Collapse of Oil Well Casing

1982 ◽  
Vol 104 (1) ◽  
pp. 36-41 ◽  
Author(s):  
N. C. Huang ◽  
P. D. Pattillo

This paper is concerned with the theoretical study of the collapse of oil well casing under various loading conditions. The analysis is based on a model of a cylindrical shell of infinite length subjected to an axial tension and an external pressure. It is found that when the thickness-radius ratio of the casing is sufficiently small, collapse of the casing may take place in a form of plastic buckling. Critical conditions for plastic buckling are derived based on the J2-incremental theory and the J2-deformation theory. Another type of collapse is caused by the realization of the ultimate strength of the material. Critical conditions in the second case of collapse are calculated based on a plane strain formulation associated with the J2-incremental theory. The theoretical results obtained in this paper correspond well with empirical formulas developed earlier by the API for the design of oil well casing.

1984 ◽  
Vol 106 (2) ◽  
pp. 160-165 ◽  
Author(s):  
N. C. Huang ◽  
P. D. Pattillo

This paper presents an analysis of the cross-sectional collapse of a cylinder of finite length loaded simultaneously by an axial tension (which may be zero) and external pressure. The calculation is based on Sanders’ nonlinear shell equations with plasticity introduced via the concept of effective stress from a uniaxial tension test. The finite cylinder is an appropriate model of oil well casing as it undergoes quality control testing in the steel mill where the edges of the cylinder are usually fixed in the case of nonzero axial load and free in the case of zero axial load. However, in field application, the length: diameter ratio of casing is such that the cylinder may be considered infinite. Guidelines contained herein permit prediction of the collapse resistance of field casing from the results of mill tests performed on short samples.


1985 ◽  
Vol 107 (1) ◽  
pp. 128-134 ◽  
Author(s):  
P. D. Pattillo ◽  
N. C. Huang

The nonlinear response and eventual collapse of an initially imperfect cross section of a cylinder of infinite length is analyzed. The cylinder is loaded by external pressure and axial load and is intended to model oil well casing in a service environment. Results from the analysis agree well with experimental data and provide an interesting alternative to current empirical/statistical methods for determining the minimum collapse resistance of casing for use in design calculations.


Author(s):  
J Blachut ◽  
G D Galletly ◽  
S James

Previous investigations have raised some doubts about the accuracy of flow theory predictions for a few plate and shell plastic buckling problems. The present series of buckling experiments on machined, mild steel, cylindrical shell models under non-proportional biaxial loading (axial tension plus external pressure) was designed to provide additional data for the evaluation of the J2 plasticity theories. Numerical calculations were carried out with the BOSOR 5 shell buckling program, using the J2 deformation and flow theories, and these were compared with the test results. Neither theory can be said to predict plastic buckling accurately. However, deformation theory predicted the bifurcation buckling loads reasonably well, whereas flow theory was often incorrect.


2011 ◽  
Vol 1 (32) ◽  
pp. 15
Author(s):  
Yang-Yih Chen ◽  
Meng-Syue Li ◽  
Hung-Chu Hsu ◽  
Ying-Pin Lin

In this paper, a new third-order Lagrangian asymptotic solution describing nonlinear water wave propagation on the surface of a uniform sloping bottom is presented. The model is formulated in the Lagrangian variables and we use a two-parameter perturbation method to develop a new mathematical derivation. The particle trajectories, wave pressure and Lagrangian velocity potential are obtained as a function of the nonlinear wave steepness  and the bottom slope  perturbed to third order. The analytical solution in Lagrangian form satisfies state of the normal pressure at the free surface. The condition of the conservation of mass flux is examined in detail for the first time. The two important properties in Lagrangian coordinates, Lagrangian wave frequency and Lagrangian mean level, are included in the third-order solution. The solution can also be used to estimate the mean return current for waves progressing over the sloping bottom. The Lagrangian solution untangle the description of the features of wave shoaling in the direction of wave propagation from deep to shallow water, as well as the process of successive deformation of a wave profile and water particle trajectories leading to wave breaking. The proposed model has proved to be capable of a better description of non-linear wave effects than the corresponding approximation of the same order derived by using the Eulerian description. The proposed solution has also been used to determine the wave shoaling process, and the comparisons between the experimental and theoretical results are presented in Fig.1a~1b. In addition, the basic wave-breaking criterion, namely the kinematical Stokes stability condition, has been investigated. The comparisons between the present theory, empirical formula of Goda (2004) and the experiments made by Iwagali et al.(1974), Deo et al.(2003) and Tsai et al.(2005) for the breaking index(Hb/L0) versus the relative water depth(d0/L0) under two different bottom slopes are depicted in Figs 2a~2b. It is found that the theoretical breaking index is well agreement with the experimental results for three bottom slopes. However,for steep slope of 1/3 shown in Fig 2b, the result of Goda‘s empirical formula gives a larger value in comparison with the experimental data and the present theory. Some of empirical formulas presented the breaking wave height in terms of deepwater wave condition, such as in Sunamura (1983) and in Rattanapitikon and Shibayama(2000). Base on the results depicted in Fig. 3a~3b, it showed that the theoretical results are in good agreement with the experimental data (Iwagali et al. 1974, Deo et al.2003 and Tsai et al. 2005) than the empirical formulas. The empirical formula of Sunamura (1983) always predicts an overestimation value.


1973 ◽  
Vol 8 (3) ◽  
pp. 168-175 ◽  
Author(s):  
J M H Andrews ◽  
E G Ellison

There is a scarcity of multiaxial fatigue data available to designers especially in the high-strain régime. This is due in part of the complexity of the test equipment involved. A servo-hydraulic experimental rig has been developed for the application of biaxial high-strain reversed cycles to thin-walled tubular specimens, i.e. under axial tension and compression and internal and external pressure. It is capable of testing over a wide range of strain ratios and is reasonably versatile in that other information pertaining to buckling, Poisson's ratio, and criteria for yielding can be obtained.


2014 ◽  
Vol 761 ◽  
pp. 105-122 ◽  
Author(s):  
A. Siviglia ◽  
M. Toffolon

AbstractWe study the occurrence of the multiple steady states that flows in a collapsible tube can develop under the effect of: (i) geometrical alterations (e.g. stenosis), (ii) variations of the mechanical properties of the tube wall, or (iii) variations of the external pressure acting on the conduit. Specifically, if the approaching flow is supercritical, two steady flow states are possible in a restricted region of the parameter space: one of these flow states is wholly supercritical while the other produces an elastic jump that is located upstream of the variation. In the latter case the flow undergoes a transition through critical conditions in the modified segment of the conduit. Both states being possible, the actual state is determined by the past history of the system, and the parameter values show a hysteretic behaviour when shifting from one state to the other. First we set up the problem in a theoretical framework assuming stationary conditions, and then we analyse the dynamics numerically in a one-dimensional framework. Theoretical considerations suggest that the existence of multiple states is associated with non-uniqueness of the steady-state solution, which is confirmed by numerical simulations of the fully unsteady problem.


1970 ◽  
Vol 92 (2) ◽  
pp. 269-274
Author(s):  
R. C. DeHart ◽  
L. F. Greimann

Penetrations, in the pressure-resistant structure of a submersible, disturb the stress condition in the shell and may cause a premature failure. In this paper, two types of finite-element solutions are used to predict the stress distribution near view port openings in spherical shells under external pressure. Results of experimental stress analyses are also given and compared to the theoretical results.


2011 ◽  
Vol 146 ◽  
pp. 27-38
Author(s):  
F. Taouche ◽  
Kamal Ait Tahar ◽  
Ne Hannachi

The specific objectives of this study are: verifying the applicability of the proposed method of reinforcement of the beams by oblique connecting rods confined by a metallic embedded grid material to improve the behavior of concrete from the point of view strength to shear force, and confronting the experimental results acquired with empirical formulas developed by other researches. In this study, experimental investigations were performed to evaluate performance characteristics such as flexural ductility, resistance to shear force and load capacity. The experimental and numerical studies in the present work represent a promising revelation regarding the effectiveness of the proposed reinforcement process by an oblique connecting rods confined by a embedded metallic grid material laid out in the zone of influence of the shear force tilted to 45°. The confrontation of the experimental and theoretical results shows a satisfactory agreement.


Sign in / Sign up

Export Citation Format

Share Document