Parametric Study of Salt Gradient Solar Ponds

1986 ◽  
Vol 108 (1) ◽  
pp. 75-77 ◽  
Author(s):  
R. S. Beniwal ◽  
N. S. Saxena ◽  
R. C. Bhandari
Keyword(s):  
Thermal Conductivity ◽  
Mathematical Model ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Parametric Study ◽  
Heat Losses ◽  
Insulating Materials ◽  
Solar Ponds ◽  
Solar Pond ◽  
Salt Gradient

A mathematical model for efficiency of a salt gradient solar pond is described. Heat losses from the bottom of the pond have been calculated, and the results for the effective thermal conductivity with the thicknesses of various insulating materials have been presented. The effect of the ground thermal resistance on the efficiency of the pond for different values of ΔT/So have also been shown.

Determining the thermal resistance of a highly insulated wall containing vacuum insulation panels through experimental, calculation and numerical simulation methods

2020 ◽  
pp. 174425912098003
Author(s):  
Travis V Moore ◽  
Cynthia A. Cruickshank ◽  
Ian Beausoleil-Morrison ◽  
Michael Lacasse
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Edge Effect ◽  
3D Simulation ◽  
Simulation Methods ◽  
Zone Method ◽  
Vacuum Insulation ◽  
Thermal Bridges ◽  
Wall Assembly

The purpose of this paper is to investigate the potential for calculation methods to determine the thermal resistance of a wall system containing vacuum insulation panels (VIPs) that has been experimentally characterised using a guarded hot box (GHB) apparatus. The VIPs used in the wall assembly have not been characterised separately to the wall assembly, and therefore exact knowledge of the thermal performance of the VIP including edge effect is not known. The calculations and simulations are completed using methods found in literature as well as manufacturer published values for the VIPs to determine the potential for calculation and simulation methods to predict the thermal resistance of the wall assembly without the exact characterisation of the VIP edge effect. The results demonstrate that disregarding the effect of VIP thermal bridges results in overestimating the thermal resistance of the wall assembly in all calculation and simulation methods, ranging from overestimates of 21% to 58%. Accounting for the VIP thermal bridges using the manufacturer advertised effective thermal conductivity of the VIPs resulted in three methods predicting the thermal resistance of the wall assembly within the uncertainty of the GHB results: the isothermal planes method, modified zone method and the 3D simulation. Of these methods only the 3D simulation can be considered a potential valid method for energy code compliance, as the isothermal planes method requires too drastic an assumption to be valid and the modified zone method requires extrapolating the zone factor beyond values which have been validated. The results of this work demonstrate that 3D simulations do show potential for use in lieu of guarded hot box testing for predicting the thermal resistance of wall assemblies containing both VIPs and steel studs. However, knowledge of the VIP effective thermal conductivity is imperative to achieve reasonable results.

Effective Thermal Conductivity of Functionally Graded Particulate Nanocomposites With Interfacial Thermal Resistance

2008 ◽  
Vol 75 (5) ◽  
Author(s):  
H. M. Yin ◽  
G. H. Paulino ◽  
W. G. Buttlar ◽  
L. Z. Sun
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Functionally Graded ◽  
Interfacial Thermal Resistance ◽  
Conductivity Distribution ◽  
Consistent Model ◽  
The Matrix ◽  
Graded Material ◽  
Perfect Interface

By means of a fundamental solution for a single inhomogeneity embedded in a functionally graded material matrix, a self-consistent model is proposed to investigate the effective thermal conductivity distribution in a functionally graded particulate nanocomposite. The “Kapitza thermal resistance” along the interface between a particle and the matrix is simulated with a perfect interface but a lower thermal conductivity of the particle. The results indicate that the effective thermal conductivity distribution greatly depends on Kapitza thermal resistance, particle size, and degree of material gradient.

scholarly journals The Influence of Burial Depth and Soil Thermal Conductivity on Heat Transfer in Buried CO2 Pipelines for CCS: A Parametric Study

2020 ◽  
Author(s):  
Babafemi Olugunwa ◽  
Julia Race ◽  
Tahsin Tezdogan
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Steady State ◽  
Thermal Resistance ◽  
Parametric Study ◽  
Flow Assurance ◽  
Burial Depth ◽  
Soil Thermal Conductivity ◽  
Dense Phase ◽  
Pipeline Transportation

Abstract Pipeline heat transfer modelling of buried pipelines is integral to the design and operation of onshore pipelines to aid the reduction of flow assurance challenges such as carbon dioxide (CO2) gas hydrate formation during pipeline transportation of dense phase CO2 in carbon capture and storage (CCS) applications. In CO2 pipelines for CCS, there are still challenges and gaps in knowledge in the pipeline transportation of supercritical CO2 due to its unique thermophysical properties as a single, dense phase liquid above its critical point. Although the design and operation of pipelines for bulk fluid transport is well established, the design stage is incomplete without the heat transfer calculations as part of the steady state hydraulic and flow assurance design stages. This paper investigates the steady state heat transfer in a buried onshore dense phase CO2 pipelines analytically using the conduction shape factor and thermal resistance method to evaluate for the heat loss from an uninsulated pipeline. A parametric study that critically analyses the effect of variation in pipeline burial depth and soil thermal conductivity on the heat transfer rate, soil thermal resistance and the overall heat transfer coefficient (OHTC) is investigated. This is done using a one-dimensional heat conduction model at constant temperature of the dense phase CO2 fluid. The results presented show that the influence of soil thermal conductivity and pipeline burial depth on the rate of heat transfer, soil thermal resistance and OHTC is dependent on the average constant ambient temperature in buried dense phase CO2 onshore pipelines. Modelling results show that there are significant effects of the ambient natural convection on the soil temperature distribution which creates a thermal influence region in the soil along the pipeline that cannot be ignored in the steady state modelling and as such should be modelled as a conjugate heat transfer problem during pipeline design.

scholarly journals Effective thermal conductivity of complicated hierarchic multilayer fabric

2014 ◽  
Vol 18 (5) ◽  
pp. 1613-1618 ◽  
Author(s):  
Jie Fan ◽  
Na Zhu ◽  
Zhi Liu ◽  
Qian Cheng ◽  
Yong Liu
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Geometric Feature ◽  
Retention Efficiency

Warm retention property of fabric is one of the most important factors for clothing comfortability. The worm retention efficiency of a multilayer fabric with hierarchic inner structure was investigated based on its geometric feature. The thermal resistance of the multilayer fabric increases as the layer of the fabric increases.

scholarly journals Sensitivity Enhancement of Silicon-on-Insulator CMOS MEMS Thermal Hot-Film Flow Sensors by Minimizing Membrane Conductive Heat Losses

Sensors ◽  
2019 ◽  
Vol 19 (8) ◽  
pp. 1860 ◽  
Author(s):  
Zahid Mehmood ◽  
Ibraheem Haneef ◽  
Syed Zeeshan Ali ◽  
Florin Udrea
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Film Flow ◽  
Heat Losses ◽  
Silicon On Insulator ◽  
Conductive Heat ◽  
Circular Membrane ◽  
Flow Sensors ◽  
Cmos Mems ◽  
Hot Film

Minimizing conductive heat losses in Micro-Electro-Mechanical-Systems (MEMS) thermal (hot-film) flow sensors is the key to minimize the sensors’ power consumption and maximize their sensitivity. Through a comprehensive review of literature on MEMS thermal (calorimetric, time of flight, hot-film/hot-film) flow sensors published during the last two decades, we establish that for curtailing conductive heat losses in the sensors, researchers have either used low thermal conductivity substrate materials or, as a more effective solution, created low thermal conductivity membranes under the heaters/hot-films. However, no systematic experimental study exists that investigates the effect of membrane shape, membrane size, heater/hot-film length and M e m b r a n e (size) to H e a t e r (hot-film length) Ratio (MHR) on sensors’ conductive heat losses. Therefore, in this paper we have provided experimental evidence of dependence of conductive heat losses in membrane based MEMS hot-film flow sensors on MHR by using eight MEMS hot-film flow sensors, fabricated in a 1 µm silicon-on-insulator (SOI) CMOS foundry, that are thermally isolated by square and circular membranes. Experimental results demonstrate that: (a) thermal resistance of both square and circular membrane hot-film sensors increases with increasing MHR, and (b) conduction losses in square membrane based hot-film flow sensors are lower than the sensors having circular membrane. The difference (or gain) in thermal resistance of square membrane hot-film flow sensors viz-a-viz the sensors on circular membrane, however, decreases with increasing MHR. At MHR = 2, this difference is 5.2%, which reduces to 3.0% and 2.6% at MHR = 3 and MHR = 4, respectively. The study establishes that for membrane based SOI CMOS MEMS hot-film sensors, the optimum MHR is 3.35 for square membranes and 3.30 for circular membranes, beyond which the gain in sensors’ thermal efficiency (thermal resistance) is not economical due to the associated sharp increase in the sensors’ (membrane) size, which makes sensors more expensive as well as fragile. This paper hence, provides a key guideline to MEMS researchers for designing the square and circular membranes-supported micro-machined thermal (hot-film) flow sensors that are thermally most-efficient, mechanically robust and economically viable.

Effective Thermal Conductivity of Submicron Powders: A Numerical Study

2016 ◽  
Vol 846 ◽  
pp. 500-505
Author(s):  
Wei Jing Dai ◽  
Yi Xiang Gan ◽  
Dorian Hanaor
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Granular Materials ◽  
Gas Phase ◽  
Numerical Study ◽  
Transfer Model ◽  
Size Of Particles ◽  
Contact Unit

Effective thermal conductivity is an important property of granular materials in engineering applications and industrial processes, including the blending and mixing of powders, sintering of ceramics and refractory metals, and electrochemical interactions in fuel cells and Li-ion batteries. The thermo-mechanical properties of granular materials with macroscopic particle sizes (above 1 mm) have been investigated experimentally and theoretically, but knowledge remains limited for materials consisting of micro/nanosized grains. In this work we study the effective thermal conductivity of micro/nanopowders under varying conditions of mechanical stress and gas pressure via the discrete thermal resistance method. In this proposed method, a unit cell of contact structure is regarded as one thermal resistor. Thermal transport between two contacting particles and through the gas phase (including conduction in the gas phase and heat transfer of solid-gas interfaces) are the main mechanisms. Due to the small size of particles, the gas phase is limited to a small volume and a simplified gas heat transfer model is applied considering the Knudsen number. During loading, changes in the gas volume and the contact area between particles are simulated by the finite element method. The thermal resistance of one contact unit is calculated through the combination of the heat transfer mechanisms. A simplified relationship between effective thermal conductivity and loading pressure can be obtained by integrating the contact units of the compacted powders.

Effective Thermal Conductivity of Composites with Contact Thermal Resistance between the Inclusions and the Matrix

2020 ◽  
Vol 40 (8) ◽  
pp. 622-627
Author(s):  
I. V. Lavrov ◽  
A. A. Kochetygov ◽  
V. V. Bardushkin ◽  
A. P. Sychev ◽  
V. B. Yakovlev
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Contact Thermal Resistance ◽  
The Matrix

Study of Effective Thermal Conductivity of Glazed Hollow Bead Concrete

2016 ◽  
Vol 851 ◽  
pp. 823-828
Author(s):  
Bing Zhang ◽  
Zhong Qing Cheng
Keyword(s):  
Thermal Conductivity ◽  
Thermal Resistance ◽  
Effective Thermal Conductivity ◽  
Thermal Conductivity Coefficient ◽  
Interface Thermal Resistance

Based on analyzing the mechanism of thermal conductivity of glazed hollow bead concrete, this paper divides the channels of thermal conductivity in concrete, constructs the model of thermal conductivity coefficient based on the Theory of Minimum Thermal Resistance, and confirms the model by using the data of other related literatures and the data of our own experiment. The consequence indicates that this model can calculate the thermal conductivity coefficient under arid state exactly. In order to improve the accuracy of this model, we should take the shape of framework, the interface thermal resistance between concrete and framework into consideration

Sign in / Sign up

Export Citation Format

Share Document