Ice Formation in a Pipe Containing Flows in the Transition and Turbulent Regimes

1981 ◽  
Vol 103 (2) ◽  
pp. 363-368 ◽  
Author(s):  
R. R. Gilpin
Keyword(s):  
Steady State ◽  
Pressure Drop ◽  
Band Structure ◽  
Entire Range ◽  
Reynolds Numbers ◽  
Ice Formation ◽  
Ice Growth

The form of the ice growth that occurs in a pipe containing flows which are initially in the transition and turbulent regimes was investigated. The ice-band structure reported previously [1] for Reynolds numbers near transition was observed to be of steady state ice structure formed in a pipe for flows with Reynolds numbers over the entire range of the present investigation (up to ReD = 1.4 × 104). Difference were, however, observed in the nature of the transient approach to this steady state ice structure. The influence of the ice-band structure on pressure drop and on pipe freeze-off were also investigated.

Pressure Drop in Mini-Scale Coiled Tubing

2013 ◽  
Author(s):  
M. Ghobadi ◽  
Y. S. Muzychka
Keyword(s):  
Steady State ◽  
Pressure Drop ◽  
Reynolds Numbers ◽  
Tube Length ◽  
Radius Of Curvature ◽  
Steady State Flow ◽  
Dean Number ◽  
Coiled Tubing ◽  
Wide Range ◽  
Simple Empirical Model

In the present study, laminar, steady state flow in mini-scale coiled tubes was studied experimentally. Three different tube diameters: 1.6 mm, 1.27 mm and 1.016 mm with different lengths of 1 m and 0.5 m were coiled with different radius of curvature to provide data over a wide range of Reynolds numbers from 5 to 2300. A simple empirical model is developed based on the experimental results to predict the pressure drop increase based on Dean number. The results and simple model are also compared to a well-known existing model for circular tubing. The coiled tube lengths used in this study were long enough to consider the flow to be fully developed. The effects of varying curvature and tube length are also studied. The pitch of the coils is restricted to the diameter of the tube to minimize the effect of coiling. Dean number is used instead of Coiled number (modified Dean number) which allows the results to be expanded to spiral and curved tubing.

scholarly journals Parametric optimization of a stamped longitudinal vortex generator inside a circular tube of a solar water heater at low Reynolds numbers

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
Felipe A. S. Silva ◽  
Luis Júnior ◽  
José Silva ◽  
Sandilya Kambampati ◽  
Leandro Salviano
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Reynolds Numbers ◽  
Geometric Parameters ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Solar Water Heater ◽  
Water Heater ◽  
Solar Water

AbstractSolar Water Heater (SWH) has low efficiency and the performance of this type of device needs to be improved to provide useful and ecological sources of energy. The passive techniques of augmentation heat transfer are an effective strategy to increase the convective heat transfer coefficient without external equipment. In this way, recent investigations have been done to study the potential applications of different inserts including wire coils, vortex generators, and twisted tapes for several solar thermal applications. However, few researchers have investigated inserts in SWH which is useful in many sectors where the working fluid operates at moderate temperatures. The longitudinal vortex generators (LVG) have been applied to promote heat transfer enhancement with a low/moderate pressure drop penalty. Therefore, the present work investigated optimal geometric parameters of LVG to enhance the heat transfer for a SWH at low Reynolds number and laminar flow, using a 3D periodical numerical simulation based on the Finite Volume Method coupled to the Genetic Algorithm optimization method (NSGA-II). The LVG was stamped over a flat plate inserted inside a smooth tube operating under a typical residential application corresponding to Reynolds numbers of 300, 600, and 900. The geometric parameters of LGV were submitted to the optimization procedure which can find traditional LVG such as rectangular-winglet and delta-winglet or a mix of them. The results showed that the application of LGVs to enhance heat transfer is an effective passive technique. The different optimal shapes of the LVG for all Reynolds numbers evaluated improved more than 50% of heat transfer. The highest augmentation heat transfer of 62% is found for the Reynolds number 900. However, the best thermo-hydraulic efficiency value is found for the Reynolds number of 600 in which the heat transfer intensification represents 55% of the pressure drop penalty.

scholarly journals The Influence of Different Types of Nanofluid on Thermal and Fluid Flow Performance of Liquid Cold Plate

2018 ◽  
Vol 7 (4.35) ◽  
pp. 148 ◽  
Author(s):  
Nur Irmawati Om ◽  
Rozli Zulkifli ◽  
P. Gunnasegaran
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Steady State ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Cold Plate ◽  
Governing Equations ◽  
Flow And Heat Transfer ◽  
Different Types ◽  
Volume Method

The influence of utilizing different nanofluids types on the liquid cold plate (LCP) is numerically investigated. The thermal and fluid flow performance of LCP is examined by using pure ethylene glycol (EG), Al2O3-EG and CuO-EG. The volume fraction of the nanoparticle for both nanofluid is 2%. The finite volume method (FVM) has been used to solved 3-D steady state, laminar flow and heat transfer governing equations. The presented results indicate that Al2O3-EG able to provide the lowest surface temperature of the heater block followed by CuO-EG and EG, respectively. It is also found that the pressure drop and friction factor are higher for Al2O3-EG and CuO-EG compared to the pure EG.

Numerical and Experimental Analysis of Turbulent Flow in Corrugated Pipes

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Henrique Stel ◽  
Rigoberto E. M. Morales ◽  
Admilson T. Franco ◽  
Silvio L. M. Junqueira ◽  
Raul H. Erthal ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Turbulent Flow ◽  
Friction Factor ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Velocity Magnitude ◽  
Geometric Configurations ◽  
Corrugated Surfaces ◽  
Friction Factors

This article describes a numerical and experimental investigation of turbulent flow in pipes with periodic “d-type” corrugations. Four geometric configurations of d-type corrugated surfaces with different groove heights and lengths are evaluated, and calculations for Reynolds numbers ranging from 5000 to 100,000 are performed. The numerical analysis is carried out using computational fluid dynamics, and two turbulence models are considered: the two-equation, low-Reynolds-number Chen–Kim k-ε turbulence model, for which several flow properties such as friction factor, Reynolds stress, and turbulence kinetic energy are computed, and the algebraic LVEL model, used only to compute the friction factors and a velocity magnitude profile for comparison. An experimental loop is designed to perform pressure-drop measurements of turbulent water flow in corrugated pipes for the different geometric configurations. Pressure-drop values are correlated with the friction factor to validate the numerical results. These show that, in general, the magnitudes of all the flow quantities analyzed increase near the corrugated wall and that this increase tends to be more significant for higher Reynolds numbers as well as for larger grooves. According to previous studies, these results may be related to enhanced momentum transfer between the groove and core flow as the Reynolds number and groove length increase. Numerical friction factors for both the Chen–Kim k-ε and LVEL turbulence models show good agreement with the experimental measurements.

Experimental Investigation of Effect of Tip Coolant Ejection on Internal Flow Characteristics Within a Realistic Blade Coolant Channel

2013 ◽  
Author(s):  
Jian Pu ◽  
Zhaoqing Ke ◽  
Jianhua Wang ◽  
Lei Wang ◽  
Hongde You
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Turbine Blade ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Flow Ratio ◽  
Lp Turbine ◽  
Mass Flow Ratio

This paper presents an experimental investigation on the characteristics of the fluid flow within an entire coolant channel of a low pressure (LP) turbine blade. The serpentine channel, which keeps realistic blade geometry, consists of three passes connected by a 180° sharp bend and a semi-round bend, 2 tip exits and 25 trailing edge exits. The mean velocity fields within several typical cross sections were captured using a particle image velocimetry (PIV) system. Pressure and flow rate at each exit were determined through the measurements of local static pressure and volume flow rate. To optimize the design of LP turbine blade coolant channels, the effect of tip ejection ratio (ER) from 180° sharp bend on the flow characteristics in the coolant channel were experimentally investigated at a series of inlet Reynolds numbers from 25,000 to 50,000. A complex flow pattern, which is different from the previous investigations conducted by a simplified square or rectangular two-pass U-channel, is exhibited from the PIV results. This experimental investigation indicated that: a) in the main flow direction, the regions of separation bubble and flow impingement increase in size with a decrease of the ER; b) the shape, intensity and position of the secondary vortices are changed by the ER; c) the mass flow ratio of each exit to inlet is not sensitive to the inlet Reynolds number; d) the increase of the ER reduces the mass flow ratio through each trailing edge exit to the extent of about 23–28% of the ER = 0 reference under the condition that the tip exit located at 180° bend is full open; e) the pressure drop through the entire coolant channel decreases with an increase in the ER and inlet Reynolds number, and a reduction about 35–40% of the non-dimensional pressure drop is observed at different inlet Reynolds numbers, under the condition that the tip exit located at 180° bend is full open.

Heat Transfer And Pressure Drop Of An Angled Discrete Turbulator At Elevated Reynolds Numbers Up To 900,000

2021 ◽  
pp. 1-29
Author(s):  
Sam Ghazi-Hesami ◽  
Dylan Wise ◽  
Keith Taylor ◽  
Peter Ireland ◽  
Étienne Robert
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Enhance Heat Transfer ◽  
Near Surface ◽  
Number Range ◽  
Smooth Channel

Abstract Turbulators are a promising avenue to enhance heat transfer in a wide variety of applications. An experimental and numerical investigation of heat transfer and pressure drop of a broken V (chevron) turbulator is presented at Reynolds numbers ranging from approximately 300,000 to 900,000 in a rectangular channel with an aspect ratio (width/height) of 1.29. The rib height is 3% of the channel hydraulic diameter while the rib spacing to rib height ratio is fixed at 10. Heat transfer measurements are performed on the flat surface between ribs using transient liquid crystal thermography. The experimental results reveal a significant increase of the heat transfer and friction factor of the ribbed surface compared to a smooth channel. Both parameters increase with Reynolds number, with a heat transfer enhancement ratio of up to 2.15 (relative to a smooth channel) and a friction factor ratio of up to 6.32 over the investigated Reynolds number range. Complementary CFD RANS (Reynolds-Averaged Navier-Stokes) simulations are performed with the κ-ω SST turbulence model in ANSYS Fluent® 17.1, and the numerical estimates are compared against the experimental data. The results reveal that the discrepancy between the experimentally measured area averaged Nusselt number and the numerical estimates increases from approximately 3% to 13% with increasing Reynolds number from 339,000 to 917,000. The numerical estimates indicate turbulators enhance heat transfer by interrupting the boundary layer as well as increasing near surface turbulent kinetic energy and mixing.

Heat Transfer and Pressure Drop in a Converging Pedestal Array With Exit Area Variation

2018 ◽  
Author(s):  
L. W. Soma ◽  
F. E. Ames ◽  
S. Acharya
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Flow Path ◽  
Internal Cooling ◽  
Channel Measurements ◽  
Trailing Edge ◽  
Cooling Air

The trailing edge of a vane is one of the most difficult areas to cool due to a narrowing flow path, high external heat transfer rates, and deteriorating external film cooling protection. Converging pedestal arrays are often used as a means to provide internal cooling in this region. The thermally induced stresses in the trailing edge region of these converging arrays have been known to cause failure in the pedestals of conventional solidity arrays. The present paper documents the heat transfer and pressure drop through two high solidity converging rounded diamond pedestal arrays. These arrays have a 45 percent pedestal solidity. One array which was tested has nine rows of pedestals with an exit area in the last row consistent with the convergence. The other array has eight rows with an expanded exit in the last row to enable a higher cooling air flow rate. The expanded exit of the eight row array allows a 30% increase in the coolant flow rate compared with the nine row array for the same pressure drop. Heat transfer levels correlate well based on local Reynolds numbers but fall slightly below non converging arrays. The pressure drop across the array naturally increases toward the trailing edge with the convergence of the flow passage. A portion of the cooling air pressure drop can be attributed to acceleration while a portion can be attributed to flow path losses. Detailed array static pressure measurements provide a means to develop a correlation for the prediction of pressure drop across the cooling channel. Measurements have been acquired over Reynolds numbers based on exit flow conditions and the characteristic pedestal length scale ranging from 5000 to over 70,000.

scholarly journals Experimental and Numerical Analysis of Additively Manufactured Inconel 718 Coupons With Lattice Structure

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Sarwesh Parbat ◽  
Zheng Min ◽  
Li Yang ◽  
Minking Chyu
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Pressure Drop ◽  
Inconel 718 ◽  
Lattice Structure ◽  
Unit Cell ◽  
Common Vertex ◽  
Constant Wall Temperature ◽  
Near Surface ◽  
Smooth Channel

Abstract In the present paper, two lattice geometries suitable for near surface and double wall cooling were developed and tested. The first type of unit cell consisted of six ligaments of 0.5 mm diameter joined at a common vertex near the middle. The second type of unit cell was derived from the first type by adding four mutually perpendicular ligaments in the middle plane. Two lattice configurations, referred to as L1 and L2, respectively, were obtained by repeating the corresponding unit cell in streamwise and spanwise directions in an inline fashion. Test coupons consisting of these lattice geometries embedded inside rectangular cooling channel with dimensions of 2.54 mm height, 38.07 mm width, and 38.1 mm in length were fabricated using Inconel 718 powder and selective laser sintering (SLS) process. The heat transfer and pressure drop performance was then evaluated using steady-state tests with constant wall temperature boundary condition and for channel Reynolds number ranging from 2800 to 15,000. The lattices depicted a higher heat transfer compared with a smooth channel and both the heat transfer and pressure drop increased with a decrease in the porosity from L1 to L2. Steady-state conjugate numerical results revealed formation of prominent vortical structures in the inter-unit cell spaces, which diverted the flow toward the top end wall and created an asymmetric heat transfer between the two end walls. In conclusion, these lattice structures provided an augmented heat transfer while favorably redistributing the coolant within channel.

Heat Transfer Enhancement in Electronic Modules Using Various Secondary Air Injection Hole Arrangements

1998 ◽  
Vol 120 (2) ◽  
pp. 342-347 ◽  
Author(s):  
B. A. Jubran ◽  
M. S. Al-Haroun
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Reynolds Numbers ◽  
Air Injection ◽  
Transfer Enhancement ◽  
Injection Hole ◽  
Secondary Air Injection ◽  
Secondary Air ◽  
Compound Angle

This paper reports an experimental investigation to study the effects of using various designs of secondary air injection hole arrangements on the heat transfer coefficient and the pressure drop characteristics of an array of rectangular modules at different values of free-stream Reynolds numbers in the range 8 × 103 to 2 × 104. The arrangement used is either one staggered row of simple holes or one row of compound injection holes. The pitch distances between the injection holes, as well as the injection angles, were varied in both the streamwise and spanwise directions. Generally, the presence of secondary air through the injection hole arrangement can give up to 54 percent heat transfer enhancement just downstream of the injection holes. The amount of heat transfer enhancement and pressure drop across the electronic modules is very much dependent on the design of the injection holes. The simple angle injection hole arrangement tends to give a better heat transfer enhancement and less pressure drop than the compound angle holes.

Sign in / Sign up

Export Citation Format

Share Document