Repowering in Steel Works by Introducing a Blast-Furnace, Gas-Firing Gas Turbine

1984 ◽  
Vol 106 (4) ◽  
pp. 806-811 ◽  
Author(s):  
A. Muyama ◽  
H. Hiura ◽  
K. Morimoto
Keyword(s):  
Blast Furnace ◽  
Gas Turbine ◽  
Field Tests ◽  
Calorific Value ◽  
Efficiency Improvement ◽  
Plant Design ◽  
Blast Furnace Gas ◽  
Steam Plant ◽  
Plant Efficiency ◽  
Steel Works

A 14-MW, high-temperature gas turbine firing extremely low-BTU, blast-furnace gas was developed and installed in a steel works of Japan as a repowering unit. Field tests proved the stable combustion up to 590 Kcal/Nm3 calorific value and plant efficiency improvement of up to 60 percent on existing steam plant. Design features and two years operational experiences are presented.

Design for the 145-MW Blast Furnace Gas Firing Gas Turbine Combined Cycle Plant

1989 ◽  
Vol 111 (2) ◽  
pp. 218-224 ◽  
Author(s):  
H. Takano ◽  
Y. Kitauchi ◽  
H. Hiura
Keyword(s):  
Blast Furnace ◽  
Gas Turbine ◽  
Large Scale ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Mixed Gas ◽  
Fuel Gas ◽  
Blast Furnace Gas ◽  
Combined Cycle Plant ◽  
Steel Works

A 145-MW blast furnace gas firing gas turbine combined cycle plant was designed and installed in a steel works in Japan as a repowering unit. A 124-MW large-scale gas turbine with turbine inlet temperature 1150°C (1423 K) was adopted as a core engine for the combined cycle plant. The fuel of this gas turbine is blast furnace gas mixed with coke oven gas. These are byproducts of steel works, and the calorific value of the mixed gas is controlled to be about 1000 kcal/Nm3 (4187 kJ/Nm3). A specially designed multicannular type combustor was developed to burn such a low Btu fuel. The gas turbine, generator, steam turbine, and fuel gas compressor are connected to make a single-shaft configuration. As a result of introducing the gas turbine combined cycle plant, the plant thermal efficiency was above 45 percent (at NET) and the total electricity generation in the works has increased from 243 MW to 317 MW. This paper describes the design features of this combined cycle plant.

Atmospheric Tests of a Full Scale Gas Turbine Burner Fed With Blast Furnace Gas and Coke Oven Gas

2019 ◽  
Author(s):  
Edoardo Bertolotto ◽  
Alberto Amato ◽  
Li Guoqiang
Keyword(s):  
Blast Furnace ◽  
Natural Gas ◽  
Gas Turbine ◽  
Coke Oven ◽  
Full Scale ◽  
Flame Stability ◽  
Coke Oven Gas ◽  
Stability Range ◽  
Blast Furnace Gas ◽  
Inlet Conditions

Abstract The present paper describes atmospheric experimental tests of a new Ansaldo Energia full scale burner which was designed to burn fuels byproduct of steel making processes (mixtures of Blast-Furnace Gas (BFG) and Coke-Oven Gas (COG)), characterized by very low heating values (LHV∼2–3.5 MJ/kg) and very low stoichiometric air/fuel ratios (∼0.5–1 kg/kg). In particular, flame stability and blow-out margins were assessed for different burner variants and fuel compositions such as pure BFG, blends of BFG with increasing content of COG, and also a synthetic mixture of natural gas, hydrogen and nitrogen (NG/H2/N2). Except for pressure, all burner inlet conditions were simulated as in the actual gas turbine engine. The best performing burner among those tested demonstrated an excellent burning stability behavior over a wide operating range and stably burned pure BFG without any supplementary fuel. Furthermore, considering that in most operating concepts gas turbine engines for Ultra-Low BTU applications require a back-up fuel (such as oil, propane or natural gas) to ignite and ramp up or to perform load-rejections, the present atmospheric tests also assessed maneuvers to switch from natural gas operation to syngas operation. Also in this type of dual-fuel operation the burner demonstrated a wide flame stability range.

Determination of the Optimal Structure of Repowering a Metallurgical CHP Plant Fired with Technological Fuel Gases

2014 ◽  
Vol 59 (1) ◽  
pp. 105-116 ◽  
Author(s):  
A. Ziebik ◽  
M. Warzyc ◽  
P. Gładysz
Keyword(s):  
Blast Furnace ◽  
Gas Turbine ◽  
Input Data ◽  
Coke Oven ◽  
Combined Cycle ◽  
Chemical Energy ◽  
Optimal Structure ◽  
Hard Coal ◽  
Average Value ◽  
Blast Furnace Gas

Abstract CHP plants in ironworks are traditionally fired with low-calorific technological fuel gases and hard coal. Among metallurgical fuel gases blast-furnace gas (BFG) dominates. Minor shares of gaseous fuels are converter gas (LDG) and surpluses of coke-oven gas (COG). Metallurgical CHP plant repowering consists in adding a gas turbine to the existing traditional steam CHP plant. It has been assumed that the existing steam turbine and parts of double-fuel steam boilers can be used in modernized CHP plants. Such a system can be applied parallelly with the existing steam cycle, increasing the efficiency of utilizing the metallurgical fuel gases. The paper presents a method and the final results of analyzing the repowering of an existing metallurgical CHP plant fired with low-calorific technological fuel gases mixed with hard coal. The introduction of a gas turbine cycle results in a better effectiveness of the utilization of metallurgical fuel gases. Due to the probabilistic character of the input data (e.g. the duration curve of availability of the chemical energy of blast-furnace gas for CHP plant, the duration curve of ambient temperature) the Monte Carlo method has been applied in order to choose the optimal structure of the gas-and-steam combined cycle CHP unit, using the Gate Cycle software. In order to simplify the optimizing calculation, the described analysis has also been performed basing on the average value of availability of the chemical energy of blast-furnace gas. The fundamental values of optimization differ only slightly from the results of the probabilistic model. The results obtained by means of probabilistic and average input data have been compared using new information and a model applying average input data. The new software Thermoflex has been used. The comparison confirmed that in the choice of the power rating of the gas turbine based on both computer programs the results are similar.

Investigations of the Stabilities of Piloted Flames Using Blast Furnace Gas

2015 ◽  
Author(s):  
Chunyan Li ◽  
Haojie Tang ◽  
Liyue Jing ◽  
Min Zhu
Keyword(s):  
Blast Furnace ◽  
Low Cost ◽  
Diagnostic System ◽  
Calorific Value ◽  
Dynamic Responses ◽  
Low Grade ◽  
Blast Furnace Gas ◽  
Flame Dynamics ◽  
Main Burner ◽  
Set Up

The effective utilization of low-grade energy sources generated from steel-making processes provides not only excellent opportunities for low cost power generation but also a significant means for the reduction of greenhouse gas emissions. In this paper, the work was carried out to study the static and dynamic combustion instabilities for gas turbine combustors burning low-calorific-value blast furnace gas (BFG). A burner was designed to stabilize the BFG flame with central pilot flames. A diagnostic system was set up to detect the characteristics of flame dynamics. In the experiments, the fuel ratio between the pilot and main burner and, the equivalence ratio of the main flame and the annular flow velocity were varied for the investigation of the combustion lean blowout (LBO) limits. The flame dynamics near LBO were investigated. The dynamic responses of the flame to flow perturbations were also measured. A network model was employed to study and validate the blowout mechanisms. The LBO limits were calculated and compared with experimental results for various equivalence ratios.

Operating Experience of Ansaldo V94.2 K Gas Turbine Fed by Steelworks Gas

2002 ◽  
Author(s):  
Federico Bonzani ◽  
Giacomo Pollarolo ◽  
Franco Rocca
Keyword(s):  
Blast Furnace ◽  
Natural Gas ◽  
Gas Turbine ◽  
Operating Experience ◽  
Coke Oven ◽  
Operating Conditions ◽  
Total Power ◽  
Dual Fuel ◽  
Coke Oven Gas ◽  
Blast Furnace Gas

ANSALDO ENERGIA S.p.A. has been commissioned by ELETTRA GLT S.p.A, a company located in Trieste, Italy for the realisation of a combined cycle plant where all the main components (gas turbine, steam turbine, generator and heat recovery steam generator) are provided by ANSALDO ENERGIA. The total power output of the plant is 180 MW. The gas turbine is a V94.2 K model gas turbine dual fuel (natural gas and steelworks process gas), where the fuel used as main fuel is composed by a mixture of natural gas, blast furnace gas and coke oven gas in variable proportions according to the different working conditions of the steel work plant. The main features adopted to burn such a kind of variability of fuels are reported below: • fuel as by product of steel making factory gas (coke oven gas “COG”, blast furnace gas “BFG”) with natural gas integration; • modified compressor from standard V94.2, since no air extraction is foreseen; • dual fuel burner realised based on Siemens design. This paper describes the operating experience achieved on the gas turbine, focusing on the main critical aspect to be overcome and on to the test results during the commissioning and the early operating phase. The successful performances carried out have been showing a high flexibility in burning with stable combustion a very different fuel compositions with low emissions measured all operating conditions.

scholarly journals Measurements on a Blast-Furnace-Gas and Oil-Fired Combustion Chamber of a 17.25-MWe Closed-Cycle Gas Turbine Plant

1970 ◽  
Author(s):  
K. Bammert ◽  
H. Rehwinkel
Keyword(s):  
Blast Furnace ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Fuel Oil ◽  
Test Results ◽  
Closed Cycle ◽  
Combustion Chambers ◽  
Blast Furnace Gas ◽  
Stage Of Development

The paper discusses the present stage of development of combustion chambers for fossil-fired closed-cycle gas turbines, describing West Germany’s “Gelsenkirchen” plant which can be operated with blast-furnace gas and fuel oil with any desired ratio of gas to oil. The output data and the efficiency of this plant are illustrated by test results. In the development and construction of fossil-fired closed-cycle gas turbine plants, the gas heater presents the greatest difficulties and is the most expensive part of the plant. Therefore, very detailed measurements were taken to determine the total heat absorption in the combustion chamber and its local distribution over the length of the chamber. The results obtained are compared with previous measurements at a smaller plant, the mine-gas and pulverized-coal fired “Haus Aden” plant.

Three Years’ Operating Experience With 7500-kw Gas-Turbine Plants in Belgian Steelworks

1960 ◽  
Author(s):  
E. Aguet ◽  
J. von Salis
Keyword(s):  
Blast Furnace ◽  
Electric Power ◽  
Gas Turbine ◽  
Steel Industry ◽  
Gas Turbines ◽  
Operating Experience ◽  
Point Of View ◽  
Blast Furnace Gas ◽  
Commercial Operation

Gas turbines are being used in increasing numbers in the European steel industry, utilizing as fuel blast-furnace gas, and producing either electric power or blast-furnace wind; in some cases both combined. It is now possible to put on record results obtained with these machines in commercial operation, as some of the units have been running practically nonstop for several years. Apart from teething troubles during the first few thousand running hours, the gas turbine has fulfilled all expectations, both regarding the economics of operation and from the maintenance point of view.

Sign in / Sign up

Export Citation Format

Share Document