Fatigue Analysis of a Planarpak™ Surface Mount Component

1991 ◽  
Vol 113 (2) ◽  
pp. 194-199 ◽  
Author(s):  
I. Sharif ◽  
D. B. Barker ◽  
A. Dasgupta ◽  
M. G. Pecht
Keyword(s):  
Fatigue Life ◽  
Thermal Stresses ◽  
Three Dimensional ◽  
Printed Wiring Board ◽  
Surface Mount ◽  
Dimensional Finite Element ◽  
Life Analysis ◽  
Fatigue Life Analysis ◽  
Wiring Board ◽  
Three Dimensional Finite Element

This paper discusses the thermo-mechanical fatigue life analysis of an analog Avantek Planarpak™ surface mount device where the entire base of the component is soldered directly to the printed wiring board. The critical thermal stresses and strains are analyzed with the help of two and three-dimensional finite element models. The effect of solder voids and incomplete bonding is also investigated. The paper also shows how fatigue life estimations can be made using q generalized form of the Manson-Coffin equation even though the maximum solder attach stresses are found to be elastic.

The Fatigue Life Analysis of the Crosshead Based on ANSYS

2011 ◽  
Vol 121-126 ◽  
pp. 4208-4212 ◽  
Author(s):  
Xin Mei Yuan ◽  
Si Zhu Zhou ◽  
Tian Cheng Huang
Keyword(s):  
Finite Element ◽  
High Stress ◽  
Three Dimensional ◽  
Distribution Law ◽  
Element Analysis ◽  
Plunger Pump ◽  
Dimensional Finite Element ◽  
Life Analysis ◽  
Fatigue Life Analysis ◽  
Three Dimensional Finite Element

With three-dimensional finite element method, the crosshead of plunger pump was analyzed. The distribution law of stress at the crosshead was obtained and the stress concentration coefficient of high stress field was calculated. The life of crosshead was estimated by S-N curve of crosshead and the result of finite element analysis, which provides basis of estimating life of the crosshead.

scholarly journals Three-Dimensional Finite Element Modeling of Thermomechanical Problems in Functionally Graded Hydroxyapatite/Titanium Plate

2014 ◽  
Vol 2014 ◽  
pp. 1-20 ◽  
Author(s):  
S. N. S. Jamaludin ◽  
S. Basri ◽  
Ahmad Hussain ◽  
Dheya Shujaa Al-Othmany ◽  
F. Mustapha ◽  
...  
Keyword(s):  
Thermal Stresses ◽  
Three Dimensional ◽  
Metallic Phase ◽  
Functionally Graded ◽  
Thermomechanical Model ◽  
Graded Materials ◽  
Ceramic Phase ◽  
Fg Plates ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The composition of hydroxyapatite (HA) as the ceramic phase and titanium (Ti) as the metallic phase in HA/Ti functionally graded materials (FGMs) shows an excellent combination of high biocompatibility and high mechanical properties in a structure. Because the gradation of these properties is one of the factors that affects the response of the functionally graded (FG) plates, this paper is presented to show the domination of the grading parameter on the displacement and stress distribution of the plates. A three-dimensional (3D) thermomechanical model of a 20-node brick quadratic element is used in the simulation of the thermoelastic behaviors of HA/Ti FG plates subjected to constant and functional thermal, mechanical, and thermomechanical loadings. The convergence properties of the present results are examined thoroughly in order to assess the accuracy of the theory applied and to compare them with the established research results. Instead of the grading parameter, this study reveals that the loading field distribution can be another factor that reflects the thermoelastic properties of the HA/Ti FG plates. The FG structure is found to be able to withstand the thermal stresses while preserving the high toughness properties and thus shows its ability to operate at high temperature.

A Simplified Thermal Load Evaluation Method for Localized Lug Stresses Beyond Sec. III Appendix-Y

2019 ◽  
Author(s):  
Tsubasa Matsumiya ◽  
Daniel Garcia-Rodriguez ◽  
Akira Nebu ◽  
Noriyuki Takamura
Keyword(s):  
Thermal Stresses ◽  
Evaluation Method ◽  
Three Dimensional ◽  
Parameter Study ◽  
Element Analysis ◽  
Class 1 ◽  
Dimensional Finite Element ◽  
3D Fea ◽  
Three Dimensional Finite Element ◽  
Load Evaluation

Abstract In this work an evaluation method for local thermal stresses on class 1 piping due to U-shaped lugs is presented. First, a three-dimensional finite element analysis (3D-FEA) is used to perform a thermal transient evaluation, obtaining the time-dependent temperature distribution of a realistic range of pipe-lug systems. These results are then used as an input for both a structural 3D-FEA and the corresponding thermal stress term in Non-Mandatory Appendix Y [1]. It was seen that the formula in Appendix-Y cannot account for the thermal stresses obtained through the detailed FEA evaluation. A parameter study using a simplified two-dimensional (2D) FEA approach, shows that the localized thermal stresses due to lugs are significantly affected by: (1) pipe-to-lug thickness ratio, (2) distance between adjacent lugs, and (3) lug height. A set of correction coefficients depending on these parameters is therefore proposed. When applying the proposed correction coefficients to the Appendix Y method, adequately conservative (when compared with 3D FEA results) stresses can be obtained. Since these correction coefficients can be obtained from simple geometric considerations, the proposed method successfully accounts for the complex lug-to-lug interaction while retaining the simplicity of the original Appendix Y approach.

FINITE ELEMENT ANALYSIS OF THE THERMAL BEHAVIOUR OF SINGLE-DISC CLUTCHES DURING REPEATED ENGAGEMENTS

Tribologia ◽  
2016 ◽  
Vol 266 (2) ◽  
pp. 9-24 ◽  
Author(s):  
Oday I. ABDULLAH ◽  
Laith Abed SABRI ◽  
Wassan S. Abd Al-SAHB
Keyword(s):  
Finite Element ◽  
Thermal Behaviour ◽  
Thermal Stresses ◽  
Three Dimensional ◽  
Finite Element Models ◽  
Element Analysis ◽  
Premature Failure ◽  
Friction Clutch ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

Most of the failures in the sliding systems occur due to the high thermal stresses, which generated at the interface between the contacting surfaces due to sliding between parts, such as friction clutches and brakes. In this paper, the thermal behaviour of a single-disc clutch is investigated. The surface temperatures of the friction clutch disc will be increased during repeated engagements, in some cases, will lead to premature failure of the clutch disc. In order to avoid this kind of failure, it the surface temperature should be calculated with high accuracy to know the maximum working temperature of the friction system. In this work, the temperature distributions are computed during four repeated engagements at regular intervals (5 s) for the same energy dissipation. Three-dimensional finite element models are used to simulate the typical friction clutch disc.

External Longitudinal Flaws in Pipes Under Complex Loading

2000 ◽  
Vol 123 (1) ◽  
pp. 139-145 ◽  
Author(s):  
Roberto Brighenti
Keyword(s):  
Thermal Stresses ◽  
Superposition Principle ◽  
Three Dimensional ◽  
Complex Loading ◽  
Stress Distributions ◽  
Power Series Expansions ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Hoop Stresses ◽  
Crack Faces

A round pipe with an external longitudinal surface flaw is assumed to be subjected to different types of elementary hoop stress distributions acting perpendicular to the crack faces. The stress intensity factors (SIFs) along the crack front for such elementary cases are determined through the three-dimensional finite element method. Then these results are used to compute approximate values of SIFs in the case of complex loadings (such as internal pressure, thermal stresses, residual stresses due to plasticization, etc.), by employing both the superposition principle and the power series expansions of the actual hoop stresses. Thick and thin-walled pipes are examined, and some results are compared with those presented by other authors.

Mechanics Research with Prediction on the Fatigue Life of the Five-Cylinder Emulsion Pump Crankshaft

2013 ◽  
Vol 738 ◽  
pp. 163-166 ◽  
Author(s):  
Li Ran
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Working Conditions ◽  
Maximum Stress ◽  
Fatigue Crack Initiation ◽  
Three Dimensional ◽  
Finite Element Analyses ◽  
Mechanics Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In this paper, dynamic mechanics analysis was performed, in order to investigate the maximum forces acting on the crankshaft under working conditions. Then, three dimensional, finite element analyses have been conducted, in an attempt to predict the fatigue crack-initiation locations and lives. The maximum loadings, used in finite element analyses, were analytical obtained, which correspond to the five critical rotational angles of the first crankpin, i.e. = 40 º, 110º, 185 º, 255 º, 325 º. The maximum stress site was found to be approximately on the fillet of the first main journal of the crankshaft. The predicted fatigue life of the crankshafts was obtained by use of a stress-life (S-N) approach.

Three-Dimensional Finite Element Calculations of Thermal Stresses in Patterned GaAs / Si

1991 ◽  
Vol 239 ◽  
Author(s):  
E. H. Lingunis ◽  
N. M. Haegel ◽  
N. H. Karam
Keyword(s):  
Finite Element ◽  
Thermal Stresses ◽  
Stress Measurement ◽  
Three Dimensional ◽  
Biaxial Stress ◽  
Luminescence Spectra ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Free Edges

ABSTRACTThree-dimensional elastic finite element analysis was used to investigate the stress state in patterned GaAs/Si squares with different width to thickness ratios. Quantitative results for stress relief close to free edges were obtained. Features not revealed by previous two-dimensional calculations show the necessity of the three-dimensional treatment. For large areas the calculations give an approximately uniform biaxial stress everywhere, with reduced magnitude close to free edges. This allows for straightforward interpretation of high spatial resolution luminescence spectra and precise stress measurement. Experimental results from low temperature photoluminescence show good agreement with the calculated stresses. Finally, the effects of adjacent layers of different materials on the stress in epitaxial semiconductor thin films is investigated (particularly the case of InP/GaAs/Si) and discussed in conjunction with previous results.

Thermomechanical Stresses in Copper Interconnect/Low-κ Dielectric Systems

2004 ◽  
Vol 812 ◽  
Author(s):  
Y.-L. Shen ◽  
E. S. Ege
Keyword(s):  
Finite Element ◽  
Metal Oxide ◽  
Numerical Simulations ◽  
Thermal Stresses ◽  
Three Dimensional ◽  
Deformation Pattern ◽  
Barrier Layers ◽  
Copper Interconnect ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

AbstractNumerical simulations of thermal stresses in copper interconnect and low-κ dielectric systems are carried out. The analyses include two- and three-dimensional finite element modeling of the interconnect structure. Various combinations of metal, oxide and polymer-based low-κ dielectric schemes are considered in the simulation. The evolution of stresses and deformation pattern in copper, barrier layers, and the dielectrics are critically assessed.

Effects of Local Interfacial Debonding on the Stress Evolution in Aluminum Interconnects

1997 ◽  
Vol 473 ◽  
Author(s):  
Y. -L. Shen
Keyword(s):  
Thermal Stresses ◽  
Three Dimensional ◽  
Interfacial Debonding ◽  
Stress Fields ◽  
Stress Evolution ◽  
Geometrical Features ◽  
Dimensional Finite Element ◽  
Interconnect Reliability ◽  
Three Dimensional Finite Element ◽  
Aluminum Interconnects

ABSTRACTThe evolution of thermal stresses in aluminum interconnects, with the presence of local debonded areas between the aluminum line and the surrounding dielectric, is studied numerically. Local interfacial debonding is presumably due to contamination during the line patterning process. Various geometrical features of the interconnect and the debond segment are assumed, and the resulting stress fields are examined by recourse to two- and three-dimensional finite element analyses. Implications of the findings to the interconnect reliability, particularly stress-induced voiding in aluminum lines, are discussed.

Sign in / Sign up

Export Citation Format

Share Document