Aerodynamic and Heat Transfer Measurements on a Transonic Nozzle Guide Vane

1989 ◽  
Vol 111 (1) ◽  
pp. 36-42 ◽  
Author(s):  
E. T. Wedlake ◽  
A. J. Brooks ◽  
S. P. Harasgama
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Work Capacity ◽  
Test Facility ◽  
Transfer Rates ◽  
Improved Design ◽  
Nozzle Guide ◽  
Annular Cascade

Experimental determination of heat transfer rates to gas turbine blading plays an important part in the improvement of both the validation of existing design methods and the development of improved design codes. This paper describes a series of tests on an annular cascade of nozzle guide vanes designed for a high-work-capacity single-stage transonic turbine. The tests were carried out in the Isentropic Light Piston Cascade at the Royal Aerospace Establishment, Pyestock, and a brief description of this new test facility is included. Measurements of local heat transfer rates and aerodynamic data around the blade surface and on the end walls are described.

Measurement and Calculation of End Wall Heat Transfer and Aerodynamics on a Nozzle Guide Vane in Annular Cascade

1990 ◽  
Author(s):  
N. W. Harvey ◽  
T. V. Jones
Keyword(s):  
Heat Transfer ◽  
Guide Vane ◽  
Three Dimensional ◽  
Surface Flow ◽  
Wall Heat Transfer ◽  
Transfer Rates ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
End Wall

Detailed measurements of surface static pressures and heat transfer rates on the aerofoil and hub end wall of an annular nozzle guide vane (in the absence of a downstream rotor) are presented. Heat transfer rates have been measured using thin film gauges in an annular cascade in the Pyestock Isentropic Light Piston Cascade. Test Mach numbers, Reynolds numbers and cascade geometry are fully representative of engine conditions. The results of 3-D calculations of surface Mach number and 2-D calculations of aerofoil heat transfer are presented and compared with the measurements. A new method of calculating end wall heat transfer using the axisymmetric analogue for three-dimensional boundary layers is described in detail. The method uses a 3-D Euler solver to calculate the inviscid surface streamlines along which heat transfer coefficients are calculated. The metric coefficient which describes the lateral convergence or divergence of the streamlines is used to include three-dimensional effects in the calculation. The calculated heat transfer rates compare well with the measured values. Reference is made to surface flow visualization in the interpretation of the results.

Heat Transfer and Aerodynamics of a High Rim Speed Turbine Nozzle Guide Vane Tested in the RAE Isentropic Light Piston Cascade (ILPC)

1990 ◽  
Author(s):  
S. P. Harasgama ◽  
E. T. Wedlake
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Mach Number ◽  
Guide Vane ◽  
Weak Shock ◽  
Test Facility ◽  
Computational Techniques ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes

Detailed heat transfer and aerodynamic measurements have been made on an annular cascade of highly loaded nozzle guide vanes. The tests were carried out in an Isentropic Light Piston test facility at engine representative Reynolds number, Mach number and gas-to-wall temperature ratio. The aerodynamics indicate that the vane has a weak shock at 65–70% axial chord (mid span) with a peak Mach number of 1.14. The influence of Reynolds number and Mach number on the Nusselt number distributions on the vane and endwall surfaces are shown to be significant. Computational techniques are used for the interpretation of test data.

Heat Transfer and Aerodynamics of a High Rim Speed Turbine Nozzle Guide Vane Tested in the RAE Isentropic Light Piston Cascade (ILPC)

1991 ◽  
Vol 113 (3) ◽  
pp. 384-391 ◽  
Author(s):  
S. P. Harasgama ◽  
E. T. Wedlake
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Mach Number ◽  
Guide Vane ◽  
Weak Shock ◽  
Test Facility ◽  
Computational Techniques ◽  
Nozzle Guide ◽  
Annular Cascade ◽  
Nozzle Guide Vanes

Detailed heat transfer and aerodynamic measurements have been made on an annular cascade of highly loaded nozzle guide vanes. The tests were carried out in an Isentropic Light Piston test facility at engine representative Reynolds number, Mach number, and gas-to-wall temperature ratio. The aerodynamics indicate that the vane has a weak shock at 65–70 percent axial chord (midspan) with a peak Mach number of 1.14. The influence of Reynolds number and Mach number on the Nusselt number distributions on the vane and endwall surfaces are shown to be significant. Computational techniques are used for the interpretation of test data.

AN EXPERIMENTAL AND NUMERICAL STUDY OF HEAT TRANSFER IN A SIMULATED COLLECTOR FOR A SOLAR DRYER

1993 ◽  
Vol 17 (2) ◽  
pp. 145-160
Author(s):  
P.H. Oosthuizen ◽  
A. Sheriff
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Lower Surface ◽  
Local Heat ◽  
Electrical Heating ◽  
Temperature Profiles ◽  
Measured Temperature ◽  
Transfer Rates ◽  
Thermocouple Probe

Indirect passive solar crop dryers have the potential to considerably reduce the losses that presently occur during drying of some crops in many parts of the “developing” world. The performance so far achieved with such dryers has, however, not proved to be very satisfactory. If this performance is to be improved it is necessary to have an accurate computer model of such dryers to assist in their design. An important element is any dryer model is an accurate equation for the convective heat transfer in the collector. To assist in the development of such an equation, an experimental and numerical study of the collector heat transfer has been undertaken. In the experimental study, the collector was simulated by a 1m long by 1m wide channel with a gap of 4 cm between the upper and lower surfaces. The lower surface of the channel consisted of an aluminium plate with an electrical heating element, simulating the solar heating, bonded to its lower surface. Air was blown through this channel at a measured rate and the temperature profiles at various points along the channel were measured using a shielded thermocouple probe. Local heat transfer rates were then determined from these measured temperature profiles. In the numerical study, the parabolic forms of the governing equations were solved by a forward-marching finite difference procedure.

Heat Transfer in Separated, Reattached, and Redevelopment Regions Behind a Double Step at Entrance to a Flat Duct

1967 ◽  
Vol 89 (2) ◽  
pp. 163-167 ◽  
Author(s):  
E. G. Filetti ◽  
W. M. Kays
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Duct Flow ◽  
Double Step ◽  
Maximum Heat ◽  
Transfer Rates ◽  
Maximum Heat Transfer ◽  
Flow Cross

Experimental data are presented for local heat transfer rates near the entrance to a flat duct in which there is an abrupt symmetrical enlargement in flow cross section. Two enlargement area ratios are considered, and Reynolds numbers, based on duct hydraulic diameter, varied from 70,000 to 205,000. It is found that such a flow is characterized by a long stall on one side and a short stall on the other. Maximum heat transfer occurs in both cases at the point of reattachment, followed by a decay toward the values for fully developed duct flow. Empirical equations are given for the Nusselt number at the reattachment point, correlated as functions of duct Reynolds number and enlargement ratio.

Three-Dimensional Natural Convection From Vertical Heated Plates With Adjoining Cool Surfaces

1992 ◽  
Vol 114 (1) ◽  
pp. 115-120 ◽  
Author(s):  
B. W. Webb ◽  
T. L. Bergman
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Control Volume ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Infrared Thermal Imaging ◽  
Transfer Rates ◽  
Thermal Boundary Conditions

Natural convection in an enclosure with a uniform heat flux on two vertical surfaces and constant temperature at the adjoining walls has been investigated both experimentally and theoretically. The thermal boundary conditions and enclosure geometry render the buoyancy-induced flow and heat transfer inherently three dimensional. The experimental measurements include temperature distributions of the isoflux walls obtained using an infrared thermal imaging technique, while the three-dimensional equations governing conservation of mass, momentum, and energy were solved using a control volume-based finite difference scheme. Measurements and predictions are in good agreement and the model predictions reveal strongly three-dimensional flow in the enclosure, as well as high local heat transfer rates at the edges of the isoflux wall. Predicted average heat transfer rates were correlated over a range of the relevant dimensionless parameters.

Measurement and Calculation of Nozzle Guide Vane End Wall Heat Transfer

1998 ◽  
Author(s):  
Neil W. Harvey ◽  
Martin G. Rose ◽  
John Coupland ◽  
Terry Jones
Keyword(s):  
Heat Transfer ◽  
Stokes Equations ◽  
Guide Vane ◽  
Correction Method ◽  
Navier Stokes ◽  
Design Data ◽  
Navier Stokes Equations ◽  
Wall Functions ◽  
Transfer Rates ◽  
Nozzle Guide

A 3-D steady viscous finite volume pressure correction method for the solution of the Reynolds averaged Navier-Stokes equations has been used to calculate the heat transfer rates on the end walls of a modern High Pressure Turbine first stage stator. Surface heat transfer rates have been calculated at three conditions and compared with measurements made on a model of the vane tested in annular cascade in the Isentropic Light Piston Facility at DERA, Pyestock. The NGV Mach numbers, Reynolds numbers and geometry are fully representative of engine conditions. Design condition data has previously been presented by Harvey and Jones (1990). Off-design data is presented here for the first time. In the areas of highest heat transfer the calculated heat transfer rates are shown to be within 20% of the measured values at all three conditions. Particular emphasis is placed on the use of wall functions in the calculations with which relatively coarse grids (of around 140,000 nodes) can be used to keep computational run times sufficiently low for engine design purposes.

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

Aero-Thermal Performance of a Winglet at Engine Representative Mach and Reynolds Numbers

2010 ◽  
Author(s):  
D. O. O’Dowd ◽  
Q. Zhang ◽  
L. He ◽  
M. L. G. Oldfield ◽  
P. M. Ligrani ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Shock Wave ◽  
Thermal Performance ◽  
High Speed ◽  
Local Heat Transfer ◽  
Wave Structure ◽  
Local Heat ◽  
Test Facility ◽  
Shock Wave Structure ◽  
Spatially Resolved

This paper presents an experimental and numerical investigation of the aero-thermal performance of an uncooled winglet tip, under transonic conditions. Spatially-resolved heat transfer data, including winglet tip surface and near tip side walls, are obtained using the transient infrared thermography technique within the Oxford High Speed Linear Cascade test facility. CFD predictions are also conducted using the Rolls-Royce HYDRA suite. Most of the spatial heat transfer variations on the tip surface are well-captured by the CFD solver. The transonic flow pattern and its influence on heat transfer are analyzed, which shows that the turbine blade tip heat transfer is greatly influenced by the shock wave structure inside the tip gap. The effect of the casing relative motion is also numerically investigated. The CFD results indicate that the local heat transfer distribution on the tip is affected by the relative casing motion, but the tip flow choking and shock wave structure within the tip gap still exist in the aft region of the blade.

Sign in / Sign up

Export Citation Format

Share Document