Investigation of Thermal Effects on Weapon System Components

1983 ◽  
Vol 105 (2) ◽  
pp. 227-231
Author(s):  
J. J. Labra
Keyword(s):  
Thermal Effects ◽  
Test Chamber ◽  
Three Dimensional ◽  
General Purpose ◽  
Structural Components ◽  
Design Changes ◽  
Environmental Test ◽  
Cause Of Failure ◽  
Computer Based ◽  
Complex Structural

A three-dimensional stress analysis of a 30-mm machine gun component on the Harrier Aircraft was conducted to investigate the cause of observed fractures. The analysis was made using a general purpose finite element computer program and a laboratory environmental test chamber. Based on this study, the probable cause of failure was identified and, as a result, the component manufacturer is considering possible design changes to alleviate this problem in further production. The study clearly demonstrates that computer-based technology can be successfully used in investigating causes of failure in complex structural components.

Study of Low-Load Industrial Robot

2013 ◽  
Vol 774-776 ◽  
pp. 1409-1413
Author(s):  
Bei Yu Chen
Keyword(s):  
Technological Innovation ◽  
Industrial Robot ◽  
Virtual Prototyping ◽  
Three Dimensional ◽  
General Purpose ◽  
Industrial Robots ◽  
Precision Machining ◽  
Structural Components ◽  
Low Load ◽  
Increasing Demand

In recent years, China's increasing demand for precision machining and auxiliary processing, technological innovation is increasingly urgent. After a summary and integration advantages of virtual prototyping and computer-aided software, developed a General Purpose low-load industrial robots. In this paper, the D-H method in MATLAB to establish a three-dimensional diagram of the industrial robot. Using ANSYS to do a check of the stiffness of the important components of the industrial robot mechanical systems. Finally, after the structure static analysis and verification, to improve the design of the structural components of the robot. Obtained according to the repeatedly comparison of the overall shape of variable verification data, which prove that the design is correct.

scholarly journals A digital patient for computer-aided prosthesis design

2013 ◽  
Vol 3 (2) ◽  
pp. 20120082 ◽  
Author(s):  
Giorgio Colombo ◽  
Giancarlo Facoetti ◽  
Caterina Rizzi
Keyword(s):  
Three Dimensional ◽  
General Purpose ◽  
Three Dimensional Model ◽  
Anthropometric Measures ◽  
Simulation Tools ◽  
Computer Aided ◽  
Lower Limb Prosthesis ◽  
Computer Based ◽  
Set Up ◽  
General Architecture

This article concerns the design of lower limb prosthesis, both below and above knee. It describes a new computer-based design framework and a digital model of the patient around which the prosthesis is designed and tested in a completely virtual environment. The virtual model of the patient is the backbone of the whole system, and it is based on a biomechanical general-purpose model customized with the patient's characteristics (e.g. anthropometric measures). The software platform adopts computer-aided and knowledge-guided approaches with the goal of replacing the current development process, mainly hand made, with a virtual one. It provides the prosthetics with a set of tools to design, configure and test the prosthesis and comprehends two main environments: the prosthesis modelling laboratory and the virtual testing laboratory. The first permits the three-dimensional model of the prosthesis to be configured and generated, while the second allows the prosthetics to virtually set up the artificial leg and simulate the patient's postures and movements, validating its functionality and configuration. General architecture and modelling/simulation tools for the platform are described as well as main aspects and results of the experimentation.

scholarly journals Computer Simulation of Hybrid Integrated Circuits Including Combined Electrical and Thermal Effects

1983 ◽  
Vol 10 (2-3) ◽  
pp. 171-176 ◽  
Author(s):  
Carl R. Zimmer
Keyword(s):  
Integrated Circuits ◽  
Thermal Effects ◽  
Thermal Environment ◽  
Variable Temperature ◽  
Three Dimensional ◽  
General Purpose ◽  
Voltage Source ◽  
Thermal Coupling ◽  
Analysis Programme ◽  
Environment Parameters

This paper describes the application of a modern general purpose network analysis programme SPICE2 for the electrothermal analysis of hybrid integrated circuits. Self thermal coupling effects are modelled using the non-linear dependent current and voltage source capability in this programme, together with thermal environment parameters obtained from a three-dimensional thermal analysis program. Although numerical results are given by a bipolar transistor, the method is also applicable to monolithic integrated circuits and to resistors with variable temperature coefficients as power dissipating elements.

Three-Dimensional Reconstruction of Two Forms of the Chaperonin GRO EL

1990 ◽  
Vol 48 (1) ◽  
pp. 258-259
Author(s):  
J.L. Carrascosa ◽  
G. Abella ◽  
S. Marco ◽  
M. Muyal ◽  
J.M. Carazo
Keyword(s):  
Three Dimensional ◽  
The Other ◽  
Two Dimensional ◽  
Series Method ◽  
Three Dimensional Reconstruction ◽  
Structural Components ◽  
E Coli ◽  
Dimensional Reconstruction ◽  
Morphogenetic Factors ◽  
Tilt Series

Chaperonins are a class of proteins characterized by their role as morphogenetic factors. They trantsiently interact with the structural components of certain biological aggregates (viruses, enzymes etc), promoting their correct folding, assembly and, eventually transport. The groEL factor from E. coli is a conspicuous member of the chaperonins, as it promotes the assembly and morphogenesis of bacterial oligomers and/viral structures.We have studied groEL-like factors from two different bacteria:E. coli and B.subtilis. These factors share common morphological features , showing two different views: one is 6-fold, while the other shows 7 morphological units. There is also a correlation between the presence of a dominant 6-fold view and the fact of both bacteria been grown at low temperature (32°C), while the 7-fold is the main view at higher temperatures (42°C). As the two-dimensional projections of groEL were difficult to interprete, we studied their three-dimensional reconstruction by the random conical tilt series method from negatively stained particles.

scholarly journals Radial Turbine Design for Solar Chimney Power Plants

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 674
Author(s):  
Paul Caicedo ◽  
David Wood ◽  
Craig Johansen
Keyword(s):  
Power Plants ◽  
Reference Frames ◽  
Three Dimensional ◽  
Discrete Ordinates ◽  
Large Area ◽  
Solar Chimney ◽  
Cfd Simulations ◽  
Radial Turbine ◽  
Design Changes ◽  
Turbine Design

Solar chimney power plants (SCPPs) collect air heated over a large area on the ground and exhaust it through a turbine or turbines located near the base of a tall chimney to produce renewable electricity. SCPP design in practice is likely to be specific to the site and of variable size, both of which require a purpose-built turbine. If SCPP turbines cannot be mass produced, unlike wind turbines, for example, they should be as cheap as possible to manufacture as their design changes. It is argued that a radial inflow turbine with blades made from metal sheets, or similar material, is likely to achieve this objective. This turbine type has not previously been considered for SCPPs. This article presents the design of a radial turbine to be placed hypothetically at the bottom of the Manzanares SCPP, the only large prototype to be built. Three-dimensional computational fluid dynamics (CFD) simulations were used to assess the turbine’s performance when installed in the SCPP. Multiple reference frames with the renormalization group k-ε turbulence model, and a discrete ordinates non-gray radiation model were used in the CFD simulations. Three radial turbines were designed and simulated. The largest power output was 77.7 kW at a shaft speed of 15 rpm for a solar radiation of 850 W/m2 which exceeds by more than 40 kW the original axial turbine used in Manzanares. Further, the efficiency of this turbine matches the highest efficiency of competing turbine designs in the literature.

scholarly journals A computer-based approach for developing linamarase inhibitory agents

2020 ◽  
Vol 5 (7) ◽  
Author(s):  
Lucas Paul ◽  
Celestin N. Mudogo ◽  
Kelvin M. Mtei ◽  
Revocatus L. Machunda ◽  
Fidele Ntie-Kang
Keyword(s):  
Structure Elucidation ◽  
Three Dimensional ◽  
Data Bank ◽  
Competitive Inhibitor ◽  
Industrial Applications ◽  
Dimensional Structure ◽  
Full Understanding ◽  
The Poor ◽  
Computer Based ◽  
Inhibitory Agents

AbstractCassava is a strategic crop, especially for developing countries. However, the presence of cyanogenic compounds in cassava products limits the proper nutrients utilization. Due to the poor availability of structure discovery and elucidation in the Protein Data Bank is limiting the full understanding of the enzyme, how to inhibit it and applications in different fields. There is a need to solve the three-dimensional structure (3-D) of linamarase from cassava. The structural elucidation will allow the development of a competitive inhibitor and various industrial applications of the enzyme. The goal of this review is to summarize and present the available 3-D modeling structure of linamarase enzyme using different computational strategies. This approach could help in determining the structure of linamarase and later guide the structure elucidation in silico and experimentally.

scholarly journals Extrusion Based 3D Printing of Sustainable Biocomposites from Biocarbon and Poly(trimethylene terephthalate)

Molecules ◽  
2021 ◽  
Vol 26 (14) ◽  
pp. 4164
Author(s):  
Elizabeth Diederichs ◽  
Maisyn Picard ◽  
Boon Peng Chang ◽  
Manjusri Misra ◽  
Amar Mohanty
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Surface Finish ◽  
Three Dimensional ◽  
Morphological Properties ◽  
Great Promise ◽  
Structural Components ◽  
Computer Aided ◽  
Trimethylene Terephthalate ◽  
Optimal Quantity

Three-dimensional (3D) printing manufactures intricate computer aided designs without time and resource spent for mold creation. The rapid growth of this industry has led to its extensive use in the automotive, biomedical, and electrical industries. In this work, biobased poly(trimethylene terephthalate) (PTT) blends were combined with pyrolyzed biomass to create sustainable and novel printing materials. The Miscanthus biocarbon (BC), generated from pyrolysis at 650 °C, was combined with an optimized PTT blend at 5 and 10 wt % to generate filaments for extrusion 3D printing. Samples were printed and analyzed according to their thermal, mechanical, and morphological properties. Although there were no significant differences seen in the mechanical properties between the two BC composites, the optimal quantity of BC was 5 wt % based upon dimensional stability, ease of printing, and surface finish. These printable materials show great promise for implementation into customizable, non-structural components in the electrical and automotive industries.

scholarly journals Exceptional Mechanical Properties and Heat Resistance of Photocurable Bismaleimide Ink for 3D Printing

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1708
Author(s):  
Wenqiang Hua ◽  
Qilang Lin ◽  
Bo Qu ◽  
Yanyu Zheng ◽  
Xiaoying Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Heat Resistance ◽  
Three Dimensional ◽  
Mechanical And Thermal Properties ◽  
Amino Group ◽  
Building Models ◽  
Fast Processing ◽  
Forming Precision ◽  
Complex Structural

Photosensitive resins used in three-dimensional (3D) printing are characterized by high forming precision and fast processing speed; however, they often possess poor mechanical properties and heat resistance. In this study, we report a photocurable bismaleimide ink with excellent comprehensive performance for stereolithography (SLA) 3D printing. First, the main chain of bismaleimide with an amino group (BDM) was synthesized, and then, the glycidyl methacrylate was grafted to the amino group to obtain the bismaleimide oligomer with an unsaturated double bond. The oligomers were combined with reaction diluents and photo-initiators to form photocurable inks that can be used for SLA 3D printing. The viscosity and curing behavior of the inks were studied, and the mechanical properties and heat resistance were tested. The tensile strength of 3D-printed samples based on BDM inks could reach 72.6 MPa (166% of that of commercial inks), glass transition temperature could reach 155 °C (205% of that of commercial inks), and energy storage modulus was 3625 MPa at 35 °C (327% of that of commercial inks). The maximum values of T-5%, T-50%, and Tmax of the 3D samples printed by BDM inks reached 351.5, 449.6, and 451.9 °C, respectively. These photocured BDM inks can be used to produce complex structural components and models with excellent mechanical and thermal properties, such as car parts, building models, and pipes.

Analysis of Single- and Two-Phase Flows in Turbopump Inducers

1967 ◽  
Vol 89 (4) ◽  
pp. 577-586 ◽  
Author(s):  
P. Cooper
Keyword(s):  
Equation Of State ◽  
Flow Field ◽  
Thermal Effects ◽  
Single Phase ◽  
Fluid Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Recent Theory ◽  
Two Phase ◽  
Overall Efficiency

A model is developed for analytically determining pump inducer performance in both the single-phase and cavitating flow regimes. An equation of state for vaporizing flow is used in an approximate, three-dimensional analysis of the flow field. The method accounts for losses and yields internal distributions of fluid pressure, velocity, and density together with the resulting overall efficiency and pressure rise. The results of calculated performance of two sample inducers are presented. Comparison with recent theory for fluid thermal effects on suction head requirements is made with the aid of a resulting dimensionless vaporization parameter.

Optimization of the Wrist Pin End of an Automobile Engine Connecting Rod With an Interference Fit

1990 ◽  
Vol 112 (3) ◽  
pp. 406-412 ◽  
Author(s):  
Vijay Sarihan ◽  
Ji Oh Song
Keyword(s):  
Finite Element ◽  
Optimum Design ◽  
Three Dimensional ◽  
Stress Singularity ◽  
Design Strategy ◽  
Structural Components ◽  
Connecting Rod ◽  
Fem Model ◽  
Automobile Engine ◽  
Interference Fit

Current design procedures for complicated three-dimensional structural components with component interactions may not necessarily result in optimum designs. The wrist pin end design of the connecting rod with an interference fit is governed by the stress singularity in the region where the wrist pin breaks contact with the connecting rod. Similar problems occur in a wide variety of structural components which involve interference fits. For a better understanding of the problems associated with obtaining optimum designs for this important class of structural interaction only the design problems associated with the wrist pin end of the rod are addressed in this study. This paper demonstrates a procedure for designing a functional and minimum weight wrist pin end of an automobile engine connecting rod with an interference fit wrist pin. Current procedures for Finite Element Method (FEM) model generation in complicated three-dimensional components are very time consuming especially in the presence of stress singularities. Furthermore the iterative nature of the design process makes the process of developing an optimum design very expensive. This design procedure uses a generic modeler to generate the FEM model based on the values of the design variables. It uses the NASTRAN finite element program for structural analysis. A stress concentration factor approach is used to obtain realistic stresses in the region of the stress singularity. For optimization, the approximate optimization strategy in the COPES/CONMIN program is used to generate an approximate design surface, determine the design sensitivities for constrained function minimization and obtain the optimum design. This proposed design strategy is fully automated and requires only an initial design to generate the optimum design. It does not require analysis code modifications to compute the design sensitivities and requires very few costly NASTRAN analyses. The connecting rod design problem was solved as an eight design variable problem with five constraints. A weight reduction of nearly 27 percent was achieved over an existing design and required only thirteen NASTRAN analyses. It is felt that this design strategy can be effectively used in an engineering environment to generate optimum designs of complicated three-dimensional components.

Sign in / Sign up

Export Citation Format

Share Document