Heat Transfer Limitation of a Micro Heat Pipe

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
K. N. Shukla
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transport ◽  
Analytical Expression ◽  
Micro Heat Pipe ◽  
Capillary Limit ◽  
Heat Transport Capability

An analytical expression for the heat transport capability of micro heat pipe is derived. The vapor continuum limitation has been considered in deriving the heat transport capability of a micro heat pipe. As the micro heat pipe uses sharp-cornered square, triangular, or other polygonal channels that can serve as capillary arteries, its transport capability depends on the capillary limit. It has been shown that the operating limit of the micro heat pipe depends on the vapor continuum limitation, capillary limit, and the gravity.

Experimental Investigation of Ultrasonic Frequency Effect on an Oscillating Heat Pipe

2016 ◽  
Author(s):  
Nannan Zhao ◽  
Benwei Fu ◽  
Hongbin Ma ◽  
Fengmin Su
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transport ◽  
Frequency Effect ◽  
Ultrasonic Frequency ◽  
Sound Effect ◽  
Oscillating Heat Pipe ◽  
Ultrasonic Sound ◽  
Heat Transfer Capacity ◽  
Heat Transport Capability

The heat transport capability in an oscillating heat pipe (OHP) significantly depends on the oscillating frequency. An external frequency directly affects the natural frequency in the system. In this investigation, the ultrasound sound effect on the heat transport capability in an OHP was conducted with focus on the ultrasonic frequency effect on the oscillating motion and heat transfer capacity in an OHP. The ultrasonic sound was applied to the evaporating section of the OHP by using the electrically-controlled piezoelectric ceramics. The heat pipe was tested with or without the ultrasonic sound with different frequencies. In addition, the effects of operating temperature, heat load from 25 W to 150 W were investigated. The experimental results demonstrate that the heat transfer capacity enhancement of the OHP depends on the frequency of the ultrasound field, and there exists an optimum combination of the frequencies which will lead to the largest enhancement of the heat transfer capacity of the OHP.

A Mathematical Modeling Method for Capillary Limit of Micro Heat Pipe with Sintered Wick

2011 ◽  
Vol 175 ◽  
pp. 335-341
Author(s):  
Xi Bing Li ◽  
Chang Long Yang ◽  
Gong Di Xu ◽  
Wen Yuan ◽  
Shi Gang Wang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Heat Dissipation ◽  
High Heat ◽  
Experimental Investigations ◽  
High Heat Flux ◽  
Micro Heat Pipe ◽  
Copper Powders ◽  
Capillary Limit

With heat flux increasing and cooling space decreasing in microelectronic and chemical products, micro heat pipe has become an ideal heat dissipation device in high heat-flux products. Through the analysis of its working principle, the factors that affect its heat transfer limits and the patterns in which copper powders are arrayed in circular cavity, this paper first established a mathematical model for the crucial factors in affecting heat transfer limits in a circular micro heat pipe with a sintered wick, i.e. a theoretical model for capillary limit, and then verified its validity through experimental investigations. The study lays a powerful theoretical foundation for designing and manufacturing circular micro heat pipes with sintered wicks.

Temperature Response of Heat Transport in a Micro Heat Pipe

1999 ◽  
Vol 121 (2) ◽  
pp. 438-445 ◽  
Author(s):  
G. P. Peterson ◽  
H. B. Ma
Keyword(s):  
Thin Film ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transport ◽  
Capillary Flow ◽  
Temperature Drop ◽  
Temperature Response ◽  
Axial Direction ◽  
Vapor Flow ◽  
Micro Heat Pipe

A detailed mathematical model for predicting the heat transport capability and temperature gradients that contribute to the overall axial temperature drop as a function of heat transfer in a micro heat pipe has been developed. The model utilizes a third-order ordinary differential equation, which governs the fluid flow and heat transfer in the evaporating thin film region; an analytical solution for the two-dimension heat conduction equation, which governs the macro evaporating film region in the triangular corners; the effects of the vapor flow on the liquid flow in the micro heat pipe; the flow and condensation of the thin film caused by the surface tension in the condenser; and the capillary flow along the axial direction of the micro heat pipe. With this model, the temperature distribution along the axial direction of the heat pipe and the effect on the heat transfer can be predicted. In order to verify the model presented here, an experimental investigation was also conducted and a comparison with experimental data made. This comparison indicated excellent correlation between the analytical model and experimental results, and as a result, the analysis provides a better understanding of the heat transfer capability and temperature variations occurring in micro heat pipes.

An Experimental Investigation on Micro Heat Pipe with a Trapezium-Grooved Wick Structure

2010 ◽  
Vol 29-32 ◽  
pp. 1695-1700
Author(s):  
Shi Gang Wang ◽  
Xi Bing Li ◽  
Bai Rui Tao ◽  
Hong Xia Zhang
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
Optimum Design ◽  
Heat Pipes ◽  
Micro Heat Pipe ◽  
Capillary Limit ◽  
Heat Transfer Capacity ◽  
Wick Structure ◽  
Micro Heat Pipes

Through combination of experimental investigation with theoretical optimum design, this paper determined the crucial factors in affecting the heat transfer capacity in micro heat pipes with a trapezium-grooved wick structure are capillary limit and entrainment limit, and verified the validity of the heat transfer models thus built.

An Experimental Study of Heat Transfer Characteristics in Miniature Loop Heat Pipes With Rectangular Shaped Evaporator

2011 ◽  
Author(s):  
Z. R. Lin ◽  
Z. Y. Lee ◽  
L. W. Zhang ◽  
S. F. Wang ◽  
A. A. Merrikh ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Sink ◽  
Thermal Design ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Heat Transport Capability

Loop heat pipe (LHP) is a highly efficient cooling device. It has gained great attention in the electronics cooling industry due to its superior heat transport capability — that is, its ability to carry heat over long distances. For this article, a miniature flat loop heat pipe (MFLHP) with rectangular-shaped evaporator was developed. The LHP’s evaporator was combined with the compensation chamber. MFLHPs with different diameters and lengths for the connecting pipeline were selected for a series of experimental studies on their heat transfer characteristics. In these experiments, pure water was used as the working fluid. The studies showed that the heat transport capability of a MFLHP with 4 mm diameter was better than that a MFLHP with 3 mm diameter. At a low thermal resistance of 0.04°C /W (at 200W), an optimal length for the connecting pipeline for a particular MFLHP with 4 mm diameter was identified. Finally, a heat sink attached to a MFLHP was developed for cooling a graphics processing unit (GPU), the thermal design power (TDP) of which was 200 W. The results showed the GPU heat sink with MFLHP had good performance and satisfied GPU cooling requirements. Compared to the conventional heat pipe solutions, only one MFLHP was able to cope with high power dissipation, offering the potential to make a lighter heat sink.

Heat Transport Limitation of a Triangular Micro Heat Pipe

2003 ◽  
Author(s):  
D. Sugumar ◽  
Kek Kiong Tio
Keyword(s):  
Heat Pipe ◽  
Heat Transport ◽  
Operating Temperature ◽  
Working Fluid ◽  
Transport Capacity ◽  
Condenser Section ◽  
Micro Heat Pipe ◽  
Evaporator Section ◽  
Higher Temperature ◽  
Specific Temperature

A micro heat pipe will operate effectively by achieving its maximum possible heat transport capacity only if it is to operate at a specific temperature, i.e., design temperature. In reality, micro heat pipe’s may be required to operate at temperatures different from the design temperature. In this study, the heat transport capacity of an equilateral triangle micro heat pipe is investigated. The micro heat pipe is filled optimally with working fluid for a specific design temperature and operated at different operating temperatures. For this purpose, water, pentane and acetone was selected as the working fluids. From the numerical results obtained, it shows that the optimal charge level of the micro heat pipe is dependent on the operating temperature. Furthermore, the results also shows that if the micro heat pipe is to be operated at temperatures other than its design temperature, its heat transport capacity is limited by the occurrence of flooding at the condenser section or dryout at the evaporator section, depending on the operating temperature and type of working fluid. It is observed that when the micro heat pipe is operated at a higher temperature than its design temperature, the heat transport capacity increases but limited by the onset of dryout at the evaporator section. However, the heat transport capacity decreases if it is to be operated at lower temperatures than its design temperature due to the occurrence of flooding at condenser end. From the results obtained, we can conclude that the performance of a micro heat pipe is decreased if it is to be operated at temperatures other than its design temperature.

Study on a Pulsating Heat Pipe With Self-Rewetting Fluid

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Koji Fumoto ◽  
Masahiro Kawaji ◽  
Tsuyoshi Kawanami
Keyword(s):  
Surface Tension ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heated Surface ◽  
Input Power ◽  
Water Mixture ◽  
Pulsating Heat Pipe ◽  
Maximum Heat ◽  
Dry Spot ◽  
Heat Transport Capability

This paper discusses a pulsating heat pipe (PHP) using a self-rewetting fluid. Unlike other common liquids, self-rewetting fluids have the property that the surface tension increases with temperature. The increasing surface tension at a higher temperature can cause the liquid to be drawn toward a heated surface if a dry spot appears and thus to improve boiling heat transfer. In experiments, 1-butanol and 1-pentanol were added to water at a concentration of less than 1 wt % to make self-rewetting fluid. A pulsating heat pipe made from an extruded multiport tube was partially filled with the self-rewetting fluid water mixture and tested for its heat transport capability at different input power levels. The experiments showed that the maximum heat transport capability was enhanced by a factor of 4 when the maximum heater temperature was limited to 110°C. Thus, the use of a self-rewetting fluid in a PHP was shown to be highly effective in improving the heat transport capability of pulsating heat pipes.

scholarly journals An investigation on effect of EDL on heat transfer of micro heat pipe with square and triangular cross section

2020 ◽  
Vol 21 (3) ◽  
pp. 309
Author(s):  
Maryam Fallah Abbasi ◽  
Hossein Shokouhmand ◽  
Morteza Khayat
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Double Layer ◽  
Electric Double Layer ◽  
Heat Pipes ◽  
The Body ◽  
Working Fluid ◽  
Two Phase ◽  
Micro Heat Pipe ◽  
Micro Heat Pipes

Electronic industries have always been trying to improve the efficiency of electronic devices with small dimensions through thermal management of this equipment, thus increasing the use of small thermal sinks. In this study micro heat pipes with triangular and square cross sections have been manufactured and tested. One of the main objectives is to obtain an understanding of micro heat pipes and their role in energy transmission with electrical double layer (EDL). Micro heat pipes are highly efficient heat transfer devices, which use the continuous evaporation/condensation of a suitable working fluid for two-phase heat transport in a closed system. Since the latent heat of vaporization is very large, heat pipes transport heat at small temperature difference, with high rates. Because of variety of advantage features these devices have found a number of applications both in space and terrestrial technologies. The theory of operation micro heat pipes with EDL is described and the micro heat pipe has been studied. The temperature distribution have achieved through five thermocouples installed on the body. Water and different solution mixture of water and ethanol have used to investigate effect of the electric double layer heat transfer. It was noticed that the electric double layer of ionized fluid has caused reduction of heat transfer.

Sign in / Sign up

Export Citation Format

Share Document