The Effect of Interaction Between Wakes From Blade Rows in an Axial Flow Compressor on the Noise Generated by Blade Interaction

1972 ◽  
Vol 94 (4) ◽  
pp. 241-248 ◽  
Author(s):  
G. J. Walker ◽  
A. R. Oliver
Keyword(s):  
Sound Pressure Level ◽  
Rotor Blade ◽  
Sound Pressure ◽  
Axial Flow ◽  
Pressure Level ◽  
Rotor Blades ◽  
Hot Wire ◽  
Velocity Defect ◽  
Axial Flow Compressor ◽  
Flow Compressor

The effect of interaction between the wakes from one row of blades and the boundary layers and wakes of the next row of blades downstream has been measured in an axial flow compressor by hot wire signals displayed on a CRO screen synchronized with the rotor. It is shown that the two sets of wakes can be made to mutually cancel the greater part of the velocity defect in each at certain points. Proper choice of axial and circumferential position of alternate rows of stationary blades so that the downstream row is in the middle of the wake street from the upstream row allows the velocity defect normally in the rotor wakes to be thus cancelled at the position of the stator and considerably reduces the noise produced at the rotor blade passing frequency by the rotor wakes on the stator. The effect of stator wakes on rotor blades downstream of the first can be similarly reduced by lining up blades in successive rotor rows. The deductions are confirmed by measurements of sound pressure level.

Analysis of the Noise Level Generated by Axial Flow Fan Composed of Radial-Bladed Centrifugal Rotor

2014 ◽  
Author(s):  
S. S. Borges ◽  
R. Barbieri ◽  
P. S. B. Zdanski
Keyword(s):  
Sound Pressure Level ◽  
Sound Pressure ◽  
Axial Flow ◽  
Acoustic Resonance ◽  
Pressure Level ◽  
Resonance Mode ◽  
Numerical Techniques ◽  
Cooling Systems ◽  
Centrifugal Fans ◽  
Motor Cooling

The objective of this work is to present, by means of experimental, analytical and numerical techniques that sound pressure level generated by radial-bladed centrifugal fans of electric motor cooling systems may be expressed by a logarithmical ratio of the peripheral velocity of rotor, volumetric flow and efficiency of the fan. The proposed methodology proved to be efficient and simple in the prediction of generated noise by radial-bladed centrifugal fans of TEFC motors with accuracy of ± 3 dB. In addition, the acoustic resonance mode of the fan cavity were determined by means of numerical simulations, which its results were validated through experiments using waterfall spectrum.

Noise Reduction Analysis of Electronic Device Cooling Fan With Duct and Its Application Under Variable Working Conditions

2021 ◽  
Author(s):  
Zonghan Sun ◽  
Jie Tian ◽  
Grzegorz Liśkiewicz ◽  
Zhaohui Du ◽  
Hua Ouyang
Keyword(s):  
Noise Reduction ◽  
Working Conditions ◽  
Sound Pressure Level ◽  
Sound Pressure ◽  
Reduction Method ◽  
Axial Flow ◽  
Pressure Level ◽  
Inlet Flow ◽  
Cooling Fan ◽  
Inlet Duct

Abstract A noise reduction method for axial flow fans using a short inlet duct is proposed. The pattern of noise reduction imposed by the short inlet duct on the axial flow cooling fan under variable working conditions was experimentally and numerically examined. A 2-cm inlet duct was found to reduce tonal noise. As the tip Mach number of the fan increased from 0.049 to 0.156, the reduction in the total average sound pressure level at 1 m from the fan increased from 0.8 dB(A) to 4.3 dB(A), and further achieved 4.8 dB(A) when a 1-cm inlet duct was used. The steady computational fluid dynamics (CFD) showed that the inlet duct has little effect on the aerodynamic performance of the fan. The results of the full passage unsteady calculation at the maximum flow rate showed that the duct has a significant influence on the suction vortexes caused by the inlet flow non-uniformity. The suction vortexes move upstream to weaken the interaction with the rotor blades, which significantly reduces the pulsating pressure on the blades. The sound pressure level (SPL) at the blade passing frequency (BPF) contributed by the thrust force was calculated to reduce by 36 dB at a 135° observer angle, reflecting the rectification effect of the duct on the non-uniform inlet flow and the improvement in characteristics of the noise source. The proper orthogonal decomposition (POD) of the static pressure field on the blades verified that the main spatial mode is more uniformly distributed due to the duct, and energy owing to the rotor-inlet interaction decreases. A speed regulation strategy for the cooling fan with short inlet duct is proposed, which provides guidance for the application of this noise reduction method.

Influence of Rain Ingestion on the Endwall Treatment in an Axial Flow Compressor

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Jichao Li ◽  
Juan Du ◽  
Mingzhen Li ◽  
Feng Lin ◽  
Hongwu Zhang ◽  
...  
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Pressure Rise ◽  
Water Film ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Water Ingestion ◽  
Blade Row ◽  
Flow Compressor ◽  
The Stability

The effects of water ingestion on the performance of an axial flow compressor are experimentally studied with and without endwall treatment. The background to the work is derived from the assessment of airworthiness for an aero-engine. The stability-enhancing effects with endwall treatments under rain ingestion are not previously known. Moreover, all the endwall treatments are designed under dry air conditions in the compressor. Water ingestion at 3% and 5% relative to the design mass flow proposed in the airworthiness standard are applied to initially investigate the effects on the performance under smooth casing (SC). Results show that the water ingestions are mainly located near the casing wall after they move through the rotor blade row. The pressure rise coefficient increases, efficiency declines, and torque increases under the proposed water ingestion. The increase of the inlet water increases the thickness of the water film downstream the rotor blade row and aggravates the adverse effects on the performances. Subsequently, three endwall treatments, namely circumferential grooves, axial slots, and hybrid slots–grooves, are tested with and without water ingestion. Compared with no water ingestion, the circumferential grooves basically have no resistance to the water ingestion. The axial slots best prevent the drop of the pressure rise coefficient induced by water ingestion, and hybrid slots–grooves are the second-best place owing to the contribution of the front axial slots. Therefore, the hybrid slots–grooves can not only extend the stall margin with less efficiency penalty compared with axial slots, but also prevent rain ingestion from worsening the compressor performance.

Experimental and Numerical Investigation of Blades Effect on Aerodynamic Performance of Small Axial Flow Fan

2011 ◽  
Author(s):  
Li Zhang ◽  
Yingzi Jin ◽  
Yi Zhao ◽  
Pin Liu
Keyword(s):  
Flow Field ◽  
Sound Pressure Level ◽  
Sound Pressure ◽  
Axial Flow ◽  
Aerodynamic Performance ◽  
Pressure Level ◽  
Aerodynamic Noise ◽  
Blade Number ◽  
Small Axial Flow Fan ◽  
Fan Blade

To explore the effect of blade numbers on aerodynamic performance and noise of small axial flow fan, the steady flow field and the unsteady flow field of fan models with 6 different blade numbers (such as 5, 7, 9, 11, 13, 15) are numerically calculated. Then the internal flow distribution, static characteristic and aerodynamic noise are analyzed among six different fan models. The analysis results show: (1)Total pressure and efficiency generally maintain the trend of first increasing and then decreasing with increasing blade numbers, and it is the maximum when fan blade number is 11. The flow rate coupled with the maximum efficiency has never changed with increasing the blade numbers. (2)With increasing blade numbers, overall sound pressure level of the aerodynamic noise is gradually decreasing near the outlet of fan tip, while it is first decreasing and then increasing before decreasing again at 1 meter away from the central axis of the impeller along the outlet. When fan blade number is 11, overall sound pressure level of the aerodynamic noise is the greatest. Furthermore, the aerodynamic performance tests of fan models with 6 different blade numbers are carried out, the results of between the tests and the numerical calculations are roughly consistent. The research results will provide the proof of the parameter optimization and the structure design for high performance and low noise small axial fans.

Water Film Formation on an Axial Flow Compressor Rotor Blade

2008 ◽  
Author(s):  
Theoklis Nikolaidis ◽  
Periclis Pilidis ◽  
J. A. Teixeira ◽  
V. Pachidis
Keyword(s):  
Rotor Blade ◽  
Guide Vane ◽  
Axial Flow ◽  
Water Film ◽  
Inlet Guide Vane ◽  
Computational Domain ◽  
Axial Flow Compressor ◽  
Water Ingestion ◽  
Compressor Rotor ◽  
Flow Compressor

A numerical approach was used to evaluate the liquid water film thickness and its motion on an axial flow compressor rotor blade under water ingestion conditions. By post-processing blading data and using computer programs to create the blades and their computational grid, the global computational domain of the first stage of an axial flow compressor was built. The flow field within the domain was solved by CFX-Tascflow, which is a commercial CFD code commonly used in turbomachinery. The computational domain consists of an extended inlet, an inlet guide vane, a rotor and a stator blade. Having solved the flow field at Design Point, the inlet guide vane blade was re-positioned to account for changes in idle speed. At that speed, the effects of water ingestion are expected to be more significant on gas turbine engine performance. Several cases with water ingestion were studied, changing parameters like water mass and compressor rotational speed. A FORTRAN computer program was created to calculate the water film height and speed. The extra torque needed by the compressor to keep running at the same rotational speed, was also calculated. The considerable increase in torque was confirmed by experimental observations according to which water ingestion had a detrimental effect on gas turbine operation.

The Influence of Blade Number Ratio and Blade Row Spacing on Axial-Flow Compressor Stator Blade Dynamic Load and Stage Sound Pressure Level

1982 ◽  
Vol 104 (3) ◽  
pp. 633-641 ◽  
Author(s):  
H. E. Gallus ◽  
H. Grollius ◽  
J. Lambertz
Keyword(s):  
Sound Pressure Level ◽  
Sound Pressure ◽  
Dynamic Pressure ◽  
Axial Flow ◽  
Fixed Number ◽  
Pressure Level ◽  
Wake Flow ◽  
Pressure Probe ◽  
Blade Row ◽  
Stator Blade

In axial-flow turbomachines considerable dynamic blade loads and noise production occur as a result of the unsteady blade row interaction between rotor and stator blades. This paper presents results of midspan measurements of the dynamic pressure distribution on the stator blade surface (fixed number of blades) for various rotor-blade numbers and various axial clearances between rotor and stator. For this purpose, one stator blade had been provided with eleven semiconductor pressure transducers in the midspan section. Simultaneously, the sound pressure level was measured at two axial distances downstream of the stator by four condensator microphones distributed along the circumference in each of the two sections and mounted flush with the wall surface. The wake-flow distribution downstream of the rotor could be obtained by a rotating three-hole pressure probe. The results of the corresponding dynamic pressure-measurements and noise measurements are discussed and compared with results from theory.

scholarly journals Characteristic Factors of a Compressor Rotor in Comparison With Two-Dimensional Cascade Data

1986 ◽  
Author(s):  
H. Pfeil ◽  
J. Sieber
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Processing System ◽  
Two Dimensional ◽  
Hot Wire ◽  
Data Processing System ◽  
Wire Probe ◽  
Compressor Rotor ◽  
Profile Losses ◽  
Flow Compressor

The performance of a blade in an axial-flow compressor rotor is compared with the performance in a two-dimensional cascade. Using a stationary hot-wire probe and a data processing system the velocity profiles across the rotor wakes were measured in order to calculate the profile losses and the lift coefficients of the rotor blade.

Effect of Blade Numbers on Aerodynamic Performance and Noise of Small Axial Flow Fan

2011 ◽  
Vol 199-200 ◽  
pp. 796-800
Author(s):  
Li Zhang ◽  
Ying Zi Jin
Keyword(s):  
Flow Field ◽  
Sound Pressure Level ◽  
Sound Pressure ◽  
Axial Flow ◽  
Aerodynamic Performance ◽  
Pressure Level ◽  
Aerodynamic Noise ◽  
Blade Number ◽  
Small Axial Flow Fan ◽  
Fan Blade

To more fully explore the effect of blade numbers on aerodynamic performance and noise of small axial flow fan, some solutions are adopted to obtain the parameters’ distribution of the flow field.Firstly, the standard k-ε turbulence model is used to calculate the steady flow field of six different fan blades(such as 5,7,9,11,13,15) , and the SIMPLE algorithm is applied to couple vecolity and pressure. Secondly, the large eddy simulation in conjunction with the FH-W noise model are used to compute the unsteady flow field and noise. Finally, the experimental results verify that the calculation methods of steady flow field and unsteady flow field are correct. The conclusions show: (1)Total pressure and efficiency generally maintain the trend of firstly increasing and then decreasing with increasing the blade numbers, and it is the greatest when fan blade number is 11. The flow rate coupled with the maximum efficiency has never changed with increasing the blade numbers. (2)With the increasing blades, overall sound pressure level of the aerodynamic noise is gradually decreasing near the outlet of fan tip, while it is firstly decreasing and then increasing before decreasing again 1 meter away from the central axis of the impeller along the outlet. When fan blade number is 11, overall sound pressure level of the aerodynamic noise is the greatest.

Sign in / Sign up

Export Citation Format

Share Document