Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1990 ◽  
Vol 112 (1) ◽  
pp. 133-144 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was to clarify the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high-blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment; injection can also contribute significantly to stall suppression. The results indicate that the increase in stall pressure rise achieved with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

scholarly journals Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1989 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was clarification of the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment, as injection can also contribute significantly to stall suppression. The results also indicate that the increase in stall pressure rise with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

Stability Enhancement by Casing Grooves: The Importance of Stall Inception Mechanism and Solidity

2010 ◽  
Author(s):  
Tim Houghton ◽  
Ivor Day
Keyword(s):  
Companion Paper ◽  
Rotor Blades ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stable Operating ◽  
Before And After ◽  
Stall Margin Improvement ◽  
Prediction Techniques ◽  
Stability Enhancement

This paper concerns the optimisation of casing grooves and the important influence of stall inception mechanism on groove performance. Installing casing grooves is a well known technique for improving the stable operating range of a compressor, but the wide-spread use of grooves is restricted by the loss of efficiency and flow capacity. In this paper, laboratory tests are used to examine the conditions under which casing treatment can be used to greatest effect. The use of a single casing groove was investigated in a recently published companion paper. The current work extends this to multiple-groove treatments and considers their performance in relation to stall inception mechanisms. Here it is shown that the stall margin gain from multiple grooves is less than the sum of the gains if the grooves were used individually. By contrast, the loss of efficiency is additive as the number of grooves increases. It is then shown that casing grooves give the greatest stall margin improvement when used in a compressor which exhibits spike-type stall inception, while modal activity before stall can dramatically reduce the effectiveness of the grooves. This finding highlights the importance of being able to predict the stall inception mechanism which might occur in a given compressor before and after grooves are added. Some published prediction techniques are therefore examined, but found wanting. Lastly, it is shown that casing grooves can, in some cases, be used to remove rotor blades and produce a more efficient, stable and light-weight rotor.

scholarly journals Recessed Casing Treatment Effects on Fan Performance and Flow Field

1995 ◽  
Author(s):  
C. S. Kang ◽  
A. B. McKenzie ◽  
R. L. Elder
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Pressure Rise ◽  
Operating Efficiency ◽  
Flow Measurements ◽  
Blade Loading ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement ◽  
Blade Tip

An experimental investigation to examine the influence of the vaned recess casing treatment on stall margin, operating efficiency and the flow field of a low speed axial flow fan with aerospace type blade loading is presented. Different geometrical designs of the vaned passages were examined. The best configuration resulted in a stall margin improvement of 67%, a significantly higher pressure rise in the stall region and insignificant change in peak efficiency. Detailed 3-D flow measurements in the endwall region and in the casing recess were carried out with a slanted hot-wire, providing some insight to the operation of the device. The results revealed that the stall margin improvement was largely due to the removal of flow from the blade tip to the recess, and the elimination of the growth of the stall region at the tip, which occurs at stall in the solid casing build.

Experimental and Numerical Investigation of Effect of Center Offset Degree on Compressor Stability With Circumferential Grooved Casing Treatment

2016 ◽  
Author(s):  
HaoGuang Zhang ◽  
Feng Tan ◽  
YanHui Wu ◽  
WuLi Chu ◽  
Wei Wang ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Groove Depth ◽  
Tip Clearance ◽  
Central Difference ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Blade Tip

For compressor blade tip stall, one effective way of extending stable operating range is with the application of circumferential grooved casing treatment and its validity was proved by a lot of experimental and numerical investigations. The emphases of most circumferential grooved investigations are focused on the influence of groove depth and groove number on compressor stability, and there is few investigations dealt with the center offset degree of circumferential grooves casing treatment. Hence, an axial compressor rotor with casing treatment (CT) was investigated with experimental and numerical methods to explore the effect of center offset degree on compressor stability and performance. In the work reported here, The center offset degree is defined as the ratio of the central difference between rotor tip axial chord and CT to the axial chord length of rotor tip. When the center of CT is located within the upstream direction of the center of rotor tip axial chord, the value of center offset degree is positive. The experimental and numerical results show that stall margin improvement gained with CT is reduced as the value of center offset degree varies from 0 to 0.33 or −0.33, and the CT with −0.33 center offset degree achieves the lowest value of stall margin improvement at 53% and 73% design rotational speed. The detailed analysis of the flow-field in compressor tip indicates that there is not positive effect made by grooves on leading edge of rotor blade tip when the value of center offset degree is −0.33. As the mass flow of compressor reduces further, tip clearance leakage flow results in the outlet blockage due to the absence of the positive action of grooves near blade tip tail when the value of center offset degree is 0.33. Blockage does not appear in rotor tip passage owing to utilizing the function of all grooves with CT of 0 center offset degree.

Numerical Investigation on Slot Casing Treatment in a Transonic Axial Compressor Stage: Part 1 — Casing Treatment Design

2016 ◽  
Author(s):  
Mingmin Zhu ◽  
Xiaoqing Qiang ◽  
Jinfang Teng
Keyword(s):  
Axial Compressor ◽  
Leakage Flow ◽  
Compressor Stage ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Stall Margin ◽  
Rotating Speed ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Stall Margin Improvement

Slot-type casing treatment generally has a great potential of enhancing the operating range for tip-critical compressor rotors, however, with remarkable efficiency drop. Part I of this two-part paper was committed to develop a slot configuration with desired stall margin improvement and minimized efficiency loss. Steady simulation was carried out in a 1.5 transonic axial compressor stage at part design rotating speed. At this rotating speed this compressor stage operated at a subsonic condition and showed a rather narrow operating range, which needed to be improved badly. Flow fields analysis at peak efficiency and near stall point showed that the development of tip leakage vortex and resulting blockage near casing resulted in numerical stall. Three kinds of skewed slots with same rotor exposure and casing porosity were designed according to the tip flow field and some empirical strategies. Among three configurations, arc-curved skewed slot showed minimum peak efficiency drop with considerable stall margin improvement. Then rotor exposure and casing porosity were varied based on the original arc-curved skewed slot, with a special interest in detecting their impact on the compressor stability and overall efficiency. Result showed that smaller rotor exposure and casing porosity leaded to less efficiency drop. But meanwhile, effectiveness of improving compressor stability was weakened. The relation between efficiency drop and stall margin improvement fell on a smooth continuous curve throughout all slots configurations, indicating that the detrimental effect of casing treatment on compressor was inevitable. Flow analysis was carried out for cases of smooth casing and three arc-curved configurations at smooth casing near stall condition. The strength of suction/injection, tip leakage flow behavior and removal of blockage near casing were detailed examined. Larger rotor tip exposure and slots number contributed to stronger injection flow. The loss generated within the mixing process of injection flow with main flow and leakage flow is the largest source of entropy increase. Further loss mechanisms were interpreted at eight axial cuts, which were taken through the blade row and slots to show the increase in entropy near tip region. Entropy distributions manifested that loss generations with smooth casing were primarily ascribed to low-momentum tip leakage flow/vortex and suction surface separation at leading edge. CU0 slot, the arc-curved slots with 50% rotor tip exposure, was capable of suppressing the suction surface separation loss. Meanwhile, accelerated tip leakage flow brought about additional loss near casing and pressure surface. Upstream high entropy flow would be absorbed into the rear portion of slots repeatedly, resulting in further loss.

Stability Enhancement by Casing Grooves: The Importance of Stall Inception Mechanism and Solidity

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Tim Houghton ◽  
Ivor Day
Keyword(s):  
Companion Paper ◽  
Rotor Blades ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stable Operating ◽  
Before And After ◽  
Stall Margin Improvement ◽  
Prediction Techniques ◽  
Stability Enhancement

This paper concerns the optimization of casing grooves and the important influence of stall inception mechanism on groove performance. Installing casing grooves is a well known technique for improving the stable operating range of a compressor, but the wide-spread use of grooves is restricted by the loss of efficiency and flow capacity. In this paper, laboratory tests are used to examine the conditions under which casing treatment can be used to greatest effect. The use of a single casing groove was investigated in a recently published companion paper. The current work extends this to multiple-groove treatments and considers their performance in relation to stall inception mechanisms. Here it is shown that the stall margin gain from multiple grooves is less than the sum of the gains if the grooves were used individually. By contrast, the loss of efficiency is additive as the number of grooves increases. It is then shown that casing grooves give the greatest stall margin improvement when used in a compressor, that exhibits spike-type stall inception, while modal activity before stall can dramatically reduce the effectiveness of the grooves. This finding highlights the importance of being able to predict which stall inception mechanism might occur in a given compressor before and after grooves are added. Some published prediction techniques are therefore examined, but found wanting. Lastly, it is shown that casing grooves can, in some cases, be used to remove rotor blades and produce a more efficient, stable, and light-weight rotor.

scholarly journals Stall margin improvement in a low-speed axial compressor rotor using a blockage-optimised single circumferential casing groove

2021 ◽  
Vol 5 ◽  
pp. 79-89
Author(s):  
Ahmad Fikri Mustaffa ◽  
Vasudevan Kanjirakkad
Keyword(s):  
Axial Compressor ◽  
Pressure Rise ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Low Speed ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Edge Based

The stall margin of tip-critical axial compressors can be improved by using circumferential casing grooves. From previous studies, in the literature, the stall margin improvement due to the casing grooves can be attributed to the reduction of the near casing blockage. The pressure rise across the compressor as the compressor is throttled intensifies the tip leakage flow. This results in a stronger tip leakage vortex that is thought to be the main source of the blockage. In this paper, the near casing blockage due to the tip region aerodynamics in a low-speed axial compressor rotor is numerically studied and quantified using a mass flow-based blockage parameter. The peak blockage location at the last stable operating point for a rotor with smooth casing is found to be at about 10% of the tip chord aft of the tip leading edge. Based on this information, an optimised single casing groove design that minimises the peak blockage is found using a surrogate-based optimisation approach. The implementation of the optimised groove is shown to produce a stall margin improvement of about 5%.

Computational Analysis of Passive Stall Delay Through Vaned Recess Treatment

2001 ◽  
Author(s):  
A. Ghila ◽  
A. Tourlidakis
Keyword(s):  
Axial Flow ◽  
Pressure Rise ◽  
Navier Stokes ◽  
Working Mechanism ◽  
Significant Drop ◽  
Stall Margin ◽  
Casing Treatment ◽  
Work Input ◽  
Stall Margin Improvement ◽  
Casing Treatments

This paper presents a computational investigation of flows in a single axial flow fan with and without casing treatment. It analyses the effect of the recess casing treatment on stall margin improvement as well as its influence on global performance parameters. The paper seeks to offer a contribution to the understanding of the physical processes occurring when approaching stall and the working mechanism by which casing treatments improve stall margin. A Reynolds-Averaged Navier-Stokes CFD code was used for the analysis and the numerical investigation of the overall performance, efficiency and work-input characteristics of the fan were found to agree very well with previously reported experimental results. The effect of casing treatment was investigated using two types of configurations, vaneless and vaned casing. The vaneless casing treatment produced a sizeable stall margin improvement with negligible loss of efficiency. The recess was fitted later with vanes and was shown to offer both a further stall margin improvement and an increase in the pressure rise coefficient without any significant drop in efficiency at design conditions.

Stall Margin Improvement by Casing Treatment—Its Mechanism and Effectiveness

1977 ◽  
Vol 99 (1) ◽  
pp. 121-133 ◽  
Author(s):  
H. Takata ◽  
Y. Tsukuda
Keyword(s):  
Axial Flow ◽  
Stall Margin ◽  
Low Speed ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Flow Through ◽  
Compressor Performance ◽  
Axial Flow Compressors

Experiments on the effect of casing treatment were carried out using low-speed axial-flow compressors. Results on the overall compressor performance and on the flow through the blade row as well as the flow within the treatment slots are presented. Then, based on the experiments, a possible mechanism of the stall margin improvement is suggested.

Computational Analysis of Recess Vane Geometry Modification in the Casing Treatment Approach to Enhance Stall Margin in Axial Flow Fans

2013 ◽  
Author(s):  
Kiran Yelmar ◽  
K. Viswanath
Keyword(s):  
Treatment Approach ◽  
Great Influence ◽  
Flow Characteristics ◽  
Axial Flow ◽  
Pressure Rise ◽  
Axial Flow Fan ◽  
Stall Margin ◽  
Casing Treatment ◽  
Operating Range ◽  
Stall Margin Improvement

Stall margin improvement, though finite, has great influence on performance of a compressor and fan. Modification to the geometry of the recess and the recess vane used in the recess vane casing treatment approach would increase the operating range of an axial flow fan by removing the whirl component of circulatory flow near the blade tip. The present paper investigates the combined effect of variation of recess height and amount of blade chord exposure on flow characteristics and stall margin in low speed axial flow fan. Numerical simulations and modeling was performed using CFX 13.0 and ICEMCFD. The simulated pressure rise, work input and efficiency characteristics agreed well with the experimental data of a low sped fan obtained from the literature. The range of the flow rates which correspond to the stall free operating range of the untreated fan is compared with the same for the different modifications carried out to the geometry. The sensitivity of the operating range to the modifications is analyzed and the effect of recess vane geometry parameters on stall margin improvement is evaluated. Simulations suggest that within the ranges of parameters investigated stall margin improvement increases with both blade chord exposure and height.

Sign in / Sign up

Export Citation Format

Share Document