Film Cooling From Two Rows of Holes Inclined in the Streamwise and Spanwise Directions

1985 ◽  
Vol 107 (1) ◽  
pp. 84-91 ◽  
Author(s):  
B. Jubran ◽  
A. Brown
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Free Stream ◽  
Pressure Gradients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Typical Range

This paper describes the results of an experimental investigation into the film cooling effectiveness of two rows of holes inclined in the stream and spanwise directions. The effects of hole and row spacings and combinations of inclinations are investigated in the presence of free-stream pressure gradients and turbulence for a typical range of blowing rates.

Influence of Two Rows Compound and Simple Angle Holes in Inline and/or Staggered on Film Cooling and Heat Transfer

2005 ◽  
Author(s):  
Bilal Y. Maiteh
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Film Cooling ◽  
Pressure Gradients ◽  
Heat Transfer Characteristics ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mainstream Flow ◽  
Favorable Pressure Gradient ◽  
Compound Angle

This paper describes the results of an experimental investigation into the effect of the mainstream flow history on the film cooling effectiveness and the heat transfer characteristics from the combination of one row of simple angle holes and one row of compound angle holes. The mainstream flow history includes: favorable pressure gradient factors in the range −1.11 × 10−6 to +1.11 × 10−6 and turbulence intensity in the range 0.3% to 4.7%. The presence of favorable pressure gradients in the flow reduces the film cooling protection of the surfaces from both compound angle holes or combination of simple and compound angle holes, while the presence of adverse pressure gradients increases the film cooling effectiveness at low blowing rate and decreases it at high blowing rate. Increasing the turbulence intensity reduces the film cooling effectiveness from compound angle holes or combination of simple and compound angle holes.

Experimental Investigation of the Effect of Purge Flow on Film Cooling Effectiveness on a Rotating Turbine With Non-Axisymmetric Endwall Contouring

2013 ◽  
Author(s):  
M. Rezasoltani ◽  
M. T. Schobeiri ◽  
J. C. Han
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Efficiency ◽  
Purge Flow ◽  
Endwall Contouring ◽  
And Performance ◽  
Cooling Loops ◽  
The Impact

The impact of the purge flow injection on aerodynamics and film cooling effectiveness of a three-stage high pressure turbine with non-axisymmetric endwall contouring has been experimentally investigated. As a continuation of the previously published work involving stator-rotor gap purge cooling, this study investigates film cooling effectiveness on the first stage rotor contoured platform due to a coolant gas injection. Film cooling effectiveness measurements are performed on the rotor blade platform using a pressure sensitive paint (PSP) technique. The present study examines, in particular, the film cooling effectiveness due to injection of coolant from the rotor cavity through the circumferential gap between the first stator followed by the first rotor. Efficiency and performance experiments were conducted with and without cooling injection to show (a) the impact of endwall contouring on the turbine efficiency and (b) the impact of film cooling injection in association with the endwall contouring. The experimental investigation is carried out in a three-stage turbine facility at the Turbomachinery Performance and Flow Research Laboratory (TPFL) at Texas A&M University. Its rotor includes non-axisymmetric endwall contouring on the first and second rotor row [1]. The turbine has two independent cooling loops. Film cooling effectiveness measurements are performed for three coolant-to-mainstream mass flow ratios of 0.5%, 1.0% and 1.5%. Film cooling data is also obtained for three rotational speeds, 3000 rpm (reference condition), 2550 rpm and 2400 rpm and compared with non-contoured endwall data.

Flow Dynamics and Film Cooling Effectiveness on a Non-Axisymmetric Contour Endwall in a Two-Dimensional Cascade Passage

2009 ◽  
Author(s):  
Gazi I. Mahmood ◽  
Ross Gustafson ◽  
Sumanta Acharya
Keyword(s):  
Temperature Field ◽  
Flow Field ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Behavior ◽  
Three Dimensional ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Blowing Ratio

The measured flow field and temperature field near a three-dimensional asymmetric contour endwall employed in a linear blade cascade are presented with and without film-cooling flow on the endwall. Flow field temperature and Nusselt number distributions along the asymmetric endwall with wall heating and no film-cooling flow are also reported to show local high heat transfer region on the endwall and justify the locations of the coolant holes. Adiabatic film-cooling effectiveness along the endwall is then measured to indicate the local effects of the coolant jets. The near endwall flow field and temperature field provide the coolant flow behavior and the interaction of coolant jets with the boundary layer flow. Thus, the local film-cooling effectiveness can be explained with the coolant jet trajectories. The measurements are obtained at the Reynolds number of 2.30×105 based on blade actual chord and inlet velocity, coolant-to-free stream temperature ratio of 0.93, and coolant-to-free stream density ratio of 1.06. The cascade employs the hub side blade section and passage geometry of the first stage rotor of GE-E3 turbine engine. The contour endwall profile is employed on the bottom endwall only in the cascade. The blowing ratio of the film-cooling flow varies from 1.0 to 2.4 from 71 discrete cylindrical holes located in the contour endwall. The three-dimensional profile of the endwall varies in height in both the pitchwise and axial directions. The flow field is quantified with the streamwise vorticity and turbulent intensity, pitchwise static pressure difference, flow yaw angle, and pitchwise velocity. Both the flow field and temperature data indicate that the coolant jets cover more distance in the pitchwise and axial direction in the passage as the blowing ratio increases. Thus, the local and average film-cooling effectiveness increase with the blowing ratio.

scholarly journals The Effect of Bulk Flow Pulsations on Film Cooling From Two Rows of Holes

1997 ◽  
Author(s):  
Dong Kee Sohn ◽  
Joon Sik Lee
Keyword(s):  
Boundary Layer ◽  
Film Cooling ◽  
Free Stream ◽  
Bulk Flow ◽  
Phase Lag ◽  
Cooling Effectiveness ◽  
Freestream Velocity ◽  
Film Cooling Effectiveness ◽  
Temperature Distributions ◽  
Flow Pulsations

Effect of bulk flow pulsations on film cooling from two rows of holes with inline and staggered arrangements is experimentally investigated. As a baseline study, a single row injection is also tested. Two-row injection is important because the phase lag between the two rows may cause changes in the film coolant coverage. Potential flow pulsations are generated by the rotating shutter mechanism attached downstream of the test section. Free-stream Strouhal number based on the boundary layer thickness is in the range of 0.033–0.33, and the amplitude of the phase-averaged freestream velocity due to static pressure variation about 10–20% Both the time-averaged and phase-averaged temperature distributions in the cross-sectional plane of the boundary layer are presented for four different pulsation frequencies of 0, 4, 20 and 40 Hz. Film cooling effectiveness is evaluated from the adiabatic wall temperature distributions, with time-averaged temperature measurements showing rapid diffusion of the injectant due to the free-stream pulsations. Effect of the phase lag between two rows is evidenced from the phase-averaged measurements, particularly in the case of staggered hole arrangement. All film cooling effectiveness distributions are reduced compared to no-pulsation case. Effect of pulsations appears dominantly in the case of the two-row staggered arrangement which shows more than 35% reduction in the film cooling effectiveness.

Evaluation of Two-Equation Models of Turbulence in Predicting Film Cooling Performance Under High Free Stream Turbulence

2007 ◽  
Author(s):  
Savas Yavuzkurt ◽  
Jawad S. Hassan
Keyword(s):  
Film Cooling ◽  
Free Stream ◽  
Turbulence Models ◽  
Accurate Solution ◽  
Diameter Ratio ◽  
Tube Length ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Density Ratios

The capabilities of four two-equation turbulence models in predicting film cooling effectiveness under high free stream turbulence (FST) intensity (Tu = 10%) were investigated and their performance are presented and discussed. The four turbulence models are: the standard k-ε, RNG, and realizable k-ε models as well as the standard k-ω model all four found in the FLUENT CFD code. In all models, the enhanced wall treatment has been used to resolve the flow near solid boundaries. A systematic approach has been followed in the computational setup to insure grid-independence and accurate solution that reflects the true capabilities of these models. Exact geometrical and flow-field replicas of an experimental study on discrete hole film cooling were generated and used in FLUENT. A pitch-to-diameter ratio of 3.04, injection tube length-to-diameter ratio of 4.6 and density ratios of 0.92 and 0.97 were some of the parameters used in the film cooling analysis. The study covered two levels of blowing ratios (M = 0.5 and 1.5) at an environment of what is defined as high initial free-stream turbulence intensity (Tu = 10%). Performance of these models under a very low initial FST were presented in a paper by the authors in Turbo Expo 2006. In that case, the standard k-ε model had the most consistent performance among all considered turbulence models and the best centerline film cooling effectiveness predictions under very low FST. However, after the addition of high FST in the free-stream, even the standard k-ε model started to deviate greatly from the experimental data (up to 200% over-prediction) under high blowing ratios (M = 1.5). The model which performed the best under high FST but low blowing ratios (M = 0.5) is still the standard k-ε model. In all cases only standard k-ε model results match the trends of data for both cases. It can be said that under high FST with high M all the models do not do a good job of predicting the data. It was concluded that these deviations resulted from the effects of both high FST and high M. Under high M, near the injection holes deviations could result from the limitations of Boussinesq hypothesis relating the direction of Reynolds stress to the mean strain rate. Also, it seems like all models have trouble including the effects of high FST by not being able to take into account high levels of diffusion of turbulence from the free stream. However, standard k-ε model still looks like the best candidate for further improvement with the addition of new diffusion model for TKE under high FST.

Film Cooling With Injection Through Holes: Adiabatic Wall Temperatures Downstream of a Circular Hole

1968 ◽  
Vol 90 (4) ◽  
pp. 384-393 ◽  
Author(s):  
R. J. Goldstein ◽  
E. R. G. Eckert ◽  
J. W. Ramsey
Keyword(s):  
Boundary Layer ◽  
Experimental Investigation ◽  
Turbulent Boundary Layer ◽  
Film Cooling ◽  
Main Flow ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Secondary Air ◽  
Secondary Fluid

An experimental investigation has been conducted to determine the film cooling effectiveness with injection of air through a discrete hole into a turbulent boundary layer of air on a flat plate. The secondary air enters at either an angle of 35 deg or an angle of 90 deg to the main flow. The film cooling effectiveness is found to be considerably different from that obtained in previous studies in which the secondary fluid was introduced through a continuous slot.

Double-Row Discrete-Hole Cooling: an Experimental and Numerical Study

1980 ◽  
Vol 102 (2) ◽  
pp. 498-503 ◽  
Author(s):  
G. Bergeles ◽  
A. D. Gosman ◽  
B. E. Launder
Keyword(s):  
Flow Field ◽  
Film Cooling ◽  
Free Stream ◽  
Numerical Study ◽  
Transport Coefficients ◽  
Three Dimensional ◽  
Double Row ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row

Double-row discrete-hole cooling arrangements offer several advantages over single-row systems yet the detailed cooling mechanism is less completely understood than for the single-row. This is partly because there have been fewer studies of this geometry and partly because the flow structure is more complex. The present paper presents detailed flow-field and concentration measurements around the injection holes for double-row injection on a flat plate at 30 deg to the mainstream. The experiments span values of the blowing injection mass velocities from 0.25 to 1.0 times the free stream mass velocity and for two boundary layer thicknesses just upstream of the injection. In contrast to single-row injection the cooling effectiveness rise monotonically with M over the range studied. Computer simulation of these flows and similar experiments of [7] has been made using a three-dimensional finite-difference code that embodies a semi-elliptic treatment of the flow field in the neighborhood of the injection holes in conjunction with a two-equation turbulence model with non-isotropic effective transport coefficients. It emerged from the calculations, that, for injection velocities up to 50 percent of the free stream value, levels of film-cooling effectiveness are extremely well predicted beyond about 10 diameters behind the leading row of holes. Around the holes themselves, however, there are certain discrepancies which become more serious as the injection level is raised.

Sign in / Sign up

Export Citation Format

Share Document