The Effects of Fluid Inertia Forces on the Static Characteristics of Sector-Shaped, High-Speed Thrust Bearings in Turbulent Flow Regime

1989 ◽  
Vol 111 (3) ◽  
pp. 406-412 ◽  
Author(s):  
H. Hashimoto
Keyword(s):  
Carrying Capacity ◽  
High Speed ◽  
Experimental Results ◽  
Polar Coordinates ◽  
Load Carrying Capacity ◽  
Static Characteristics ◽  
Fluid Inertia ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Inertia Forces

This paper describes a study on the performance characteristics of sector-shaped, high-speed thrust bearings subjected to the effects of both turbulence and fluid inertia forces. The basic lubrication equations are derived by integrating the momentum and continuity equations in the polar coordinates including the full inertia terms throughout the film thickness; and a numerical calculation technique combining the control volume integration and the Newton-Raphson linearization method is applied to solve the equations. The static characteristics such as the load carrying capacity and the pressure center are calculated for various values of pad extent angle and inner-to-outer radius ratio of a pad. The theoretical results of the load carrying capacity are compared with the experimental results. It was found that the fluid inertia forces have significant effects on the static characteristics of the bearings. Good agreement was obtained between theoretical and experimental results.

Theoretical Investigation of Couple Stress Squeeze Films in a Curved Circular Geometry

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Vimala Manivasakan ◽  
Govindarajan Sumathi
Keyword(s):  
Theoretical Investigation ◽  
Carrying Capacity ◽  
Couple Stress ◽  
Squeeze Flow ◽  
Squeeze Film ◽  
Load Carrying Capacity ◽  
Fluid Inertia ◽  
Load Carrying ◽  
Inertia Forces ◽  
Good Agreement

A theoretical investigation of the laminar squeeze flow of a couple-stress fluid between a flat circular static disk and an axisymmetric curved circular moving disk has been carried out using modified lubrication theory and microcontinuum theory. The combined effects of fluid inertia forces, curvature of the disk and non-Newtonian couple stresses on the squeeze film behavior are investigated analytically. Each of these effects and their combinations show a significant enhancement in the squeeze film behavior, and these are studied through their effects on the squeeze film pressure and the load carrying capacity of the fluid film as a function of time. Two different forms of the gapwidth between the disks have been considered, and the results have been shown to be in good agreement with the existing literature.

Thermal and Inertia Effects in Turulent-Flow Thrust Bearings

1980 ◽  
Vol 22 (1) ◽  
pp. 43-45 ◽  
Author(s):  
Z. S. Safar
Keyword(s):  
Carrying Capacity ◽  
Thermal Effects ◽  
Analytical Study ◽  
Load Carrying Capacity ◽  
Inertia Effects ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Laminar And Turbulent Flow ◽  
Energy Equations ◽  
Inertia Forces

This paper presents a semi-analytical study of the influence of inertia terms on the thermohydrodynamic analysis of infinitely-wide thrust bearings operating under conditions of laminar and turbulent flow. The momentum and energy equations are not seriously affected by the presence of inertia forces. Results show that the inclusion of inertia terms causes an increase in the fluid film pressure and load-carrying capacity. Thermal effects exert a pronounced influence on bearing performance.

Performance Characteristic Analysis of Sector-Shaped Pad Thrust Bearings in Turbulent Inertial Flow Regime Under Three Types of Lubrication Conditions

1990 ◽  
Vol 112 (3) ◽  
pp. 477-484 ◽  
Author(s):  
H. Hashimoto
Keyword(s):  
Carrying Capacity ◽  
Control Volume ◽  
Linearization Method ◽  
Performance Characteristics ◽  
Experimental Results ◽  
Load Carrying Capacity ◽  
Characteristic Analysis ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Lubrication Conditions

An influence of lubrication conditions on the performance characteristics of sector-shaped pad thrust bearings, which are subjected to the effects of both turbulence and fluid film inertia, is investigated theoretically and experimentally. The momentum equations in terms of pressure and stream function are solved by applying a numerical calculation technique combining control volume integration and the Newton-Raphson linearization method, under three kinds of inlet boundary conditions in relation to three types of lubrication conditions, namely: the flooded condition, the over flooded condition, and the starved condition. Sample numerical results pertaining to the pressure distribution, load carrying capacity and inlet flow rate are obtained for θ = 60 deg, R1 = 0.5, Re = 2000, Re* = 0 to 1.6 and A = 1.0 to 2.0, and the results of the load-carrying capacity are compared with experimental results. From the theoretical and experimental results, the relationships between the lubrication conditions and the static performance characteristics of the bearings are clarified.

Computational Fluid Dynamics Thermohydrodynamic Analysis of Three-Dimensional Sector-Pad Thrust Bearings With Rectangular Dimples

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
C. I. Papadopoulos ◽  
L. Kaiktsis ◽  
M. Fillon
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Carrying Capacity ◽  
Thermal Effects ◽  
Operating Conditions ◽  
Load Carrying Capacity ◽  
Performance Indices ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Texture Design

The paper presents a detailed computational study of flow patterns and performance indices in a dimpled parallel thrust bearing. The bearing consists of eight pads; the stator surface of each pad is partially textured with rectangular dimples, aiming at maximizing the load carrying capacity. The bearing tribological performance is characterized by means of computational fluid dynamics (CFD) simulations, based on the numerical solution of the Navier–Stokes and energy equations for incompressible flow. Realistic boundary conditions are implemented. The effects of operating conditions and texture design are studied for the case of isothermal flow. First, for a reference texture pattern, the effects of varying operating conditions, in particular minimum film thickness (thrust load), rotational speed and feeding oil pressure are investigated. Next, the effects of varying texture geometry characteristics, in particular texture zone circumferential/radial extent, dimple depth, and texture density on the bearing performance indices (load carrying capacity, friction torque, and friction coefficient) are studied, for a representative operating point. For the reference texture design, the effects of varying operating conditions are further investigated, by also taking into account thermal effects. In particular, adiabatic conditions and conjugate heat transfer at the bearing pad are considered. The results of the present study indicate that parallel thrust bearings textured by proper rectangular dimples are characterized by substantial load carrying capacity levels. Thermal effects may significantly reduce load capacity, especially in the range of high speeds and high loads. Based on the present results, favorable texture designs can be assessed.

EXPERIMENTAL INVESTIGATION OF CFRP STRENGTHENED I-SHAPED COLD FORMED STEEL BEAMS

2017 ◽  
Vol 79 (5) ◽  
Author(s):  
Nahushananda Chakravarthy ◽  
Sivakumar Naganathan ◽  
Jonathan Tan Hsien Aun ◽  
Sreedhar Kalavagunta ◽  
Kamal Nasharuddin Mustapha ◽  
...  
Keyword(s):  
Carrying Capacity ◽  
Experimental Results ◽  
Steel Beams ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Length Width ◽  
Cold Formed Steel ◽  
Formed Channel ◽  
Hot Rolled ◽  
Hot Rolled Steel

Cold formed steel differ from hot rolled steel by its lesser thickness and weight. The cold formed steel applicable in roof purlin, pipe racks and wall panels etc. Due its lesser wall thickness the cold formed steel member subjected to buckling. The enhancement of load carrying capacity of the cold formed steel member can be achieved by external strengthening of CFRP. In this study cold formed channel members connected back to back to form I shaped cross section using screws. These built up beam members were 300mm, 400mm and 500mm in length with 100mm screw spacing and edge distance of 50mm were chosen for testing. CFRP fabric cut according to length, width of built up beams and wrapped outer surface of beam using epoxy resin. Experiments were carried out in two sets firstly plain built up beams and secondly CFRP wrapped beams. The test results shows that increased load carrying capacity and reduction in deflection due to CFRP strengthening. Experimental results were compared with AISI standards which are in good agreement. Experimental results shows that CFRP strengthening is economic and reliable.

Density Variation Effects in Stepped-Thrust Bearings

1959 ◽  
Vol 26 (3) ◽  
pp. 337-340
Author(s):  
C. F. Kettleborough
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Density Variation ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
The Coefficient Of Friction

Abstract The problem of the stepped-thrust bearing is considered but, whereas normally volumetric continuity is assumed, the equations are solved assuming mass continuity; i.e., the variation of density is also considered as well as the effect of the stepped discontinuity on the load-carrying capacity and the coefficient of friction. Computed theoretical curves illustrate the importance of the density on the operation of this bearing and, in part, explain results already published.

The Granular Lubricated Journal Bearing: Evidence of Lift Formation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Venkata K. Jasti ◽  
Martin C. Marinack ◽  
Deepak Patil ◽  
C. Fred Higgs
Keyword(s):  
Carrying Capacity ◽  
Granular Flow ◽  
High Speed ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Flow Behavior ◽  
Extreme Environments ◽  
Granular Flows ◽  
Load Carrying Capacity ◽  
Load Carrying

This work demonstrates that granular flows (i.e., macroscale, noncohesive spheres) entrained into an eccentrically converging gap can indeed actually exhibit lubrication behavior as prior models postulated. The physics of hydrodynamic lubrication is quite well understood and liquid lubricants perform well for conventional applications. Unfortunately, in certain cases such as high-speed and high-temperature environments, liquid lubricants break down making it impossible to establish a stable liquid film. Therefore, it has been previously proposed that granular media in sliding convergent interfaces can generate load carrying capacity, and thus, granular flow lubrication. It is a possible alternative lubrication mechanism that researchers have been exploring for extreme environments, or wheel-regolith traction, or for elucidating the spreadability of additive manufacturing materials. While the load carrying capacity of granular flows has been previously demonstrated, this work attempts to more directly uncover the hydrodynamic-like granular flow behavior in an experimental journal bearing configuration. An enlarged granular lubricated journal bearing (GLJB) setup has been developed and demonstrated. The setup was made transparent in order to visualize and video capture the granular collision activity at high resolution. In addition, a computational image processing program has been developed to process the resulting images and to noninvasively track the “lift” generated by granular flow during the journal bearing operation. The results of the lift caused by granular flow as a function of journal rotation rate are presented as well.

Influence of geometric parameters on the bump foil bearing performance

2019 ◽  
Vol 234 (7) ◽  
pp. 1017-1026
Author(s):  
Sadanand Kulkarni ◽  
Soumendu Jana
Keyword(s):  
Carrying Capacity ◽  
High Speed ◽  
System Development ◽  
Load Capacity ◽  
Radial Clearance ◽  
Load Carrying Capacity ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Load Carrying ◽  
Lift Off

High-speed rotating system development has drawn considerable attention of the researchers, in the recent past. Foil bearings are one of the major contenders for such applications, particularly for high speed and low load rotating systems. In foil bearings, process fluid or air is used as the working medium and no additional lubricant is required. It is known from the published literature that the load capacity of foil bearings depend on the operating speed, viscosity of the medium, clearance, and stiffness of the foil apart from the geometric dimensions of the bearing. In case of foil bearing with given dimensions, clearance governs the magnitude of pressure developed, whereas stiffness dictates the change in radial clearance under the generated pressure. This article deals with the effect of stiffness, clearance, and its interaction on the bump foil bearings load-carrying capacity. For this study, four sets of foil bearings of the same geometry with two levels of stiffness and clearance values are fabricated. Experiments are carried out following two factor-two level factorial design approach under constant load and in each case, the lift-off speed is measured. The experimental output is analyzed using statistical techniques to evaluate the influence of parameters under consideration. The results indicate that clearance has the maximum influence on the lift-off speed/ load-carrying capacity, followed by interaction effect and stiffness. A regression model is developed based on the experimental values and model is validated using error analysis technique.

Investigation on the Post-Ultimate Strength Behaviour of Sandwich Plate

2014 ◽  
Author(s):  
Wei Wang ◽  
Weijun Xu ◽  
Xiongliang Yao ◽  
Nana Yang
Keyword(s):  
Ultimate Strength ◽  
Carrying Capacity ◽  
Failure Modes ◽  
Sandwich Plate ◽  
Experimental Results ◽  
Sandwich Plates ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Strength Behavior ◽  
Simulation Results

This paper focuses on the post-ultimate strength behavior of sandwich plates. With widely application of the laminate on the ship and offshore structures, the post-ultimate strength behavior is becoming more important for safety evaluation of structures. Since the post-ultimate strength behavior can reflect the collapse extent of sandwich plate when subjected to extreme loads. A sandwich plate was modeled by FEM, its load-displacement relationship was obtained and its collapse characteristics were analyzed. The load-displacement relationship indicates its post-ultimate strength behavior, which is shown as that the load carrying capacity has a rapidly reduction when the ultimate strength is exceeded, and that the failure modes of the sandwich plate are determined by the parameter of individual layer. The simulation results were validated against experimental results. Conclusions are drawn: the displacement of sandwich plate under axial compression increased slowly before reaching the ultimate strength, once the ultimate strength was exceeded, the loads exerted on the structures sharply decreased with slowly increased displacement until the plate cracked. The simulation results have a good agreement with the experimental results. The mainly failure modes of sandwich plates can be interpreted as delamination between skin & core and core compression fracture, which are typical failure modes in engineering. The stiffness of sandwich structures decreased due to the interlaminar cracking or skin fracture, further the load carrying capacity decreased, which is of significance for guiding the design of sandwich structures.

Static characteristics of misaligned multiple axial groove water-lubricated bearing in the turbulent regime

2016 ◽  
Vol 231 (3) ◽  
pp. 385-398 ◽  
Author(s):  
Ravindra Mallya ◽  
Satish B Shenoy ◽  
Raghuvir Pai
Keyword(s):  
Reynolds Number ◽  
Friction Coefficient ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Load Capacity ◽  
Turbulent Regime ◽  
Load Carrying Capacity ◽  
Static Characteristics ◽  
Load Carrying ◽  
Turbulence Effects

The static characteristics of misaligned three-axial water-lubricated journal bearing in the turbulent regime are analyzed for groove angles 36° and 18°. Ng and Pan’s turbulence model is applied to study the turbulence effects in the journal bearing. The static parameters such as load-carrying capacity, friction coefficient, and side leakage are found for different degree of misalignment (DM). The change in flow regime of the lubricant from laminar to turbulent and the increase in misalignment, improved the load capacity of the bearing. For lightly loaded bearings, the friction coefficient of the bearing increased with the increase in Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document