Effect of Void Fraction on Vibrational Behavior of Tubes in Tube Bundle Under Two-Phase Cross Flow

1997 ◽  
Vol 119 (3) ◽  
pp. 457-463 ◽  
Author(s):  
H. Y. Lian ◽  
G. Noghrehkar ◽  
A. M. C. Chan ◽  
M. Kawaji
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Tube Bundle ◽  
Dynamic Pressure ◽  
Damping Ratio ◽  
Cross Flow ◽  
Vibration Measurement ◽  
Phase Flow ◽  
Two Phase ◽  
Vibrational Behavior

The effects of local two-phase flow parameters on the vibrational behavior of tubes have been studied in an in-line 5 × 20 tube bundle subjected to air-water cross-flow. One of the tubes was flexibly mounted and instrumented for vibration measurement and the others were rigid. Parameters obtained include local void fraction fluctuations, RMS amplitude of void fraction fluctuations, void fraction distributions across the tube bundle, flow regimes based on probability density function of void fraction signals, damping ratio, and tube vibration response as a function of mass flux, void fraction and dynamic pressure. Damping and tube vibration amplitude in two-phase flow have been found to be closely related to the RMS amplitudes of the local void fraction fluctuations and dynamic pressure fluctuations, respectively.

scholarly journals On Damping and Fluidelastic Instability in a Tube Bundle Subjected to Two-Phase Cross-Flow

2007 ◽  
Author(s):  
Joaquin E. Moran ◽  
David S. Weaver
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Tube Bundle ◽  
Damping Ratio ◽  
Pressure Fluctuations ◽  
Cross Flow ◽  
Phase Changes ◽  
Working Fluid ◽  
Two Phase ◽  
Fluidelastic Instability

An experimental study was conducted to investigate damping and fluidelastic instability in tube arrays subjected to two-phase cross-flow. The purpose of this research was to improve our understanding of these phenomena and how they are affected by void fraction and flow regime. The working fluid used was Freon 11, which better models steam-water than air-water mixtures in terms of vapour-liquid mass ratio as well as permitting phase changes due to pressure fluctuations. The damping measurements were obtained by “plucking” the monitored tube from outside the test section using electromagnets. An exponential function was fitted to the tube decay trace, producing consistent damping measurements and minimizing the effect of frequency shifting due to fluid added mass fluctuations. The void fraction was measured using a gamma densitometer, introducing an improvement over the Homogeneous Equilibrium Model (HEM) in terms of density and velocity predictions. It was found that the Capillary number, when combined with the two-phase damping ratio (interfacial damping), shows a well defined behaviour depending on the flow regime. This observation can be used to develop a better methodology to normalize damping results. The fluidelastic results agree with previously presented data when analyzed using the HEM and the half-power bandwidth method. The interfacial velocity is suggested for fluidelastic studies due to its capability for collapsing the fluidelastic data. The interfacial damping was introduced as a tool to include the effects of flow regime into the stability maps.

Fluidelastic Instability and Periodic Fluid Forces in a Normal Triangular Tube Bundle Subjected to Air-Water Flow

2010 ◽  
Author(s):  
G. Ricciardi ◽  
M. J. Pettigrew ◽  
N. W. Mureithi
Keyword(s):  
Two Phase Flow ◽  
Tube Bundle ◽  
Fatigue Cracks ◽  
Cross Flow ◽  
Fretting Wear ◽  
Phase Flow ◽  
Steam Generators ◽  
Two Phase ◽  
Fluid Forces ◽  
Void Fractions

Two-phase flow in power plant steam generators can induce tube vibrations, which may cause fretting-wear and even fatigue cracks. It is therefore important to understand the relevant two-phase flow-induced vibration mechanisms. Fluidelastic instabilities in cross-flow are known to cause the most severe vibration response in the U-bend region of steam generators. This paper presents test results of the vibration of a normal triangular tube bundle subjected to air-water cross-flow. The test section presents 31 flexible tubes. The pitch-to-diameter ratio of the bundle is 1.5, and the tube diameter is 38 mm. Tubes were flexible in the lift direction. Seven tubes were instrumented with strain gauges to measure their displacements. A broad range of void fractions (from 10% to 90%) and fluid velocities (up to 13 m/s) were tested. Fluidelastic instabilities were observed for void fractions between 10% and 60%. Periodic fluid forces were also observed. The results are compared with those obtained with the rotated triangular tube bundle, showing that the normal triangular configuration is more stable than the rotated triangular configuration.

Flow-Induced Vibration Responses of U-Tube Bundle in Air-Water Flow

2007 ◽  
Author(s):  
In-Cheol Chu ◽  
Heung June Chung ◽  
Chang Hee Lee ◽  
Hyung Hyun Byun ◽  
Moo Yong Kim
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Tube Bundle ◽  
Damping Ratio ◽  
Geometrical Parameters ◽  
Phase Flow ◽  
Elastic Instability ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Vibration Responses

In the present study, a series of experiments have been performed to investigate a fluid-elastic instability of a nuclear steam generator U-tube bundle in an air-water two-phase flow condition. A total of 39 U-tubes are arranged in a rotated square array with a pitch-to-diameter ratio of 1.633. The diameter and other geometrical parameters of U-bend region are the same to those of an actual steam generator, but the vertical length of U-tubes are reduced to 2-span in contrast to 9-span of an actual steam generator. The following parameters were experimentally measured to evaluate a fluid-elastic instability of U-tube bundles in a two-phase flow: a general tube vibration response, a critical gap velocity, a damping ratio and a hydrodynamic mass. Based on the experimental measurements, the instability factor, K, of Connors’ relation was preliminary assessed with some assumptions on the velocity and density profiles of the two-phase flow.

scholarly journals A New Capacitance Sensor for Measuring the Void Fraction of Two-Phase Flow Through Tube Bundles

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2088
Author(s):  
Wael Ahmed ◽  
Adib Fatayerji ◽  
Ahmed Elsaftawy ◽  
Marwan Hassan ◽  
David Weaver ◽  
...  
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Tube Bundle ◽  
Local Variation ◽  
Phase Flow ◽  
Capacitance Sensor ◽  
Two Phase ◽  
Element Analysis ◽  
Tube Bundles ◽  
The Stability

Evaluating the two-phase flow parameters across tube bundles is crucial to the analysis of vibration excitation mechanisms. These parameters include the temporal and local variation of void fraction and phase redistribution. Understanding these two-phase parameters is essential to evaluating the stability threshold of tube bundle configurations. In this work, capacitance sensor probes were designed using finite element analysis to ensure high sensor sensitivity and optimum response. A simulation-based approach was used to calibrate and increase the accuracy of the void fraction measurement. The simulation results were used to scale the normalized capacitance and minimize the sensor uncertainty to ±5%. The sensor and required conditioning circuits were fabricated and tested for measuring the instantaneous void fraction in a horizontal triangular tube bundle array under both static and dynamic two-phase flow conditions. The static calibration of the sensor was able to reduce the uncertainty to ±3% while the sensor conditioning circuit was able to capture instantaneous void fraction signals with frequencies up to 2.5 kHz.

Vibration of a Tube Bundle in Two-Phase Freon Cross-Flow

1995 ◽  
Vol 117 (4) ◽  
pp. 321-329 ◽  
Author(s):  
M. J. Pettigrew ◽  
C. E. Taylor ◽  
J. H. Jong ◽  
I. G. Currie
Keyword(s):  
Two Phase Flow ◽  
Tube Bundle ◽  
Density Ratio ◽  
Cross Flow ◽  
Flow Regimes ◽  
Phase Flow ◽  
Two Phase ◽  
Void Fractions ◽  
Fluidelastic Instability ◽  
First Results

Two-phase cross-flow exists in many shell-and-tube heat exchangers. The U-bend region of nuclear steam generators is a prime example. Testing in two-phase flow simulated by air-water provides useful results inexpensively. However, two-phase flow parameters, in particular surface tension and density ratio, are considerably different in air-water than in steam-water. A reasonable compromise is testing in liquid-vapor Freon, which is much closer to steam-water while much simpler experimentally. This paper presents the first results of a series of tests on the vibration behavior of tube bundles subjected to two-phase Freon cross-flow. A rotated triangular tube bundle of tube-to-diameter ratio of 1.5 was tested over a broad range of void fractions and mass fluxes. Fluidelastic instability, random turbulence excitation, and damping were investigated. Well-defined fluidelastic instabilities were observed in continuous two-phase flow regimes. However, intermittent two-phase flow regimes had a dramatic effect on fluidelastic instability. Generally, random turbulence excitation forces are much lower in Freon than in air-water. Damping is very dependent on void fraction, as expected.

Primitive Model for the Random Excitation of a Tube Under Two-Phase Cross Flow

2016 ◽  
Author(s):  
Laurent Borsoi ◽  
Philippe Piteau ◽  
Xavier Delaune ◽  
Jose Antunes
Keyword(s):  
Two Phase Flow ◽  
Tube Bundle ◽  
Cross Flow ◽  
Interface Velocity ◽  
Momentum Conservation ◽  
Random Excitation ◽  
Nuclear Industry ◽  
Phase Flow ◽  
Two Phase ◽  
Primitive Model

Flow-induced vibration of heat-exchangers tubes is particularly studied in the nuclear industry for safety and cost reasons. It implies to have, among others, relevant characterizations of the random buffeting forces the cross-flow applies to the tube bundle. Work is still needed in this domain, particularly for two-phase flow, to improve the available data as the ones for PWR steam generator, currently very envelope. In parallel to get new experimental data, using “real” or substitutional mixtures (e.g. air-water instead of steam-water for PWR), it is essential to understand the basic excitation mechanisms which induce the vibrations under two-phase flow, as e.g. the influence of flow regimes. In this general framework, what can be learnt from deliberately simple models may be a contributive help. As a first attempt on this issue, the paper deals with the elementary case of a single rigid tube under air-water cross flow. This case is part of experiments carried out at CEA-Saclay with bundles where both tube support reactions and flow characteristics are measured, with respectively piezo-electrical sensors and bi-optical probes (BOP). The information provided by the BOP (mean interface velocity, statistical distribution, etc.) feeds a primitive model of water “droplet” impulses on the tube, based on a lot of crude assumptions about impact velocity, momentum conservation, impulse shape, statistical independence, etc., and which uses analytical results of random processes constructed from the superposition of random pulses. The “equivalent” excitation force, obtained in terms of dimensional PSD, is compared to the one measured in the drag and lift direction with an acceptable agreement, at least in order of magnitude. Comments and lessons are drawn from this first attempt, and some paths are advanced to improve this kind of primitive models, especially for treating rigid square bundles under air-water cross flow.

On the Damping in Tube Arrays Subjected to Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
J. E. Moran ◽  
D. S. Weaver
Keyword(s):  
Flow Regime ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Cross Flow ◽  
Working Fluid ◽  
Exponential Fitting ◽  
Phase Flow ◽  
Two Phase ◽  
Tube Arrays ◽  
Half Power

An experimental study was conducted to investigate the mechanism of damping in tube arrays subjected to two-phase cross-flow, mainly focusing on the influence of void fraction and flow regime. The model tube bundle had a parallel-triangular configuration, with a pitch ratio of 1.49. The two-phase flow loop used in this research utilized Refrigerant 11 as the working fluid, which better models steam-water than air-water mixtures in terms of vapour-liquid mass ratio as well as permitting phase changes due to pressure fluctuations. The void fraction was measured using a gamma densitometer, introducing an improvement over the homogeneous equilibrium model (HEM). Three different damping measurement methodologies were implemented and compared in order to obtain a more reliable damping estimate: the traditionally used half-power bandwidth, the logarithmic decrement and an exponential fitting to the tube decay response. The experiments showed that the half-power bandwidth produces higher damping values than the other two methods, due to the tube frequency shifting triggered by fluctuations in the added mass and coupling between the tubes, which depend on void fraction and flow regime. The exponential fitting proved to be the more consistent and reliable approach to estimating damping. A dimensional analysis was carried out to investigate the relationship between damping and two-phase flow related parameters. As a result, the inclusion of surface tension in the form of the capillary number appears to be useful when combined with the two-phase component of the damping ratio (interfacial damping). A strong dependence of damping on flow regime was observed when plotting the interfacial damping versus the void fraction, introducing an improvement over the previous results obtained by normalizing the two-phase damping, which does not exhibit this behavior.

Sign in / Sign up

Export Citation Format

Share Document