Fiber-Reinforced Sandwich Plates Under Static Loads—Proposals for Their Optimization

1986 ◽  
Vol 108 (2) ◽  
pp. 152-158 ◽  
Author(s):  
H. A. Eschenauer ◽  
W. Fuchs
Keyword(s):  
Optimal Design ◽  
Composite Structures ◽  
Design Method ◽  
Sandwich Plates ◽  
Structural Members ◽  
Optimization Strategy ◽  
Static Loads ◽  
Conflicting Objectives ◽  
Sequential Linearization ◽  
Optimal Stiffness

In order to satisfy the permanently increasing specification demands on machines and plants, the structural members and units of the constructions have to be designed in an “optimal” way. Nowadays more and more composite structures are attaining such new fields of application where one-component materials are not able to fulfill the higher demands. Typical examples are light constructions with optimal stiffness at various loadings. In this paper, a detailed investigation of the deformation behavior of a simply supported sandwich plate under static loads is carried out. Then, an optimal design method is formulated as a nonlinear multiobjective optimization problem by adopting the two conflicting objectives “minimal deformation” at “minimal weight,” including a set of constraints. The application of an optimization strategy is shown by means of a special preference function and sequential linearization as optimizer. Finally, some results of this procedure are discussed concerning the optimal design of sandwich plates.

Development of the design method for the optimal design of the Neutron Converter experimental plant

2020 ◽  
Author(s):  
Timur Smetani ◽  
Elizaveta Gureva ◽  
Vyacheslav Andreev ◽  
Natalya Tarasova ◽  
Nikolai Andree
Keyword(s):  
Optimal Design ◽  
Flux Density ◽  
Design Process ◽  
Design Method ◽  
Fast Neutrons ◽  
Experimental Plant ◽  
Plant Design ◽  
State Technical ◽  
Research Organizations ◽  
Neutron Converter

The article discusses methods for optimizing the design of the Neutron Converter research plant design with parameters that are most suitable for a particular consumer. 38 similar plant structures with different materials and sources were calculated, on the basis of which the most optimal options were found. As part of the interaction between OKBM Afrikantov JSC and the Nizhny Novgorod State Technical University named after R. E. Alekseev, the Neutron Converter research plant was designed and assembled. The universal neutron converter is a device for converting a stream of fast neutrons emitted by isotopic sources into a "standardized" value of flux density with known parameters in the volume of the central part of the product, which is the working part of the universal neutron converter. To supply neutron converters to other customer organizations (universities, research organizations and collective centers), it is necessary to take into account the experience of operating an existing facility, as well as rationalize the design process of each specific instance in accordance with the requirements of the customer.

scholarly journals Reducing the metabolic energy of walking and running using an unpowered hip exoskeleton

2021 ◽  
Vol 18 (1) ◽  
Author(s):  
Tiancheng Zhou ◽  
Caihua Xiong ◽  
Juanjuan Zhang ◽  
Di Hu ◽  
Wenbin Chen ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Design Method ◽  
Metabolic Cost ◽  
Metabolic Energy ◽  
Spring Stiffness ◽  
Spatiotemporal Parameters ◽  
The Common ◽  
Hip Flexion ◽  
Optimal Stiffness ◽  
Insight Into

Abstract Background Walking and running are the most common means of locomotion in human daily life. People have made advances in developing separate exoskeletons to reduce the metabolic rate of walking or running. However, the combined requirements of overcoming the fundamental biomechanical differences between the two gaits and minimizing the metabolic penalty of the exoskeleton mass make it challenging to develop an exoskeleton that can reduce the metabolic energy during both gaits. Here we show that the metabolic energy of both walking and running can be reduced by regulating the metabolic energy of hip flexion during the common energy consumption period of the two gaits using an unpowered hip exoskeleton. Methods We analyzed the metabolic rates, muscle activities and spatiotemporal parameters of 9 healthy subjects (mean ± s.t.d; 24.9 ± 3.7 years, 66.9 ± 8.7 kg, 1.76 ± 0.05 m) walking on a treadmill at a speed of 1.5 m s−1 and running at a speed of 2.5 m s−1 with different spring stiffnesses. After obtaining the optimal spring stiffness, we recruited the participants to walk and run with the assistance from a spring with optimal stiffness at different speeds to demonstrate the generality of the proposed approach. Results We found that the common optimal exoskeleton spring stiffness for walking and running was 83 Nm Rad−1, corresponding to 7.2% ± 1.2% (mean ± s.e.m, paired t-test p < 0.01) and 6.8% ± 1.0% (p < 0.01) metabolic reductions compared to walking and running without exoskeleton. The metabolic energy within the tested speed range can be reduced with the assistance except for low-speed walking (1.0 m s−1). Participants showed different changes in muscle activities with the assistance of the proposed exoskeleton. Conclusions This paper first demonstrates that the metabolic cost of walking and running can be reduced using an unpowered hip exoskeleton to regulate the metabolic energy of hip flexion. The design method based on analyzing the common energy consumption characteristics between gaits may inspire future exoskeletons that assist multiple gaits. The results of different changes in muscle activities provide new insight into human response to the same assistive principle for different gaits (walking and running).

scholarly journals Development of Optimal Design Method for Steel Double-Beam Floor System Considering Rotational Constraints

2021 ◽  
Vol 11 (7) ◽  
pp. 3266
Author(s):  
Insub Choi ◽  
Dongwon Kim ◽  
Junhee Kim
Keyword(s):  
Optimal Design ◽  
Design Process ◽  
Design Method ◽  
Steel Beams ◽  
High Gravity ◽  
Double Beam ◽  
Iterative Analysis ◽  
Floor Systems ◽  
Optimal Design Method ◽  
Floor System

Under high gravity loads, steel double-beam floor systems need to be reinforced by beam-end concrete panels to reduce the material quantity since rotational constraints from the concrete panel can decrease the moment demand by inducing a negative moment at the ends of the beams. However, the optimal design process for the material quantity of steel beams requires a time-consuming iterative analysis for the entire floor system while especially keeping in consideration the rotational constraints in composite connections between the concrete panel and steel beams. This study aimed to develop an optimal design method with the LM (Length-Moment) index for the steel double-beam floor system to minimize material quantity without the iterative design process. The LM index is an indicator that can select a minimum cross-section of the steel beams in consideration of the flexural strength by lateral-torsional buckling. To verify the proposed design method, the material quantities between the proposed and code-based design methods were compared at various gravity loads. The proposed design method successfully optimized the material quantity of the steel double-beam floor systems without the iterative analysis by simply choosing the LM index of the steel beams that can minimize objective function while satisfying the safety-related constraint conditions. In particular, under the high gravity loads, the proposed design method was superb at providing a quantity-optimized design option. Thus, the proposed optimal design method can be an alternative for designing the steel double-beam floor system.

scholarly journals A Two-Round Optimization Design Method for Aerostatic Spindles Considering the Fluid–Structure Interaction Effect

2021 ◽  
Vol 11 (7) ◽  
pp. 3017
Author(s):  
Qiang Gao ◽  
Siyu Gao ◽  
Lihua Lu ◽  
Min Zhu ◽  
Feihu Zhang
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Design Method ◽  
Fluid Structure Interaction ◽  
Design Procedure ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Aerostatic Spindle

The fluid–structure interaction (FSI) effect has a significant impact on the static and dynamic performance of aerostatic spindles, which should be fully considered when developing a new product. To enhance the overall performance of aerostatic spindles, a two-round optimization design method for aerostatic spindles considering the FSI effect is proposed in this article. An aerostatic spindle is optimized to elaborate the design procedure of the proposed method. In the first-round design, the geometrical parameters of the aerostatic bearing were optimized to improve its stiffness. Then, the key structural dimension of the aerostatic spindle is optimized in the second-round design to improve the natural frequency of the spindle. Finally, optimal design parameters are acquired and experimentally verified. This research guides the optimal design of aerostatic spindles considering the FSI effect.

A Displacement-Based Optimal Design Method of RC Frames Subjected to Minor Earthquakes

2012 ◽  
Vol 594-597 ◽  
pp. 795-799
Author(s):  
Gui Tao Chen ◽  
De Min Wei
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Virtual Work ◽  
Design Method ◽  
Horizontal Displacement ◽  
Target Displacement ◽  
Programming Technique ◽  
Direct Displacement Based Design ◽  
Rc Frames ◽  
Displacement Based

A displacement-based optimization design method of RC structure was proposed by combining direct displacement-based design method with nonlinear programming technique. To avert the influence of target displacement, the stationary constraint displacement was presented, and the target displacement can be updated during the optimal design process. Principle of virtual work and Gaussian integral method was employed to simplify the explicit relationship between horizontal displacement and the section dimension. Comparison analysis of the local optimal results corresponding to different displacement shapes was conducted to achieve global optimal design. The numerical tests presented demonstrate the computational advantages of the discussed methods and suggesting that the proposed method is a reliably and efficiently tool for displacement-based optimal design.

Development of High-Speed Response Electromagnetic Linear Actuator Using for Pneumatic Control Valve

2014 ◽  
Vol 532 ◽  
pp. 41-45 ◽  
Author(s):  
Myung Jin Chung
Keyword(s):  
Optimal Design ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Design Method ◽  
Control Valve ◽  
Design Parameters ◽  
Linear Actuator ◽  
Analytic Model ◽  
Electromagnetic Linear Actuator ◽  
Quadratic Programming Method

Analytic model of electromagnetic linear actuator in the function of electric and geometric parameters is proposed and the effects of the design parameters on the dynamic characteristics are analyzed. To improve the dynamic characteristics, optimal design is conducted by applying sequential quadratic programming method to the analytic model. This optimal design method aims to minimize the response time and maximize force efficiency. By this procedure, electromagnetic linear actuator having high-speed characteristics is developed.

Sign in / Sign up

Export Citation Format

Share Document