Annulus Wall Boundary-Layer Measurements in a Four-Stage Compressor

1986 ◽  
Vol 108 (1) ◽  
pp. 2-6 ◽  
Author(s):  
N. A. Cumpsty
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Tip Clearance ◽  
The Other ◽  
Wall Boundary Layer ◽  
Multistage Compressors ◽  
Full Design

There are few available measurements of the boundary layers in multistage compressors when the repeating-stage condition is reached. These tests were performed in a small four-stage compressor; the flow was essentially incompressible and the Reynolds number based on blade chord was about 5 • 104. Two series of tests were performed; in one series the full design number of blades were installed, in the other series half the blades were removed to reduce the solidity and double the staggered spacing. Initially it was wished to examine the hypothesis proposed by Smith [1] that staggered spacing is a particularly important scaling parameter for boundary layer thickness; the results of these tests and those of Hunter and Cumpsty [2] tend to suggest that it is tip clearance which is most potent in determining boundary-layer integral thicknesses. The integral thicknesses agree quite well with those published by Smith.

A Review of Cascade Data on Secondary Losses in Turbines

1970 ◽  
Vol 12 (1) ◽  
pp. 48-59 ◽  
Author(s):  
J. Dunham
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Blade Loading ◽  
Axial Turbine ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Turbine Cascades

Theories and experiments on secondary losses in axial turbine cascades without end clearance are reviewed. A formula is given which correlates the effect of blade loading on secondary losses more successfully than hitherto. However, it is also shown that secondary losses increase with upstream wall boundary layer thickness. Only a tentative expression for that effect can be suggested. In order to predict secondary losses reliably more must be known about these wall boundary layers.

Characteristics of the Flow Past a Wall-Mounted Finite-Length Square Cylinder at Low Reynolds Number With Varying Boundary Layer Thickness

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Sachidananda Behera ◽  
Arun K. Saha
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flow Field ◽  
Layer Thickness ◽  
Finite Length ◽  
Boundary Layer Thickness ◽  
Square Cylinder ◽  
Near Wake ◽  
Wall Boundary Layer ◽  
Wall Boundary

Direct numerical simulation (DNS) is performed to investigate the modes of shedding of the wake of a wall-mounted finite-length square cylinder with an aspect ratio (AR) of 7 for six different boundary layer thicknesses (0.0–0.30) at a Reynolds number of 250. For all the cases of wall boundary layer considered in this study, two modes of shedding, namely, anti-symmetric and symmetric modes of shedding, were found to coexist in the cylinder wake with symmetric one occurring intermittently for smaller time duration. The phase-averaged flow field revealed that the symmetric modes of shedding occur only during instances when the near wake experiences the maximum strength of upwash/downwash flow. The boundary layer thickness seems to have a significant effect on the area of dominance of both downwash and upwash flow in instantaneous and time-averaged flow field. It is observed that the near-wake topology and the total drag force acting on the cylinder are significantly affected by the bottom-wall boundary layer thickness. The overall drag coefficient is found to decrease with thickening of the wall boundary layer thickness.

Modeling the 3-D Flow Effects on Deviation Angle for Axial Compressor Middle Stages

1986 ◽  
Vol 108 (1) ◽  
pp. 131-137 ◽  
Author(s):  
W. B. Roberts ◽  
G. K. Serovy ◽  
D. M. Sandercock
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Blade Element Theory ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Flow Effects ◽  
End Wall

A model of the spanwise variation of the 3-D flow effects on deviation is proposed for middle-stage rotors and stators. This variation is taken as the difference above or below that predicted by blade element theory at any spanwise location. It was found that the stator variation is strongly affected by the end-wall boundary-layer thickness as well as camber, solidity, and blade channel aspect ratio. Rotor variation was found to depend on end-wall boundary layer thickness and tip clearance normalized by blade span. If these parameters are known or can be calculated, the models provide a reasonable approximation to the spanwise variation of deviation for middle compressor stages operating at low to high subsonic inlet Mach numbers.

An example of steady laminar flow at large Reynolds number

1960 ◽  
Vol 9 (4) ◽  
pp. 593-602 ◽  
Author(s):  
Iam Proudman
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Boundary Layers ◽  
Tangential Velocity ◽  
Fluid Flows ◽  
The Other ◽  
Large Reynolds Number ◽  
Rotational Flows ◽  
Flow Domain ◽  
Source Of Information

The purpose of this note is to describe a particular class of steady fluid flows, for which the techniques of classical hydrodynamics and boundary-layer theory determine uniquely the asymptotic flow for large Reynolds number for each of a continuously varied set of boundary conditions. The flows involve viscous layers in the interior of the flow domain, as well as boundary layers, and the investigation is unusual in that the position and structure of all the viscous layers are determined uniquely. The note is intended to be an illustration of the principles that lead to this determination, not a source of information of practical value.The flows take place in a two-dimensional channel with porous walls through which fluid is uniformly injected or extracted. When fluid is extracted through both walls there are boundary layers on both walls and the flow outside these layers is irrotational. When fluid is extracted through one wall and injected through the other, there is a boundary layer only on the former wall and the inviscid rotational flow outside this layer satisfies the no-slip condition on the other wall. When fluid is injected through both walls there are no boundary layers, but there is a viscous layer in the interior of the channel, across which the second derivative of the tangential velocity is discontinous, and the position of this layer is determined by the requirement that the inviscid rotational flows on either side of it must satisfy the no-slip conditions on the walls.

Some Characteristics of the Vortical Motions in the Outer Region of Turbulent Boundary Layers (Data Bank Contribution)

1992 ◽  
Vol 114 (4) ◽  
pp. 530-536 ◽  
Author(s):  
J. C. Klewicki ◽  
R. E. Falco ◽  
J. F. Foss
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Outer Region ◽  
Signal Amplitude ◽  
Threshold Level ◽  
Data Bank ◽  
Turbulent Boundary Layers ◽  
Spanwise Vorticity

Time-resolved measurements of the spanwise vorticity component, ωz, are used to investigate the motions in the outer region of turbulent boundary layers. The measurements were taken in very thick zero pressure gradient boundary layers (Rθ = 1010, 2870, 4850) using a four wire probe. As a result of the large boundary layer thickness, at the outer region locations where the measurements were taken the wall-normal and spanwise dimensions of the probe ranged between 0.7 < Δy/η < 1.2 and 2.1 < Δz/η < 3.9, respectively, where η is the local Kolmogorov length. An analysis of vorticity based intermittency is presented near y/δ = 0.6 and 0.85 at each of the Reynolds numbers. The average intermittency is presented as a function of detector threshold level and position in the boundary layer. The spanwise vorticity signals were found to yield average intermittency values at least as large as previous intermittency studies using “surrogate” signals. The average intermittency results do not indicate a region of threshold independence. An analysis of ωz event durations conditioned on the signal amplitude was also performed. The results of this analysis indicate that for decreasing Rθ, regions of single-signed ωz increase in size relative to the boundary layer thickness, but decrease in size when normalized by inner variables.

scholarly journals On the identification of well-behaved turbulent boundary layers

2017 ◽  
Vol 822 ◽  
pp. 109-138 ◽  
Author(s):  
C. Sanmiguel Vila ◽  
R. Vinuesa ◽  
S. Discetti ◽  
A. Ianiro ◽  
P. Schlatter ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Velocity Profile ◽  
Skin Friction ◽  
Boundary Layers ◽  
Shape Factor ◽  
Outer Region ◽  
The Other ◽  
Diagnostic Plot ◽  
Other Hand

This paper introduces a new method based on the diagnostic plot (Alfredsson et al., Phys. Fluids, vol. 23, 2011, 041702) to assess the convergence towards a well-behaved zero-pressure-gradient (ZPG) turbulent boundary layer (TBL). The most popular and well-understood methods to assess the convergence towards a well-behaved state rely on empirical skin-friction curves (requiring accurate skin-friction measurements), shape-factor curves (requiring full velocity profile measurements with an accurate wall position determination) or wake-parameter curves (requiring both of the previous quantities). On the other hand, the proposed diagnostic-plot method only needs measurements of mean and fluctuating velocities in the outer region of the boundary layer at arbitrary wall-normal positions. To test the method, six tripping configurations, including optimal set-ups as well as both under- and overtripped cases, are used to quantify the convergence of ZPG TBLs towards well-behaved conditions in the Reynolds-number range covered by recent high-fidelity direct numerical simulation data up to a Reynolds number based on the momentum thickness and free-stream velocity $Re_{\unicode[STIX]{x1D703}}$ of approximately 4000 (corresponding to 2.5 m from the leading edge) in a wind-tunnel experiment. Additionally, recent high-Reynolds-number data sets have been employed to validate the method. The results show that weak tripping configurations lead to deviations in the mean flow and the velocity fluctuations within the logarithmic region with respect to optimally tripped boundary layers. On the other hand, a strong trip leads to a more energized outer region, manifested in the emergence of an outer peak in the velocity-fluctuation profile and in a more prominent wake region. While established criteria based on skin-friction and shape-factor correlations yield generally equivalent results with the diagnostic-plot method in terms of convergence towards a well-behaved state, the proposed method has the advantage of being a practical surrogate that is a more efficient tool when designing the set-up for TBL experiments, since it diagnoses the state of the boundary layer without the need to perform extensive velocity profile measurements.

scholarly journals Numerical investigations of flow around subsea covers at high Reynolds numbers

2021 ◽  
Vol 1201 (1) ◽  
pp. 012013
Author(s):  
G Yin ◽  
Y Zhang ◽  
M C Ong
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Numerical Simulations ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Stream Velocity ◽  
Layer Flow ◽  
High Reynolds

Abstract Two-dimensional (2D) numerical simulations of flow over wall-mounted rectangular and trapezoidal ribs subjected to a turbulent boundary layer flow with the normalized boundary layer thickness of δ/D = 0.73,1.96,2.52 (D is the height of the ribs) have been carried out by using the Reynolds-averaged Navier-Stokes (RANS) equations combined with the k – ω SST (Shear Stress Transport) turbulence model. The angles of the two side slopes of trapezoidal rib varies from 0° to 60°. The Reynolds number based on the free-stream velocity U ∞ and D are 1 × 106 and 2 × 106. The results obtained from the present numerical simulations are in good agreement with the published experimental data. Furthermore, the effects of the angle of the two side slopes of the trapezoidal ribs, the Reynolds number and the boundary layer thickness on the hydrodynamic quantities are discussed.

Wind-Tunnel Screens: Flow Instability and its Effect on Aerofoil Boundary Layers

1964 ◽  
Vol 68 (639) ◽  
pp. 198-198 ◽  
Author(s):  
P. Bradshaw
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Layer Thickness ◽  
Boundary Layers ◽  
Boundary Layer Thickness ◽  
Flow Instability ◽  
Flow Direction ◽  
Flat Plates ◽  
Mixing Processes ◽  
Flow Through

Morgan has described a spatial instability in the flow through screens or grids of small open-area ratio. Head and Rechenberg and others have observed large span-wise variations in the thickness and shear stress of nominally two-dimensional boundary layers on flat plates and aerofoils in wind tunnels. It now appears that these spanwise variations are caused by the instability of flow through the screens. The jets of air issuing from the pores of the screen attempt to entrain more air by the usual mixing processes, but can only entrain it from each other, so that groups of jets coalesce in rather random (steady) patterns determined by small irregularities in the weave. The resulting variations in axial velocity are virtually eliminated by the wind tunnel contraction, but variations in flow direction are not so greatly reduced: a theoretical analysis shows that the observed variations of boundary-layer thickness, which often reach ± 10 per cent of the mean, can be produced by directional variations in the working section of the order of ± 1/20 deg, with a spanwise wavelength of the same order as the boundary-layer thickness.

Sign in / Sign up

Export Citation Format

Share Document