scholarly journals Optical Analysis of Ball Bearing Starvation

1971 ◽  
Vol 93 (3) ◽  
pp. 349-361 ◽  
Author(s):  
L. D. Wedeven ◽  
D. Evans ◽  
A. Cameron
Keyword(s):  
Film Thickness ◽  
Ball Bearing ◽  
Point Contact ◽  
Experimental Measurements ◽  
Line Contact ◽  
Optical Analysis ◽  
Grease Lubrication ◽  
Theoretical Predictions ◽  
Pressure Stress ◽  
Starvation Conditions

Elastohydrodynamic oil film measurements for rolling point contact under starvation conditions are obtained using optical interferometry. The experimental measurements present a reasonably clear picture of the starvation phenomenon and are shown to agree with theoretical predictions. Starvation inhibits the generation of pressure and, therefore, reduces film thickness. It also causes the overall pressure, stress, and elastic deformation to become more Hertzian. Additional experiments using interferometry illustrate: the cavitation pattern, lubricant entrapment, grease lubrication, ball spin, and edge effects in line contact.

Experimental study on line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuqin Yang ◽  
Dexing Hu ◽  
Qianhao Xiao ◽  
Shun Zhao
Keyword(s):  
Film Thickness ◽  
Surface Texture ◽  
Inhibitory Effect ◽  
Lubricating Oil ◽  
Line Contact ◽  
Grease Lubrication ◽  
Content Type ◽  
Oil Film ◽  
Crown Width ◽  
Lubrication Properties

Purpose This paper aims to study line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers as well as the effect of different crown widths (dw) on oil film thickness under textured conditions. Design/methodology/approach The laser processing method was used to make the micro-texture on the surface of GCr15 steel rollers; lithium grease was used as the lubricant, and line-contact elastohydrodynamic grease lubrication experiments under pure sliding conditions were performed on light interference elastohydrodynamic-lubricated experimental table. Findings The results show that the line-contact elastohydrodynamic grease lubrication is closely related to the textured crown width of steel rollers. At low speeds and light loads, texturing has an inevitable inhibitory effect on the formation of the lubricating oil film, and the smaller the width of the crown area, the more obvious the inhibitory effect, which is not conducive to the improvement of the lubrication condition. At high speeds and high loads, the textured roller with dw = 1 mm has the largest oil film thickness and shows better lubrication performance. Originality/value At present, there is little research on the surface texture of line-contact friction pairs. This work explores the effect of different textured crown width on the lubricating properties of line-contact elastohydrodynamic grease lubrication by experiment. It provides a new theoretical basis for the subsequent practical application of surface texture technology.

Lubricating Grease Replenishment in an Elastohydrodynamic Point Contact

1993 ◽  
Vol 115 (3) ◽  
pp. 501-506 ◽  
Author(s):  
Henrik A˚stro¨m ◽  
Jan Ove O¨stensen ◽  
Erik Ho¨glund
Keyword(s):  
Film Thickness ◽  
High Speed ◽  
Video Recording ◽  
Point Contact ◽  
Video Camera ◽  
Lubricating Oil ◽  
Spin Motion ◽  
Lubricating Grease ◽  
Lubricating Film ◽  
Theoretical Predictions

A ball and disk apparatus was used to investigate the lubricant replenishment of an elastohydrodynamically lubricated point contact. This replenishment of the contact is crucial for building up a lubricating film. Whereas lubricating oil manages to achieve replenishment, lubricating grease appears not to achieve this, with lubricant starvation and a dramatic decrease in film thickness as a result. The distribution of grease around the contact was studied using normal and high-speed video. The movements of grease in the vicinity of the contact could be seen by adding molybdenum disulfide particles to the grease. A recording was then made, using highspeed video recording. The overall cavitation regions were studied using an ordinary video camera and grease without particles. On the basis of the results, possible lubricating grease replenishment mechanisms are discussed. The resulting film thickness was also compared with theoretical predictions using the Hamrock and Dowson starvation criterion, assuming negligible replenishment. The measured film thickness was larger than the predicted, which indicated that some replenishment occurs. In the case of an ordinary thrust ball bearing, replenishment was found to rely on the spin motion of the balls.

Oil Film Thickness and Pressure Distribution in Elastohydrodynamic Point Contacts

1982 ◽  
Vol 24 (4) ◽  
pp. 173-182 ◽  
Author(s):  
A. Mostofi ◽  
R. Gohar
Keyword(s):  
Contact Problem ◽  
Film Thickness ◽  
Numerical Solutions ◽  
Point Contact ◽  
Point Contacts ◽  
Rolling Velocity ◽  
Oil Film ◽  
Static Contact ◽  
Theoretical Predictions ◽  
Interferometry Method

In this paper, a general numerical solution to the elastohydrodynamic point contact problem is presented for moderate loads and material parameters. Isobars, contours and regression formulae describe how pressure and oil film thickness vary with geometry, material properties, load, and squeeze velocity, when the rolling velocity vector is at various angles to the static contact ellipse long axis. In addition, the EHL behaviour under spin is examined. The theoretical predictions of film thickness compare favourably with other numerical solutions to the point contact problem, as well as with experimental results which use the optical interferometry method to find film thickness and

Elastohydrodynamic Lubrication of Heavily Loaded Circular Contacts

1989 ◽  
Vol 203 (2) ◽  
pp. 133-148 ◽  
Author(s):  
C C Kweh ◽  
H P Evans ◽  
R W Snidle
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Engineering Practice ◽  
Experimental Measurements ◽  
Lubricant Film Thickness ◽  
Wide Range ◽  
Theoretical Predictions ◽  
Steel Surfaces ◽  
Maximum Contact ◽  
Contact Pressures

The paper is concerned with theoretical analysis and experimental measurement of lubricant film thickness in heavily loaded elastohydrodynamic contacts in which the area of elastic deformation is approximately circular. The inverse elastohydrodynamic technique for numerical analysis of contacts of this type described by Evans and Snidle(9) has been used to produce solutions covering a wide range of conditions representative of engineering practice. Detailed solutions for film thickness and pressure have been obtained for conditions giving rise to maximum contact pressures of up to 4.1 GPa with steel surfaces and a mineral oil lubricant. On the basis of these results charts for film thickness have been constructed using the non-dimensional groups proposed by Moes and Bosma(12). Experimental measurements of film thickness have been made using the optical interferometry technique. The conditions used in the experiments have been numerically analysed to provide a direct comparison between theory and experiment. The comparison shows excellent agreement between the theoretical predictions and corresponding experimental measurements.

scholarly journals Effect of an Improved Yasutomi Pressure-Viscosity Relationship on the Elastohydrodynamic Line Contact Problem

2013 ◽  
Vol 2013 ◽  
pp. 1-7
Author(s):  
Vincenzo Petrone ◽  
Adolfo Senatore ◽  
Vincenzo D'Agostino
Keyword(s):  
High Pressure ◽  
Film Thickness ◽  
Free Volume ◽  
Experimental Studies ◽  
Line Contact ◽  
Volume Model ◽  
Free Volume Model ◽  
Pressure Area ◽  
New Formulation ◽  
Lubricant Viscosity

This paper presents the application of an improved Yasutomi correlation for lubricant viscosity at high pressure in a Newtonian elastohydrodynamic line contact simulation. According to recent experimental studies using high pressure viscometers, the Yasutomi pressure-viscosity relationship derived from the free-volume model closely represents the real lubricant piezoviscous behavior for the high pressure typically encountered in elastohydrodynamic applications. However, the original Yasutomi correlation suffers from the appearance of a zero in the function describing the pressure dependence of the relative free volume thermal expansivity. In order to overcome this drawback, a new formulation of the Yasutomi relation was recently developed by Bair et al. This new function removes these concerns and provides improved precision without the need for an equation of state. Numerical simulations have been performed using the improved Yasutomi model to predict the lubricant pressure-viscosity, the pressure distribution, and the film thickness behavior in a Newtonian EHL simulation of a squalane-lubricated line contact. This work also shows that this model yields a higher viscosity at the low-pressure area, which results in a larger central film thickness compared with the previous piezoviscous relations.

Effect of Rolling Velocity and Maximum Hertzian Pressure on Fluid Film in Steady State EHL Line Contact with Rough Surface and Linear Piezoviscosity

2014 ◽  
Vol 592-594 ◽  
pp. 1371-1375
Author(s):  
Nitesh Talekar ◽  
Punit Kumar
Keyword(s):  
Surface Roughness ◽  
Steady State ◽  
Film Thickness ◽  
Rough Surface ◽  
Computer Code ◽  
Fluid Film ◽  
Line Contact ◽  
Rolling Velocity ◽  
Load Carrying ◽  
Lubricated Contact

Consideration of surface roughness in steady state EHL line contact is the first step towards understanding the lubrication of rough surface problem. Current paper investigates the use of sinusoidal waviness in the contact; more precisely it gives performance of real fluid in EHL line contact. The effect of various parameters like rolling velocity (U) and maximum Hertzian pressure (ph) on surface roughness by using properties of linear and exponential piezo-viscosity is taken into consideration to evaluate behavior of pressure distribution of load carrying fluid film and film thickness. Full isothermal, Newtonian simulation of EHL problem gives described effects. Spiking or fluctuation of pressure and film thickness curves is expected to show presence of irregularities on the surface chosen and amount of fluctuation depends on certain parameters and intensity of irregularities present. Rolling side domain of-4.5 ≤ X ≤ 1.5 with grid size ∆X=0.01375 is selected. A computer code is developed to solve Reynolds equation, which governs the generation of pressure in the lubricated contact zone is discritized and solved along with load balance equation using Newton-Raphson technique.

scholarly journals A thermal resistances-based approach for thermal-elastohydrodynamic calculations in point contacts

2017 ◽  
Vol 232 (11) ◽  
pp. 2088-2102 ◽  
Author(s):  
Eduardo de la Guerra Ochoa ◽  
Javier Echávarri Otero ◽  
Enrique Chacón Tanarro ◽  
Benito del Río López
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Thermal Effects ◽  
Good Accuracy ◽  
Computational Cost ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
New Approach ◽  
Ball On Disc

This article presents a thermal resistances-based approach for solving the thermal-elastohydrodynamic lubrication problem in point contact, taking the lubricant rheology into account. The friction coefficient in the contact is estimated, along with the distribution of both film thickness and temperature. A commercial tribometer is used in order to measure the friction coefficient at a ball-on-disc point contact lubricated with a polyalphaolefin base. These data and other experimental results available in the bibliography are compared to those obtained by using the proposed methodology, and thermal effects are analysed. The new approach shows good accuracy for predicting the friction coefficient and requires less computational cost than full thermal-elastohydrodynamic simulations.

Prediction of Ball Motion in High-Speed Thrust-Loaded Ball Bearings

1976 ◽  
Vol 98 (3) ◽  
pp. 463-469 ◽  
Author(s):  
C. R. Gentle ◽  
R. J. Boness
Keyword(s):  
Computer Program ◽  
High Speed ◽  
Ball Bearing ◽  
Viscoelastic Behavior ◽  
Specific Situation ◽  
Fluid Models ◽  
Ball Bearings ◽  
Theoretical Predictions ◽  
Ball Motion

This paper describes the development of a computer program used to analyze completely the motion of a ball in a high-speed, thrust-loaded ball bearing. Particular emphasis is paid to the role of the lubricant in governing the forces and moments acting on each ball. Expressions for these forces due to the rolling and sliding of the ball are derived in the light of the latest fluid models, and estimates are also made of the cage forces applicable in this specific situation. It is found that only when lubricant viscoelastic behavior is considered do the theoretical predictions agree with existing experimental evidence.

scholarly journals The Effects of Artificially-Produced Defects on the Film Thickness Distribution in Sliding EHD Point Contacts

1982 ◽  
Vol 104 (3) ◽  
pp. 365-375 ◽  
Author(s):  
C. Cusano ◽  
L. D. Wedeven
Keyword(s):  
Film Thickness ◽  
Contact Region ◽  
Thickness Distribution ◽  
Point Contact ◽  
Optical Interferometry ◽  
Point Contacts ◽  
Thickness Profile ◽  
Inlet Region

The effects of artificially-produced dents and grooves on the elastohydrodynamic (EHD) film thickness profile in a sliding point contact are investigated by means of optical interferometry. The defects, formed on the surface of a highly polished ball, are held stationary at various locations within and in the vicinity of the contact region while the disk is rotating. It is shown that the defects, having a geometry similar to what can be expected in practice, can dramatically change the film thickness which exists when no defects are present in or near the contact. This change in film thickness is mainly a function of the position of the defects in the inlet region, the geometry of the defects, the orientation of the defects in the case of grooves, and the depth of the defect relative to the central film thickness.

Sign in / Sign up

Export Citation Format

Share Document