Wall-Modeled Large-Eddy Simulations of Flows With Curvature and Mild Separation

2008 ◽  
Vol 130 (10) ◽  
Author(s):  
Senthilkumaran Radhakrishnan ◽  
Ugo Piomelli ◽  
Anthony Keating
Keyword(s):  
Friction Coefficient ◽  
Large Eddy Simulation ◽  
Skin Friction ◽  
Outer Region ◽  
Skin Friction Coefficient ◽  
Stochastic Forcing ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Buffer Region ◽  
Large Eddy

The performance of wall-modeled large-eddy simulation (WMLES) based on hybrid models, in which the inner region is modeled by Reynolds-averaged Navier–Stokes (RANS) equation and the outer region is resolved by large-eddy simulation (LES), can make the application of LES attainable at high Reynolds numbers. In previous work by various authors, it was found that in most cases a buffer region exists between the RANS and LES zones, in which the velocity gradient is too high; this leads to an inaccurate prediction of the skin-friction coefficient. Artificially perturbing the RANS∕LES interface has been demonstrated to be effective in removing the buffer region. In this work, WMLES has been performed with stochastic forcing at the interface, following the previous work by our group on two nonequilibrium complex flows. From the two flows studied, we conclude that the application of stochastic forcing results in improvements in the prediction of the skin-friction coefficient in the equilibrium regions of these flows, a better agreement with the experiments of the Reynolds stresses in the adverse pressure gradient and the recovery region, and a good agreement of the mean velocity field with experiments in the separation region. Some limitations of this method, especially in terms of CPU requirements, will be discussed.

Large-eddy simulation of flow over a cylinder with from to : a skin-friction perspective

2017 ◽  
Vol 820 ◽  
pp. 121-158 ◽  
Author(s):  
W. Cheng ◽  
D. I. Pullin ◽  
R. Samtaney ◽  
W. Zhang ◽  
W. Gao
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Large Eddy Simulation ◽  
Skin Friction ◽  
Flow Separation ◽  
Skin Friction Coefficient ◽  
Cylinder Surface ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy

We present wall-resolved large-eddy simulations (LES) of flow over a smooth-wall circular cylinder up to$Re_{D}=8.5\times 10^{5}$, where$Re_{D}$is Reynolds number based on the cylinder diameter$D$and the free-stream speed$U_{\infty }$. The stretched-vortex subgrid-scale (SGS) model is used in the entire simulation domain. For the sub-critical regime, six cases are implemented with$3.9\times 10^{3}\leqslant Re_{D}\leqslant 10^{5}$. Results are compared with experimental data for both the wall-pressure-coefficient distribution on the cylinder surface, which dominates the drag coefficient, and the skin-friction coefficient, which clearly correlates with the separation behaviour. In the super-critical regime, LES for three values of$Re_{D}$are carried out at different resolutions. The drag-crisis phenomenon is well captured. For lower resolution, numerical discretization fluctuations are sufficient to stimulate transition, while for higher resolution, an applied boundary-layer perturbation is found to be necessary to stimulate transition. Large-eddy simulation results at$Re_{D}=8.5\times 10^{5}$, with a mesh of$8192\times 1024\times 256$, agree well with the classic experimental measurements of Achenbach (J. Fluid Mech., vol. 34, 1968, pp. 625–639) especially for the skin-friction coefficient, where a spike is produced by the laminar–turbulent transition on the top of a prior separation bubble. We document the properties of the attached-flow boundary layer on the cylinder surface as these vary with$Re_{D}$. Within the separated portion of the flow, mean-flow separation–reattachment bubbles are observed at some values of$Re_{D}$, with separation characteristics that are consistent with experimental observations. Time sequences of instantaneous surface portraits of vector skin-friction trajectory fields indicate that the unsteady counterpart of a mean-flow separation–reattachment bubble corresponds to the formation of local flow-reattachment cells, visible as coherent bundles of diverging surface streamlines.

scholarly journals Large-eddy simulation of the zero-pressure-gradient turbulent boundary layer up to Reθ = O(1012)

2011 ◽  
Vol 686 ◽  
pp. 507-533 ◽  
Author(s):  
M. Inoue ◽  
D. I. Pullin
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Turbulent Boundary Layer ◽  
Large Eddy Simulation ◽  
Pressure Gradient ◽  
Skin Friction Coefficient ◽  
Smooth Wall ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Near Wall

AbstractA near-wall subgrid-scale (SGS) model is used to perform large-eddy simulation (LES) of the developing, smooth-wall, zero-pressure-gradient flat-plate turbulent boundary layer. In this model, the stretched-vortex, SGS closure is utilized in conjunction with a tailored, near-wall model designed to incorporate anisotropic vorticity scales in the presence of the wall. Large-eddy simulations of the turbulent boundary layer are reported at Reynolds numbers ${\mathit{Re}}_{\theta } $ based on the free-stream velocity and the momentum thickness in the range ${\mathit{Re}}_{\theta } = 1{0}^{3} \text{{\ndash}} 1{0}^{12} $. Results include the inverse square-root skin-friction coefficient, $ \sqrt{2/ {C}_{f} } $, velocity profiles, the shape factor $H$, the von Kármán ‘constant’ and the Coles wake factor as functions of ${\mathit{Re}}_{\theta } $. Comparisons with some direct numerical simulation (DNS) and experiment are made including turbulent intensity data from atmospheric-layer measurements at ${\mathit{Re}}_{\theta } = O(1{0}^{6} )$. At extremely large ${\mathit{Re}}_{\theta } $, the empirical Coles–Fernholz relation for skin-friction coefficient provides a reasonable representation of the LES predictions. While the present LES methodology cannot probe the structure of the near-wall region, the present results show turbulence intensities that scale on the wall-friction velocity and on the Clauser length scale over almost all of the outer boundary layer. It is argued that LES is suggestive of the asymptotic, infinite Reynolds number limit for the smooth-wall turbulent boundary layer and different ways in which this limit can be approached are discussed. The maximum ${\mathit{Re}}_{\theta } $ of the present simulations appears to be limited by machine precision and it is speculated, but not demonstrated, that even larger ${\mathit{Re}}_{\theta } $ could be achieved with quad- or higher-precision arithmetic.

scholarly journals Assessing IDDES-Based Wall-Modeled Large-Eddy Simulation (WMLES) for Separated Flows with Heat Transfer

Fluids ◽  
2021 ◽  
Vol 6 (7) ◽  
pp. 246
Author(s):  
Rozie Zangeneh
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Large Eddy Simulation ◽  
Skin Friction ◽  
Heat Fluxes ◽  
Separated Flows ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Isothermal Wall

The Wall-modeled Large-eddy Simulation (WMLES) methods are commonly accompanied with an underprediction of the skin friction and a deviation of the velocity profile. The widely-used Improved Delayed Detached Eddy Simulation (IDDES) method is suggested to improve the prediction of the mean skin friction when it acts as WMLES, as claimed by the original authors. However, the model tested only on flow configurations with no heat transfer. This study takes a systematic approach to assess the performance of the IDDES model for separated flows with heat transfer. Separated flows on an isothermal wall and walls with mild and intense heat fluxes are considered. For the case of the wall with heat flux, the skin friction and Stanton number are underpredicted by the IDDES model however, the underprediction is less significant for the isothermal wall case. The simulations of the cases with intense wall heat transfer reveal an interesting dependence on the heat flux level supplied; as the heat flux increases, the IDDES model declines to predict the accurate skin friction.

Large eddy simulation study of turbulent flow around smooth and rough domes

2013 ◽  
Vol 227 (12) ◽  
pp. 2686-2700 ◽  
Author(s):  
N Kharoua ◽  
L Khezzar
Keyword(s):  
Large Eddy Simulation ◽  
Turbulent Flow ◽  
Flow Behavior ◽  
Pressure Coefficient ◽  
Horseshoe Vortex ◽  
Scale Model ◽  
Stream Velocity ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Large Eddy

Large eddy simulation of turbulent flow around smooth and rough hemispherical domes was conducted. The roughness of the rough dome was generated by a special approach using quadrilateral solid blocks placed alternately on the dome surface. It was shown that this approach is capable of generating the roughness effect with a relative success. The subgrid-scale model based on the transport of the subgrid turbulent kinetic energy was used to account for the small scales effect not resolved by large eddy simulation. The turbulent flow was simulated at a subcritical Reynolds number based on the approach free stream velocity, air properties, and dome diameter of 1.4 × 105. Profiles of mean pressure coefficient, mean velocity, and its root mean square were predicted with good accuracy. The comparison between the two domes showed different flow behavior around them. A flattened horseshoe vortex was observed to develop around the rough dome at larger distance compared with the smooth dome. The separation phenomenon occurs before the apex of the rough dome while for the smooth dome it is shifted forward. The turbulence-affected region in the wake was larger for the rough dome.

Kinetic-energy-flux-constrained model using an artificial neural network for large-eddy simulation of compressible wall-bounded turbulence

2021 ◽  
Vol 932 ◽  
Author(s):  
Changping Yu ◽  
Zelong Yuan ◽  
Han Qi ◽  
Jianchun Wang ◽  
Xinliang Li ◽  
...  
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Kinetic Energy ◽  
Large Eddy Simulation ◽  
Energy Flux ◽  
Mean Velocity ◽  
New Model ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Wall Bounded Turbulence

Kinetic energy flux (KEF) is an important physical quantity that characterizes cascades of kinetic energy in turbulent flows. In large-eddy simulation (LES), it is crucial for the subgrid-scale (SGS) model to accurately predict the KEF in turbulence. In this paper, we propose a new eddy-viscosity SGS model constrained by the properly modelled KEF for LES of compressible wall-bounded turbulence. The new methodology has the advantages of both accurate prediction of the KEF and strong numerical stability in LES. We can obtain an approximate KEF by the tensor-diffusivity model, which has a high correlation with the real value. Then, using the artificial neural network method, the local ratios between the real KEF and the approximate KEF are accurately modelled. Consequently, the SGS model can be improved by the product of that ratio and the approximate KEF. In LES of compressible turbulent channel flow, the new model can accurately predict mean velocity profile, turbulence intensities, Reynolds stress, temperature–velocity correlation, etc. Additionally, for the case of a compressible flat-plate boundary layer, the new model can accurately predict some key quantities, including the onset of transitions and transition peaks, the skin-friction coefficient, the mean velocity in the turbulence region, etc., and it can also predict the energy backscatters in turbulence. Furthermore, the proposed model also shows more advantages for coarser grids.

An Experimental Study of a Turbulent Wall Jet on Smooth and Transitionally Rough Surfaces

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
N. Rostamy ◽  
D. J. Bergstrom ◽  
D. Sumner ◽  
J. D. Bugg
Keyword(s):  
Friction Coefficient ◽  
Skin Friction ◽  
Laser Doppler Anemometry ◽  
Skin Friction Coefficient ◽  
Wall Jet ◽  
Roughness Effects ◽  
Mean Velocity ◽  
Turbulent Wall ◽  
Inner Region ◽  
Effect Of Surface

The effect of surface roughness on the mean velocity and skin friction characteristics of a plane turbulent wall jet was experimentally investigated using laser Doppler anemometry. The Reynolds number based on the slot height and exit velocity of the jet was approximately Re = 7500. A 36-grit sheet was used to create a transitionally rough flow (44 < ks+ < 70). Measurements were carried out at downstream distances from the jet exit ranging from 20 to 80 slot heights. Both conventional and momentum-viscosity scaling were used to analyze the streamwise evolution of the flow on smooth and rough walls. Three different methods were employed to estimate the friction velocity in the fully developed region of the wall jet, which was then used to calculate the skin friction coefficient. This paper provides new experimental data for the case of a plane wall jet on a transitionally rough surface and uses it to quantify the effects of roughness on the momentum field. The present results indicate that the skin friction coefficient for the rough-wall case compared to a smooth wall increases by as much as 140%. Overall, the study suggests that for the transitionally rough regime considered in the present study, roughness effects are significant but mostly confined to the inner region of the wall jet.

Large-Eddy Simulation of a Swirl-Stabilized, Lean Direct Injection Spray Combustor

2006 ◽  
Author(s):  
Mehmet Kırtas¸ ◽  
Nayan Patel ◽  
Vaidyanathan Sankaran ◽  
Suresh Menon
Keyword(s):  
Large Eddy Simulation ◽  
Vortex Breakdown ◽  
Direct Injection ◽  
Reacting Flow ◽  
Mean Velocity ◽  
Recirculation Bubble ◽  
Lean Direct Injection ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Recirculation Zones

Large-eddy simulation (LES) of a lean-direct injection (LDI) combustor is reported in this paper. The full combustor and all the six swirl vanes are resolved and both cold and reacting flow simulations are performed. Cold flow predictions with LES indicate the presence of a broad central recirculation zone due to vortex breakdown phenomenon near the dump plane and two corner recirculation zones at the top and bottom corner of the combustor. These predicted features compare well with the experimental non-reacting data. Reacting case simulated a liquid Jet-A fuel spray using a Lagrangian approach. A three-step kinetics model that included CO and NO is used for the chemistry. Comparison of mean velocity field predicted in the reacting LES with experiments shows reasonable agreement. Comparison with the non-reacting case shows that the centerline recirculation bubble is shorter but more intense in the reacting case.

Large-eddy simulation and parameterization of buoyant plume dynamics in stratified flow

2016 ◽  
Vol 794 ◽  
pp. 798-833 ◽  
Author(s):  
Di Yang ◽  
Bicheng Chen ◽  
Scott A. Socolofsky ◽  
Marcelo Chamecki ◽  
Charles Meneveau
Keyword(s):  
Large Eddy Simulation ◽  
Large Fraction ◽  
Bubble Plume ◽  
Mean Velocity ◽  
Neutral Buoyancy ◽  
Buoyant Plumes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Consistent Manner ◽  
Trap Height

Characteristics of laboratory-scale bubble-driven buoyant plumes in a stably stratified quiescent fluid are studied using large-eddy simulation (LES). As a bubble plume entrains stratified ambient water, its net buoyancy decreases due to the increasing density difference between the entrained and ambient fluids. A large fraction of the entrained fluid eventually detrains and falls along an annular outer plume from a height of maximum rise (peel height) to a neutral buoyancy level (trap height), during which less buoyant scalars (e.g. small droplets) are trapped and dispersed horizontally, forming quasi-horizontal intrusion layers. The inner/outer double-plume structure and the peel/intrusion process are found to be more distinct for cases with small bubble rise velocity, while weak and unstable when the slip velocity is large. LES results are averaged to generate distributions of mean velocity and turbulent fluxes. These distributions provide data for assessing the performance of previously developed closures used in one-dimensional integral plume models. In particular, the various LES cases considered in this study yield consistent behaviour for the entrainment coefficients for various plume cases. Furthermore, a new continuous peeling model is derived based on the insights obtained from LES results. Comparing to previous peeling models, the new model behaves in a more self-consistent manner, and it is expected to provide more reliable performance when applied in integral plume models.

Experimental Investigation of Turbulent Boundary Layers Under Favorable Pressure Gradient

2010 ◽  
Author(s):  
Pranav Joshi ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Velocity Profiles ◽  
Skin Friction Coefficient ◽  
Mean Velocity ◽  
Freestream Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

The goal of this research is to study the effect of favorable pressure gradient (FPG) on the near wall structures of a turbulent boundary layer on a smooth wall. 2D-PIV measurements have been performed in a sink flow, initially at a coarse resolution, to characterize the development of the mean flow and (under resolved) Reynolds stresses. Lack of self-similarity of mean velocity profiles shows that the boundary layer does not attain the sink flow equilibrium. In the initial phase of acceleration, the acceleration parameter, K = v/U2dU/dx, increases from zero to 0.575×10−6, skin friction coefficient decreases and mean velocity profiles show a log region, but lack universality. Further downstream, K remains constant, skin friction coefficient increases and the mean velocity profiles show a second log region away from the wall. In the initial part of the FPG region, all the Reynolds stress components decrease over the entire boundary layer. In the latter phase, they continue to decrease in the middle of the boundary layer, and increase significantly close to the wall (below y∼0.15δ), where they collapse when normalized with the local freestream velocity. Turbulence production and wallnormal transport, scaled with outer units, show self-similar profiles close to the wall in the constant K region. Spanwise-streamwise plane data shows evidence of low speed streaks in the log layer, with widths scaling with the boundary layer thickness.

Sign in / Sign up

Export Citation Format

Share Document