Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part II—Unsteady Measurements

1997 ◽  
Vol 119 (3) ◽  
pp. 655-662 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack
Keyword(s):  
Velocity Field ◽  
Turbine Blades ◽  
Angular Position ◽  
Torque Converter ◽  
Speed Ratio ◽  
Velocity Data ◽  
Velocity Fluctuations ◽  
Blade Passage ◽  
Turbine Pump ◽  
Output Torque

The unsteady velocity field found in the turbine of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, quarter, mild, and exit planes of the turbine were investigated at two significantly different turbine/pump rotational speed ratios: 0.065 and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data are assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the velocity data, visualizing the transient interaction effects between the turbine, pump, and stator was possible. Results showed strong cyclic velocity fluctuations in the turbine inlet plane as a function of the relative turbine-pump position. These fluctuations are due to the passing of upstream pump blades by the slower rotating turbine blades. Typical fluctuations in the through flow velocity were 3.6 m/s. Quarter and midplane velocity fluctuations were seen to be lower; typical values were 1.5 m/s and 0.8 m/s, respectively. The flow field in the turbine exit plane was seen to be relatively steady with negligible fluctuations of less than 0.03 m/s. From the velocity data, the fluctuations of turbine performance parameters such as flow inlet angles, root-mean-square unsteadiness, and output torque per blade passage were calculated. Incidence angles were seen to vary by 3 and 6 deg for the 0.800 and 0.065 speed ratios, respectively, while the exit angles remained steady. The turbine output torque per blade passage fluctuated by 0.05 Nm for the 0.800 speed ratio and 0.13 Nm for the 0.065 speed ratio.

Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part II — Unsteady Measurements

1995 ◽  
Author(s):  
Klaus Bran ◽  
Ronald D. Flack
Keyword(s):  
Velocity Field ◽  
Angular Position ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Velocity Data ◽  
Velocity Fluctuations ◽  
Blade Passage ◽  
Turbine Pump ◽  
Output Torque

The unsteady velocity field found in the turbine of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, quarter, mid, and exit planes of the turbine were investigated at two significantly different operating conditions: turbine/pump rotational speed ratios of 0.065, and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data is assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the velocity data, visualizing the transient interaction effects between the turbine, pump, and stator was possible. Results showed strong cyclic velocity fluctuations in the turbine inlet plane as a function of the relative turbine-pump position. These fluctuations are due to the passing of upstream pump blades by the slower rotating turbine blades. Typical fluctuations in the through flow velocity were 3.6 m/s. Quarter and mid plane velocity fluctuations were seen to be lower; typical values were 1.5 m/s and 0.8 m/s, respectively. The flow field in the turbine exit plane was seen to be relatively steady with negligible fluctuations of less than 0.03 m/s. From the velocity data, the fluctuations of turbine performance parameters such as flow inlet angles, root-mean-square unsteadiness, and output torque per blade passage were calculated. Incidence angles were seen to vary by 3° and 6° for the 0.800 and 0.065 speed ratios, respectively, while the exit angles remained steady. The turbine output torque per blade passage fluctuated by 0.05 Nm for the 0.800 speed ratio and 0.13 Nm for the 0.065 speed ratio.

Experimental Investigation on Cavitation Performance of Torque Converter Using Transparent Model

2019 ◽  
Author(s):  
Yusuke Katayama ◽  
Yuki Hosoi ◽  
Yuta Fukuda ◽  
Satoshi Watanabe ◽  
Shin-ichi Tsuda ◽  
...  
Keyword(s):  
High Speed ◽  
Turbine Blades ◽  
Suction Side ◽  
Torque Converter ◽  
Working Fluid ◽  
Speed Ratio ◽  
Cavitation Phenomenon ◽  
Cavitation Bubbles ◽  
Charge Pressure ◽  
Dissolved Air

Abstract In this study, we experimentally investigated the influence of the amount of dissolved air in working fluid and the rotation speed ratio of turbine to pump elements on cavitation phenomenon in automotive torque converter. In order to directly observe the cavitation phenomenon, transparent model was used. The applied charge pressure was varied to change the significance of cavitation. The pump and turbine torques were simultaneously measured to clarify the relation between torque performance and cavitation phenomenon. As a result, the cavitation region was found to depend on the speed ratio; cavitation occurred on the suction side of turbine blades at low speed ratios while in the pump region at high speed ratios. The effect of the amount of dissolved air was significant, which enhanced the growth of cavitation bubbles through the deposition of dissolved air. In such cases, with the further decrease of charge pressure, a large number of gaseous cavitation bubbles appeared in the whole flow passage. The torque performance was deteriorated at this stage.

scholarly journals Measurements of Strain on 310 mm Torque Converter Turbine Blades

2004 ◽  
Vol 10 (1) ◽  
pp. 55-63
Author(s):  
P. O. Sweger ◽  
C. L. Anderson ◽  
J. R. Blough
Keyword(s):  
Turbine Blade ◽  
Turbine Blades ◽  
Torque Converter ◽  
Operating Conditions ◽  
Surface Strain ◽  
Speed Ratio ◽  
Constant Input ◽  
Wide Range ◽  
Blade Tip ◽  
Input Torque

An automotive torque converter was tested in order to determine the effect of converter operating condition and turbine blade design on turbine blade strain in the region of the inlet core tab restraint. The converter was operated over a wide range of speed ratios (0 to 0.95) at constant input torque and a stall condition for two input torques. Foil-type strain gages in combination with wireless microwave telemetry were used to measure surface strain on the turbine blade. Strain measurements were made on two turbine blade designs.The steady component of strain over the range of speed ratios suggests the effect of both torque loading and centrifugal loading on the turbine blade tip. The unsteady strain was greatest at stall condition and diminished as speed ratio increased. Greater input torque at stall condition resulted in both greater steady strain and greater unsteady strain. The spectral distribution of strain over the range of tested speed ratios displayed an increase in low-frequency broadband fluctuations near stall condition. A blade-periodic event is observed which correlates to the pump-blade passing frequency relative to the turbine rotating frame. Reducing the blade-tip surface area and increasing the inlet-tab root radius reduced the range of steady strain and magnitude of unsteady strain imposed near the inlet core tab restraint over the range of operating conditions.

Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter: Part II—Unsteady Measurements

1996 ◽  
Vol 118 (3) ◽  
pp. 570-577 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack ◽  
J. K. Gruver
Keyword(s):  
Velocity Field ◽  
Flow Field ◽  
Incidence Angle ◽  
Angular Position ◽  
Three Dimensional ◽  
Torque Converter ◽  
Operating Conditions ◽  
Plane Flow ◽  
Periodic Fluctuations ◽  
Pump Inlet

The unsteady velocity field found in the pump of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, mid-, and exit planes of the pump were investigated at two significantly different operating conditions: turbine/pump rotational speed ratios of 0.065 and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data are assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the data, visualizing the transient interaction effects between the stator and the pump, and between the pump and the turbine, was possible. Results showed strong cyclic velocity fluctuations in the pump inlet plane as a function of the relative stator-pump position. Typical percent periodic fluctuations in the through flow velocity were 70 percent of the average throughflow velocity. The upstream propagation influence of the turbine on the pump exit plane flow field was seen to be smaller. Percent periodic fluctuations of the throughflow velocity were typically 30 percent. The effect of the stator and turbine on the midplane flow field was seen to be negligible. The incidence angle at the pump inlet fluctuated by 27 and 14 deg for the 0.065 and 0.800 speed ratios, respectively. Typical slip factors at the exit were 0.965 and fluctuated by less than 1 percent.

Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter: Part I—Average Measurements

1996 ◽  
Vol 118 (3) ◽  
pp. 562-569 ◽  
Author(s):  
J. K. Gruver ◽  
R. D. Flack ◽  
K. Brun
Keyword(s):  
Angular Position ◽  
Torque Converter ◽  
Secondary Flows ◽  
Speed Ratio ◽  
Exit Plane ◽  
Centrifugal Pumps ◽  
Torque Distribution ◽  
Average Flow Velocity ◽  
Pump Shaft ◽  
Pump Inlet

A torque converter was tested for two turbine/pump rotational speed ratios, 0.065 and 0.800, and a laser velocimeter was used to measure three components of velocity within the pump. Shaft encoders were used to record the instantaneous pump angular position, which was correlated with the velocities. Average flow velocity profiles were obtained for the pump inlet, mid-, and exit planes. Large separation regions were seen in the mid- and exit planes of the pump for a speed ratio of 0.800. Strong counterclockwise secondary flows were observed in the midplane and strong clockwise secondary flows were seen in the exit plane of the pump for all conditions; vorticities were evaluated and are reported. Velocity data were also used to find the torque distribution. For both speed ratios the torque was approximately evenly distributed between the inlet and exit. Finally, slip factors were evaluated at the mid-and exit planes. At the midplane they were approximately the same as for conventional centrifugal pumps; however, at the exit plane the slip factors are larger than for centrifugal pumps.

On the Use of Velocity Data for Load Estimation of a VAWT in Dynamic Stall

2011 ◽  
Vol 133 (1) ◽  
Author(s):  
Carlos J. Simão Ferreira ◽  
Gerard J. W. van Bussel ◽  
Gijs A. M. van Kuik ◽  
Fulvio Scarano
Keyword(s):  
Velocity Field ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Pressure Sensors ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Velocity Data ◽  
Vertical Axis Wind Turbine ◽  
Wind Turbine Blades ◽  
Image Velocimetry

This paper focuses on evaluating the feasibility of estimating loads on vertical axis wind turbine blades in dynamic stall with velocity data acquired with Particle Image Velocimetry. The study uses numerical simulation data of a 2D Vertical Axis Wind Turbine in dynamic stall to verify sources of error and uncertainty and estimate the accuracy of the method. The integration of the forces from the velocity field overcomes the difficulties and limitations presented by pressure sensors for estimating the local section loads, but adds the difficulty in determining the correct velocity field and its time and spatial derivatives. The analysis also evaluates the use of phase-locked average data as an estimator of average loads.

scholarly journals Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter Part I – Effect of Speed Ratio

2000 ◽  
Vol 6 (3) ◽  
pp. 167-180 ◽  
Author(s):  
Steven B. Ainley ◽  
Ronald D. Flack ◽  
Klaus Brun ◽  
Tony J. Rovello
Keyword(s):  
Flow Field ◽  
Rotational Speed ◽  
Angular Position ◽  
Torque Converter ◽  
Speed Ratio ◽  
Exit Plane ◽  
Centrifugal Pumps ◽  
Plane Flow ◽  
Shaft Encoder ◽  
Mass Flows

A torque converter was tested at four turbine/pump rotational speed ratios (0.200, 0.400, 0.600, and 0.800) all with a constant pump rotational speed in order to determine the effect of speed ratio on the torque converter pump flow field. Laser velocimetry was used to measure three components of velocity within the pump and a shaft encoder was employed to record the instantaneous pump angular position. Shaft encoder information was correlated with measured velocities to develop flow field blade-to-blade profiles and vector plots. Measurements were obtained in both the pump mid- and exit planes for all four speed ratios. Results showed large separation regions and jet/wake flows throughout the pump. The midplane flow was found to have strong counter-clockwise secondary components and the exit plane flow had strong clockwise secondary components. Mass flows were calculated from the velocity data and were found to decrease as the speed ratio was increased. Also, the vorticity and slip factors were calculated from the experimental data and are included. The mid-plane slip factors compare favorably to those for conventional centrifugal pumps but less slip was present in the exit plane than the mid-plane. Neither the slip factor nor the vorticity were seen to be strongly affected by the speed ratio. Finally, the torque core-to-shell and blade-to-blade torque distributions are presented for both planes.

scholarly journals Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter: Part II — Unsteady Measurements

1994 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack ◽  
J. K. Gruver
Keyword(s):  
Velocity Field ◽  
Flow Field ◽  
Flow Velocity ◽  
Angular Position ◽  
Torque Converter ◽  
Operating Conditions ◽  
Plane Flow ◽  
Through Flow ◽  
Periodic Fluctuations ◽  
Pump Inlet

The unsteady velocity field found in the pump of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, mid-, and exit planes of the pump were investigated at two significantly different operating conditions: turbine/pump rotational speed ratios of 0.065, and 0.800. A data organization method was developed to visualize the three dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data is assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the data visualizing the transient interaction effects between the stator and the pump, and the pump and the turbine was possible. Results showed strong cyclic velocity fluctuations in the pump inlet plane as a function of the relative stator-pump position. Typical percent periodic fluctuations in the through flow velocity were 70% of the average through flow velocity. The upstream propagation influence of the turbine on the pump exit plane flow field was seen to he smaller. Percent periodic fluctuations of the through flow velocity were typically 30%. The effect of the stator and turbine on the mid-plane flow field was seen to be negligible. The incidence angle at the pump inlet fluctuated by 27° and 14° for the 0.065 and 0.800 speed ratios, respectively. Typical slip factors at the exit were 0.965 and fluctuated by less than 1%.

scholarly journals Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part I — Average Measurements

1995 ◽  
Author(s):  
Klaus Bran ◽  
Ronald D. Flack
Keyword(s):  
Velocity Vector ◽  
Average Velocity ◽  
Incidence Angle ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Flow Angle ◽  
Pump Speed ◽  
Turbine Pump ◽  
Mass Flows

The three-dimensional average velocity field in an automotive torque converter turbine was examined. Two significantly different operating conditions of the torque converter were tested: the 0.065 and 0.800 turbine/pump speed ratio. Velocities were measured using a one-directional, frequency shifted laser velocimeter. The instantaneous angular positions of the torque converter turbine and pump were recorded using digital shaft encoders. Shaft encoder information and velocities were correlated to generate average velocity blade-to-blade profiles and velocity vector plots. Measurements were taken in the inlet, quarter, mid, and exit planes of the turbine. From the experimental velocity measurements, mass flows, turbine output torque, average vorticities, viscous dissipation, inlet incidence flow angles, and exit flow angles were calculated. Average mass flows were 23.4 kg/s and 14.7 kg/s for the 0.065 and 0.800 speed ratios, respectively. Velocity vector plots for both turbine/pump speed ratios showed the flow field in the turbine quarter and mid planes to be highly non-uniform with separation regions and reversed flows at the core-suction corner. For the conditions tested, the turbine inlet flow was seen to have a high relative incidence angle, while the relative turbine exit flow angle was close to the blade angle.

Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part I—Average Measurements

1997 ◽  
Vol 119 (3) ◽  
pp. 646-654 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack
Keyword(s):  
Velocity Vector ◽  
Average Velocity ◽  
Incidence Angle ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Flow Angle ◽  
Pump Speed ◽  
Turbine Pump ◽  
Mass Flows

The three-dimensional average velocity field in an automotive torque converter turbine was examined. Two significantly different operating conditions of the torque converter were tested: the 0.065 and 0.800 turbine/pump speed ratio. Velocities were measured using a one-directional, frequency-shifted laser velocimeter. The instantaneous angular positions of the torque converter turbine and pump were recorded using digital shaft encoders. Shaft encoder information and velocities were correlated to generate average velocity blade-to-blade profiles and velocity vector plots. Measurements were taken in the inlet, quarter, mid, and exit planes of the turbine. From the experimental velocity measurements, mass flows, turbine output torque, average vorticities, viscous dissipation, inlet incidence flow angles, and exit flow angles were calculated. Average mass flows were 23.4 kg/s and 14.7 kg/s for the 0.065 and 0.800 speed ratios, respectively. Velocity vector plots for both turbine/pump speed ratios showed the flow field in the turbine quarter and midplanes to be highly nonuniform with separation regions and reversed flows at the core-suction corner. For the conditions tested, the turbine inlet flow was seen to have a high relative incidence angle, while the relative turbine exit flow angle was close to the blade angle.

Sign in / Sign up

Export Citation Format

Share Document