Further Study of Quasiperiodic Vibration Excitation Forces in Rotated Triangular Tube Bundles Subjected to Two-Phase Cross Flow

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
C. Zhang ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Flow Velocity ◽  
Cross Flow ◽  
Fretting Wear ◽  
Force Frequency ◽  
Two Phase ◽  
Vibration Excitation ◽  
Tube Bundles ◽  
Excitation Force ◽  
Lift Forces ◽  
Drag And Lift

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting-wear or fatigue. Detailed vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Some of this work has already been done. Somewhat unexpected but significant quasiperiodic forces in both the drag and lift directions were measured. These forces are generally larger in the drag direction. However, the excitation force frequency is relatively low (i.e., 3–6 Hz) and not directly dependent on flow velocity in the drag direction. On the other hand, much higher frequencies (up to 16 Hz) were observed in the lift direction at the higher flow velocities. The frequency appears directly related to flow velocity in the lift direction. The present work aims at (1) providing further evidence of the quasiperiodic lift force mechanism, (2) determining the effect of cylinder position on such quasiperiodic drag and lift forces, and (3) verifying the existence of quasiperiodic drag and lift forces in a more realistic larger tube array. The program was carried out with two rotated triangular tube arrays of different width subjected to air/water flow to simulate two-phase mixtures from liquid to 95% void fraction. Both the dynamic lift and drag forces were measured with strain gauge instrumented cylinders.

scholarly journals Correlation Between Vibration Excitation Forces and the Dynamic Characteristics of Two-Phase Flow in a Rotated Triangular Tube Bundle

2006 ◽  
Author(s):  
C. Zhang ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Void Fraction ◽  
Cross Flow ◽  
Main Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Drag Forces ◽  
Vibration Excitation ◽  
Tube Bundles ◽  
Lift Forces ◽  
Drag And Lift

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting-wear or fatigue. Detailed flow and vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Some of this work has already been done. The distributions of both void fraction and bubble velocity in rotated-triangular tube bundles were obtained. Somewhat unexpected but significant quasi-periodic forces in both the drag and lift directions were measured. The present work aims at understanding the nature of such unexpected drag and lift quasi-periodic forces. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air/water flow to simulate two-phase mixtures. Fiber-optic probes were developed to measure local void fraction. Both the dynamic lift and drag forces were measured with a strain gage instrumented cylinder. The investigation showed that the quasi-periodic drag and lift forces are generated by different mechanisms that have not been observed so far. The quasi-periodic drag forces appear related to the momentum flux fluctuations in the main flow path between the cylinders. The quasi-periodic lift forces, on the other hand, are mostly correlated to oscillations in the wake of the cylinders. The relationships between the lift or drag forces and the dynamic characteristics of two-phase flow are established through fluid mechanics momentum equations. The quasi-periodic lift forces are related to local void fraction measurements in the unsteady wake area between upstream and downstream cylinders. The quasi-periodic drag forces correlate well with similar measurements in the main flow stream between cylinders.

Correlation Between Vibration Excitation Forces and the Dynamic Characteristics of Two-Phase Cross Flow in a Rotated-Triangular Tube Bundle

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
C. Zhang ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Void Fraction ◽  
Cross Flow ◽  
Main Flow ◽  
Experimental Program ◽  
Two Phase ◽  
Drag Forces ◽  
Vibration Excitation ◽  
Tube Bundles ◽  
Lift Forces ◽  
Drag And Lift

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting wear or fatigue. Detailed flow and vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Some of this work has already been done. The distributions of both void fraction and bubble velocity in rotated-triangular tube bundles were obtained. Somewhat unexpected but significant quasiperiodic forces in both the drag and lift directions were measured. The present work aims at understanding the nature of such unexpected drag and lift quasiperiodic forces. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air/water flow to simulate two-phase mixtures. Fiber-optic probes were developed to measure local void fraction. Both the dynamic lift and drag forces were measured with a strain gage instrumented cylinder. The investigation showed that the quasiperiodic drag and lift forces are generated by different mechanisms that have not been previously observed. The quasiperiodic drag forces appear related to the momentum flux fluctuations in the main flow path between the cylinders. The quasiperiodic lift forces, on the other hand, are mostly correlated to oscillations in the wake of the cylinders. The quasiperiodic lift forces are related to local void fraction measurements in the unsteady wake area between upstream and downstream cylinders. The quasiperiodic drag forces correlate well with similar measurements in the main flow stream between cylinders.

Vibration Excitation Force Measurements in a Rotated Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2005 ◽  
Author(s):  
C. Zhang ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Tube Bundle ◽  
Cross Flow ◽  
Fretting Wear ◽  
Experimental Program ◽  
Force Measurements ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Drag Forces ◽  
Vibration Excitation ◽  
Excitation Force

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting-wear or fatigue. Detailed vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air/water flow to simulate two-phase mixtures over a broad range of void fraction and mass fluxes. Both the dynamic lift and drag forces were measured with strain gage instrumented cylinders. The experiments revealed somewhat unexpected but significant quasi-periodic forces in both the drag and lift directions. The periodic forces appeared well correlated along the cylinder with the drag force somewhat better correlated than the lift forces. The periodic forces are also dependent on the position of the cylinder within the bundle.

Vibration Excitation Force Measurements in a Rotated Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2006 ◽  
Vol 129 (1) ◽  
pp. 21-27 ◽  
Author(s):  
C. Zhang ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Tube Bundle ◽  
Cross Flow ◽  
Fretting Wear ◽  
Experimental Program ◽  
Force Measurements ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Drag Forces ◽  
Vibration Excitation ◽  
Excitation Force

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting-wear or fatigue. Detailed vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air/water flow to simulate two-phase mixtures over a broad range of void fraction and mass fluxes. Both the dynamic lift and drag forces were measured with strain gage instrumented cylinders. The experiments revealed somewhat unexpected but significant quasi-periodic forces in both the drag and lift directions. The periodic forces appeared well correlated along the cylinder with the drag force somewhat better correlated than the lift forces. The periodic forces are also dependent on the position of the cylinder within the bundle.

Vibration Excitation Forces in a Rotated Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2010 ◽  
Author(s):  
H. Senez ◽  
N. W. Mureithi ◽  
M. J. Pettigrew
Keyword(s):  
Steam Generator ◽  
Tube Bundle ◽  
Cross Flow ◽  
Fretting Wear ◽  
Experimental Program ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Fluid Forces ◽  
Vibration Excitation

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting wear or fatigue. Detailed flow and vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Studies on this subject have already been done, providing results on flow regimes, fluidelastic instabilities, and turbulence-induced vibration. The spectrum of turbulence-induced forces has usually been expected to be similar to that in single-phase flow. However, a recent study, using tubes with a diameter larger than that in a real steam generator, showed the existence of significant quasi-periodic forces in two-phase flow. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air-water cross-flow, to simulate two-phase mixtures. The tube bundle here has the same geometry as that of a real steam generator. The quasi-periodic forces have now also been observed in this tube bundle. The present work aims to understand turbulence-induced forces acting on the tube bundle, providing results on drag and lift force spectra and their behaviour according to flow parameters, and describing their correlations. Detailed experimental test results are presented in this paper. Comparison is also made with previous measurements with larger diameter tubes. The present results suggest that quasi-periodic fluid forces are not uncommon in tube arrays subjected to two-phase cross-flow.

Fluid-Elastic Instability of Normal Square Tube Bundles in Two-Phase Cross Flow

2010 ◽  
Author(s):  
Woo Gun Sim ◽  
Mi Yeon Park
Keyword(s):  
Heat Exchanger ◽  
Flow Velocity ◽  
Dynamic Instability ◽  
Cross Flow ◽  
Elastic Instability ◽  
Two Phase ◽  
Critical Flow Velocity ◽  
Tube Heat Exchanger ◽  
Tube Bundles ◽  
Square Array

Some knowledge on damping and fluid-elastic instability is necessary to avoid flow-induced-vibration problems in shell and tube heat exchanger such as steam generator. Fluid-elastic instability is the most important vibration excitation mechanism for heat exchanger tube bundles subjected to the cross flow. Experiments have been performed to investigate fluid-elastic instability of normal square tube bundles, subjected to two-phase cross flow. The test section consists of cantilevered flexible cylinder(s) and rigid cylinders of normal square array. From a practical design point of view, fluid-elastic instability may be expressed simply in terms of dimensionless flow velocity and dimensionless mass-damping parameter. For dynamic instability of cylinder rows, added mass, damping and critical flow velocity are evaluated. The Fluid-elastic instability coefficient is calculated and then compared to existing results given for tube bundles in normal square array.

Vibration Excitation Forces in a Normal Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2011 ◽  
Author(s):  
E. S. Perrot ◽  
N. W. Mureithi ◽  
M. J. Pettigrew ◽  
G. Ricciardi
Keyword(s):  
Tube Bundle ◽  
Cross Flow ◽  
Random Excitation ◽  
Two Phase ◽  
Constant Frequency ◽  
Fluid Forces ◽  
Drag Forces ◽  
Wide Range ◽  
Drag And Lift ◽  
Lift And Drag

This paper presents test results of vibration forces in a normal triangular tube bundle subjected to air-water cross-flow. The dynamic lift and drag forces were measured with strain gage instrumented cylinders. The array has a pitch-to-diameter ratio of 1.5, and the tube diameter is 38 mm. A wide range of void fraction and fluid velocities were tested. The experiments revealed significant forces in both the drag and lift directions. Constant frequency and quasi-periodic fluid forces were found in addition to random excitation. These forces were analyzed and characterized to understand their origins. The forces were found to be dependent on the position of the cylinder within the bundle. The results are compared with those obtained with flexible cylinders in the same tube bundle and to those for a rotated triangular tube bundle. These comparisons reveal the influence of quasi-periodic forces on tube motions.

scholarly journals A Ghost-Cell Immersed Boundary Method for Wave–Structure Interaction Using a Two-Phase Flow Model

Water ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 3346
Author(s):  
Yuan-Shiang Tsai ◽  
Der-Chang Lo
Keyword(s):  
Immersed Boundary Method ◽  
Flow Model ◽  
Two Phase Flow ◽  
Immersed Boundary ◽  
Phase Flow ◽  
Ghost Cell ◽  
Two Phase ◽  
Boundary Method ◽  
Lift Forces ◽  
Drag And Lift

The air-water two-phase flow model is developed to study the transformation of monochromatic waves passing over the submerged structure. The level set method is employed to describe the motion of the interface while the effect of the immersed object on the fluid is resolved using the ghost-cell immersed boundary method. The computational domain integrated with the air-water and fluid-solid phases allows the use of uniform Cartesian grids. The model simulates the wave generation, wave decomposition over a submerged trapezoidal breakwater, and the formation of the vortices as well as the drag and lift forces caused by the surface waves over three different configurations of the submerged structures. The numerical results show the capability of the present model to accurately track the deformation of the free surface. In addition, the variation of the drag and lift forces depend on the wavelength and wave induced vortices around the submerged object. Hence, the study observes that the triangular structure experiences the relatively small wave force.

Development of a Numerical Model for Quasi-Periodic Forces of Two-Phase Cross Flow in Tube Bundles

2014 ◽  
Author(s):  
Sarra Zoghlami ◽  
Cédric Béguin ◽  
Stéphane Étienne
Keyword(s):  
Numerical Model ◽  
Tube Bundle ◽  
Cross Flow ◽  
Deep Understanding ◽  
Added Mass ◽  
Dispersed Phase ◽  
Two Phase ◽  
Induced Drag ◽  
Tube Bundles ◽  
Lagrange Approach

To reduce the damage caused by induced vibrations due to two-phase cross flow on tube bundles in heat exchangers, a deep understanding of the different sources of this phenomenon is required. For this purpose, a numerical model was previously developed to simulate the quasi periodic forces on the tube bundle due to two-phase cross flow. An Euler-Lagrange approach is adopted to describe the flow. The Euler approach describes the continuous phase (liquid) using potential flow. The dispersed phase is assumed to have no interaction on liquid flow. Based on visual observation, static vortices behind the tube are introduced. The Lagrange approach describes the dispersed phase (gas). The model allows bubbles to split up or to coalesce. The forces taken into account acting on the bubbles are the buoyancy, the drag and induced drag, the added mass and induced added mass and impact force (bubble-bubble and bubble-tube). Forces taken into account acting on the tubes are impact forces and induced drag and added mass forces. This model allows us to obtain quasi periodic force on tube induced by two-phase cross flow of relative good magnitude and frequency contains. The model still needs improvement to bring us closer to experimental data of force, for example by introducing a dependency between the void ratio and the intensity of the vortex and by taking into account the bubbles deformation.

Sign in / Sign up

Export Citation Format

Share Document