearing Starvation

1971 ◽  
Vol 93 (3) ◽  
pp. 349-361 ◽  
Author(s):  
L. D. Wedeven ◽  
D. Evans ◽  
A. Cameron
Keyword(s):  
Film Thickness ◽  
Ball Bearing ◽  
Point Contact ◽  
Experimental Measurements ◽  
Line Contact ◽  
Optical Analysis ◽  
Grease Lubrication ◽  
Theoretical Predictions ◽  
Pressure Stress ◽  
Starvation Conditions

Elastohydrodynamic oil film measurements for rolling point contact under starvation conditions are obtained using optical interferometry. The experimental measurements present a reasonably clear picture of the starvation phenomenon and are shown to agree with theoretical predictions. Starvation inhibits the generation of pressure and, therefore, reduces film thickness. It also causes the overall pressure, stress, and elastic deformation to become more Hertzian. Additional experiments using interferometry illustrate: the cavitation pattern, lubricant entrapment, grease lubrication, ball spin, and edge effects in line contact.

Effect of Rolling Velocity and Maximum Hertzian Pressure on Fluid Film in Steady State EHL Line Contact with Rough Surface and Linear Piezoviscosity

2014 ◽  
Vol 592-594 ◽  
pp. 1371-1375
Author(s):  
Nitesh Talekar ◽  
Punit Kumar
Keyword(s):  
Surface Roughness ◽  
Steady State ◽  
Film Thickness ◽  
Rough Surface ◽  
Computer Code ◽  
Fluid Film ◽  
Line Contact ◽  
Rolling Velocity ◽  
Load Carrying ◽  
Lubricated Contact

Consideration of surface roughness in steady state EHL line contact is the first step towards understanding the lubrication of rough surface problem. Current paper investigates the use of sinusoidal waviness in the contact; more precisely it gives performance of real fluid in EHL line contact. The effect of various parameters like rolling velocity (U) and maximum Hertzian pressure (ph) on surface roughness by using properties of linear and exponential piezo-viscosity is taken into consideration to evaluate behavior of pressure distribution of load carrying fluid film and film thickness. Full isothermal, Newtonian simulation of EHL problem gives described effects. Spiking or fluctuation of pressure and film thickness curves is expected to show presence of irregularities on the surface chosen and amount of fluctuation depends on certain parameters and intensity of irregularities present. Rolling side domain of-4.5 ≤ X ≤ 1.5 with grid size ∆X=0.01375 is selected. A computer code is developed to solve Reynolds equation, which governs the generation of pressure in the lubricated contact zone is discritized and solved along with load balance equation using Newton-Raphson technique.

Some Limitations in Applying Classical EHD Film Thickness Formulas to a High-Speed Bearing

1981 ◽  
Vol 103 (2) ◽  
pp. 295-301 ◽  
Author(s):  
J. J. Coy ◽  
E. V. Zaretsky
Keyword(s):  
Film Thickness ◽  
High Speed ◽  
Heating Effects ◽  
Theoretical Predictions ◽  
Traction Fluid ◽  
Shear Heating ◽  
Thickness Measurements ◽  
Inner Race ◽  
Maximum Stresses ◽  
Good Agreement

Elastohydrodynamic film thickness was measured for a 20-mm ball bearing using the capacitance technique. The bearing was thrust loaded to 90, 448, and 778 N (20, 100, and 175 lb). The corresponding maximum stresses on the inner race were 1.28, 2.09, and 2.45 GPa (185,000, 303,000, and 356,000 psi). Test speeds ranged from 400 to 14,000 rpm. Film thickness measurements were taken with four different lubricants: (a) synthetic paraffinic, (b) synthetic paraffinic with additives, (c) neopentylpolyol (tetra) ester meeting MIL-L-23699A specifications, and (d) synthetic cycloaliphatic hydrocarbon traction fluid. The test bearing was mist lubricated. Test temperatures were 300, 338, and 393 K. The measured results were compared to theoretical predictions using the formulae of Grubin, Archard and Cowking, Dowson and Higginson, and Hamrock and Dowson. There was good agreement with theory at low dimensionless speed, but the film was much smaller than theory predicts at higher speeds. This was due to kinematic starvation and inlet shear heating effects. Comparisons with Chiu’s theory on starvation and Cheng’s theory on inlet shear heating were made.

scholarly journals Fast Approach for Calculating Film Thicknesses and Pressures in Elastohydrodynamically Lubricated Contacts at High Loads

1986 ◽  
Vol 108 (3) ◽  
pp. 411-419 ◽  
Author(s):  
L. G. Houpert ◽  
B. J. Hamrock
Keyword(s):  
High Pressure ◽  
Film Thickness ◽  
Line Contact ◽  
Elastic Deformations ◽  
New Approach ◽  
Lubricated Contacts ◽  
Fast Approach ◽  
Pressure Spike

The film thicknesses and pressures in elastohydrodynamically lubricated contacts have been calculated for a line contact by using an improved version of Okamura’s approach. The new approach allows for lubricant compressibility, the use of Roelands viscosity, a general mesh (nonconstant step), and accurate calculations of the elastic deformations. The new approach is described, and the effects on film thickness, pressure, and pressure spike of each of the improvements are discussed. Successful runs have been obtained at high pressure (to 4.8 GPa) with low CPU times.

Experimental study on line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuqin Yang ◽  
Dexing Hu ◽  
Qianhao Xiao ◽  
Shun Zhao
Keyword(s):  
Film Thickness ◽  
Surface Texture ◽  
Inhibitory Effect ◽  
Lubricating Oil ◽  
Line Contact ◽  
Grease Lubrication ◽  
Content Type ◽  
Oil Film ◽  
Crown Width ◽  
Lubrication Properties

Purpose This paper aims to study line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers as well as the effect of different crown widths (dw) on oil film thickness under textured conditions. Design/methodology/approach The laser processing method was used to make the micro-texture on the surface of GCr15 steel rollers; lithium grease was used as the lubricant, and line-contact elastohydrodynamic grease lubrication experiments under pure sliding conditions were performed on light interference elastohydrodynamic-lubricated experimental table. Findings The results show that the line-contact elastohydrodynamic grease lubrication is closely related to the textured crown width of steel rollers. At low speeds and light loads, texturing has an inevitable inhibitory effect on the formation of the lubricating oil film, and the smaller the width of the crown area, the more obvious the inhibitory effect, which is not conducive to the improvement of the lubrication condition. At high speeds and high loads, the textured roller with dw = 1 mm has the largest oil film thickness and shows better lubrication performance. Originality/value At present, there is little research on the surface texture of line-contact friction pairs. This work explores the effect of different textured crown width on the lubricating properties of line-contact elastohydrodynamic grease lubrication by experiment. It provides a new theoretical basis for the subsequent practical application of surface texture technology.

Size effect on thermal elastohydrodynamic lubrication of industrial chain bush-pin hinge pair

2019 ◽  
Vol 71 (9) ◽  
pp. 1080-1085 ◽  
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Yi Liu ◽  
Longjie Dai ◽  
Zhaohua Shang
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Curvature Radius ◽  
Line Contact ◽  
Content Type ◽  
Oil Film ◽  
Industrial Chain ◽  
Infinite Line

Purpose The purpose of this paper is to use elastohydrodynamic lubrication (EHL) theory to study the variation of the equivalent curvature radius “R” on the change of oil film thickness, pressure, temperature rise and friction coefficient in the contact zone between bush-pin in industrial chain drive. Design/methodology/approach In this paper, the contact between bush and pin is simplified as infinitely long line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. The two constitutive equations, namely, Newton fluid and Ree–Eyring fluid are used in the calculations. Findings It is found that with the increase of equivalent curvature radius, the thickness of oil film decreases and the temperature rise increases. Under the same condition, the friction coefficient of Newton fluid is higher than that of Ree–Eyring fluid. When the load increases, the oil film thickness decreases, the temperature rise increases and the friction coefficient decreases; and the film thickness increases with the increase of the entraining speed under the condition “R < 1,000 mm”. Research limitations/implications The infinite line contact assumption is only an approximation. For example, the distances between the two inner plates are 5.72 mm, by considering the two parts assembled into the inner plates, the total length of the bush is less than 6 mm. The diameter of the pin and the bore diameter of the bush are 3.28 and 3.33 mm. However, the infinite line contact is also helpful in understanding the general variation of oil film characteristics and provides a reference for the future study of finite line contact of chain problems. Originality/value The change of the equivalent radius R on the variation of the oil film in the contact of the bush and the pin in industrial chain drive was investigated. The size effect influences the lubrication characteristic greatly in the bush-pin pair.

Sign in / Sign up

Export Citation Format

Share Document