Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part I—Average Measurements

1997 ◽  
Vol 119 (3) ◽  
pp. 646-654 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack
Keyword(s):  
Velocity Vector ◽  
Average Velocity ◽  
Incidence Angle ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Flow Angle ◽  
Pump Speed ◽  
Turbine Pump ◽  
Mass Flows

The three-dimensional average velocity field in an automotive torque converter turbine was examined. Two significantly different operating conditions of the torque converter were tested: the 0.065 and 0.800 turbine/pump speed ratio. Velocities were measured using a one-directional, frequency-shifted laser velocimeter. The instantaneous angular positions of the torque converter turbine and pump were recorded using digital shaft encoders. Shaft encoder information and velocities were correlated to generate average velocity blade-to-blade profiles and velocity vector plots. Measurements were taken in the inlet, quarter, mid, and exit planes of the turbine. From the experimental velocity measurements, mass flows, turbine output torque, average vorticities, viscous dissipation, inlet incidence flow angles, and exit flow angles were calculated. Average mass flows were 23.4 kg/s and 14.7 kg/s for the 0.065 and 0.800 speed ratios, respectively. Velocity vector plots for both turbine/pump speed ratios showed the flow field in the turbine quarter and midplanes to be highly nonuniform with separation regions and reversed flows at the core-suction corner. For the conditions tested, the turbine inlet flow was seen to have a high relative incidence angle, while the relative turbine exit flow angle was close to the blade angle.

scholarly journals Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part I — Average Measurements

1995 ◽  
Author(s):  
Klaus Bran ◽  
Ronald D. Flack
Keyword(s):  
Velocity Vector ◽  
Average Velocity ◽  
Incidence Angle ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Flow Angle ◽  
Pump Speed ◽  
Turbine Pump ◽  
Mass Flows

The three-dimensional average velocity field in an automotive torque converter turbine was examined. Two significantly different operating conditions of the torque converter were tested: the 0.065 and 0.800 turbine/pump speed ratio. Velocities were measured using a one-directional, frequency shifted laser velocimeter. The instantaneous angular positions of the torque converter turbine and pump were recorded using digital shaft encoders. Shaft encoder information and velocities were correlated to generate average velocity blade-to-blade profiles and velocity vector plots. Measurements were taken in the inlet, quarter, mid, and exit planes of the turbine. From the experimental velocity measurements, mass flows, turbine output torque, average vorticities, viscous dissipation, inlet incidence flow angles, and exit flow angles were calculated. Average mass flows were 23.4 kg/s and 14.7 kg/s for the 0.065 and 0.800 speed ratios, respectively. Velocity vector plots for both turbine/pump speed ratios showed the flow field in the turbine quarter and mid planes to be highly non-uniform with separation regions and reversed flows at the core-suction corner. For the conditions tested, the turbine inlet flow was seen to have a high relative incidence angle, while the relative turbine exit flow angle was close to the blade angle.

scholarly journals Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter Part II – Effect of Pump Speed and Oil Viscosity

2000 ◽  
Vol 6 (3) ◽  
pp. 181-190 ◽  
Author(s):  
Ronald D. Flack ◽  
Steven B. Ainley ◽  
Klaus Brun ◽  
Leonard Whitehead
Keyword(s):  
Rotational Speed ◽  
Three Dimensional ◽  
Torque Converter ◽  
Secondary Flows ◽  
Working Fluid ◽  
Speed Ratio ◽  
Oil Viscosity ◽  
Low Velocity ◽  
Pump Speed ◽  
Mass Flows

The velocity field inside a torque converter pump was studied for two separate effects: variable pump rotational speed and variable oil viscosity. Three-dimensional velocity measurements were taken using a laser velocimeter for both the pump mid- and exit planes. The effect ofvariable pump rotational speed was studied by running the pump at two different speeds and holding speed ratio (pump rotational speed]turbine rotational speed) constant. Similarly, the effect of viscosity on the pump flow field was studied by varying the temperature and]or using two different viscosity oils as the working fluid in the pump. Threedimensional velocity vector plots, through-flow contour plots, and secondary flow profiles were obtained for both pump planes and all test conditions. Results showed that torque converter mass flows increased approximately linearly with increasing pump rotational speed (and fixed speed ratio) but that the flow was not directly proportional to pump rotational speed. However, mass flows were seen to decrease as the oil viscosity was decreased with a resulting increased Reynolds number; for these conditions the high velocity regions were seen to decrease in size and low velocity regions were seen to increase in size. In the pump mid-plane strong counter-clockwise secondary flows and in the exit plane strong clockwise secondary flows were observed. The vorticities and slip factors were calculated from the experimental results and are presented. The torque core-to-shell and blade-to-blade torque distributions were calculated for both planes. Finally, the flow fields were seen to demonstrate similitude when Reynolds numbers were matched.

Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part II — Unsteady Measurements

1995 ◽  
Author(s):  
Klaus Bran ◽  
Ronald D. Flack
Keyword(s):  
Velocity Field ◽  
Angular Position ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Velocity Data ◽  
Velocity Fluctuations ◽  
Blade Passage ◽  
Turbine Pump ◽  
Output Torque

The unsteady velocity field found in the turbine of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, quarter, mid, and exit planes of the turbine were investigated at two significantly different operating conditions: turbine/pump rotational speed ratios of 0.065, and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data is assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the velocity data, visualizing the transient interaction effects between the turbine, pump, and stator was possible. Results showed strong cyclic velocity fluctuations in the turbine inlet plane as a function of the relative turbine-pump position. These fluctuations are due to the passing of upstream pump blades by the slower rotating turbine blades. Typical fluctuations in the through flow velocity were 3.6 m/s. Quarter and mid plane velocity fluctuations were seen to be lower; typical values were 1.5 m/s and 0.8 m/s, respectively. The flow field in the turbine exit plane was seen to be relatively steady with negligible fluctuations of less than 0.03 m/s. From the velocity data, the fluctuations of turbine performance parameters such as flow inlet angles, root-mean-square unsteadiness, and output torque per blade passage were calculated. Incidence angles were seen to vary by 3° and 6° for the 0.800 and 0.065 speed ratios, respectively, while the exit angles remained steady. The turbine output torque per blade passage fluctuated by 0.05 Nm for the 0.800 speed ratio and 0.13 Nm for the 0.065 speed ratio.

Flow Pattern Evolution and Energy Decomposition of Flows at Different Operating Conditions in a Hydrodynamic Torque Converter

2016 ◽  
Author(s):  
Wei Wei ◽  
Mingxing Huang ◽  
Yu Li ◽  
Qingdong Yan
Keyword(s):  
Vortex Structure ◽  
Velocity Vector ◽  
Power Transmission ◽  
Flow Behavior ◽  
Internal Flow ◽  
Torque Converter ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Energy Decomposition ◽  
Complex Flow

Power loss and flow blockage in turbomachinery such as hydrodynamic torque converter are usually caused by jet flow, second flow and flow separation. In this paper, the velocity vector and the pressure distribution of the internal flow field in hydrodynamic torque converter were reduced by the method of the Proper Orthogonal Decomposition (POD) to find the main flow structures and the energy decomposition in the passages of pump, turbine and stator. In order to find their evolutionary processes and energy decompositions, oil flow visualizations were conducted at different speed ratios from 0 to 0.8, including stall condition and design operating condition. The results showed that the first few modes containing the majority of energy could provide enough accuracy to predict flow behavior and flow structure in flow passages. Especially when the energy percentage of the first mode was majority, its vortex structures could be recognized easily. But the flow patterns of other modes were different from each other and they made the flow more turbulent and complex, which increases the energy loss in the process of power transmission. Besides that, the change of pressure gradient had a direct influence to velocity vector. The results also indicated that the observed fluid pattern of vortex structure became extensive while the influence of secondary flow decreased in the flow passage of pump with the increase of speed ratio. But the situation is just reversed in turbine, that is, the vortex disappeared gradually and the irregular turbulent flow appeared as the increase of speed ratio. In stator, the vortex structure emerged gradually when the speed ratio increased. So the method of snapshots is a very useful way to analyze the complex flow flied in depth and to predict the trend of development.

Laser Velocimeter Measurements in the Turbine of an Automotive Torque Converter: Part II—Unsteady Measurements

1997 ◽  
Vol 119 (3) ◽  
pp. 655-662 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack
Keyword(s):  
Velocity Field ◽  
Turbine Blades ◽  
Angular Position ◽  
Torque Converter ◽  
Speed Ratio ◽  
Velocity Data ◽  
Velocity Fluctuations ◽  
Blade Passage ◽  
Turbine Pump ◽  
Output Torque

The unsteady velocity field found in the turbine of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, quarter, mild, and exit planes of the turbine were investigated at two significantly different turbine/pump rotational speed ratios: 0.065 and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data are assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the velocity data, visualizing the transient interaction effects between the turbine, pump, and stator was possible. Results showed strong cyclic velocity fluctuations in the turbine inlet plane as a function of the relative turbine-pump position. These fluctuations are due to the passing of upstream pump blades by the slower rotating turbine blades. Typical fluctuations in the through flow velocity were 3.6 m/s. Quarter and midplane velocity fluctuations were seen to be lower; typical values were 1.5 m/s and 0.8 m/s, respectively. The flow field in the turbine exit plane was seen to be relatively steady with negligible fluctuations of less than 0.03 m/s. From the velocity data, the fluctuations of turbine performance parameters such as flow inlet angles, root-mean-square unsteadiness, and output torque per blade passage were calculated. Incidence angles were seen to vary by 3 and 6 deg for the 0.800 and 0.065 speed ratios, respectively, while the exit angles remained steady. The turbine output torque per blade passage fluctuated by 0.05 Nm for the 0.800 speed ratio and 0.13 Nm for the 0.065 speed ratio.

scholarly journals Measurements of Strain on 310 mm Torque Converter Turbine Blades

2004 ◽  
Vol 10 (1) ◽  
pp. 55-63
Author(s):  
P. O. Sweger ◽  
C. L. Anderson ◽  
J. R. Blough
Keyword(s):  
Turbine Blade ◽  
Turbine Blades ◽  
Torque Converter ◽  
Operating Conditions ◽  
Surface Strain ◽  
Speed Ratio ◽  
Constant Input ◽  
Wide Range ◽  
Blade Tip ◽  
Input Torque

An automotive torque converter was tested in order to determine the effect of converter operating condition and turbine blade design on turbine blade strain in the region of the inlet core tab restraint. The converter was operated over a wide range of speed ratios (0 to 0.95) at constant input torque and a stall condition for two input torques. Foil-type strain gages in combination with wireless microwave telemetry were used to measure surface strain on the turbine blade. Strain measurements were made on two turbine blade designs.The steady component of strain over the range of speed ratios suggests the effect of both torque loading and centrifugal loading on the turbine blade tip. The unsteady strain was greatest at stall condition and diminished as speed ratio increased. Greater input torque at stall condition resulted in both greater steady strain and greater unsteady strain. The spectral distribution of strain over the range of tested speed ratios displayed an increase in low-frequency broadband fluctuations near stall condition. A blade-periodic event is observed which correlates to the pump-blade passing frequency relative to the turbine rotating frame. Reducing the blade-tip surface area and increasing the inlet-tab root radius reduced the range of steady strain and magnitude of unsteady strain imposed near the inlet core tab restraint over the range of operating conditions.

Laser Velocimeter Measurements in the Pump of an Automotive Torque Converter: Part II—Unsteady Measurements

1996 ◽  
Vol 118 (3) ◽  
pp. 570-577 ◽  
Author(s):  
K. Brun ◽  
R. D. Flack ◽  
J. K. Gruver
Keyword(s):  
Velocity Field ◽  
Flow Field ◽  
Incidence Angle ◽  
Angular Position ◽  
Three Dimensional ◽  
Torque Converter ◽  
Operating Conditions ◽  
Plane Flow ◽  
Periodic Fluctuations ◽  
Pump Inlet

The unsteady velocity field found in the pump of an automotive torque converter was measured using laser velocimetry. Velocities in the inlet, mid-, and exit planes of the pump were investigated at two significantly different operating conditions: turbine/pump rotational speed ratios of 0.065 and 0.800. A data organization method was developed to visualize the three-dimensional, periodic unsteady velocity field in the rotating frame. For this method, the acquired data are assumed to be periodic at synchronous and blade interaction frequencies. Two shaft encoders were employed to obtain the instantaneous angular position of the torque converter pump and turbine at the instant of laser velocimeter data acquisition. By proper “registration” of the data, visualizing the transient interaction effects between the stator and the pump, and between the pump and the turbine, was possible. Results showed strong cyclic velocity fluctuations in the pump inlet plane as a function of the relative stator-pump position. Typical percent periodic fluctuations in the through flow velocity were 70 percent of the average throughflow velocity. The upstream propagation influence of the turbine on the pump exit plane flow field was seen to be smaller. Percent periodic fluctuations of the throughflow velocity were typically 30 percent. The effect of the stator and turbine on the midplane flow field was seen to be negligible. The incidence angle at the pump inlet fluctuated by 27 and 14 deg for the 0.065 and 0.800 speed ratios, respectively. Typical slip factors at the exit were 0.965 and fluctuated by less than 1 percent.

Study of a Highly Loaded Centrifugal Compressor With Pipe Diffuser at Design and Off-Design Operating Conditions

2015 ◽  
Author(s):  
Ge Han ◽  
Xingen Lu ◽  
Yanfeng Zhang ◽  
Shengfeng Zhao ◽  
Junqiang Zhu
Keyword(s):  
Centrifugal Compressor ◽  
Flow Separation ◽  
Incidence Angle ◽  
Leading Edge ◽  
Performance Comparison ◽  
Operating Conditions ◽  
Flow Distortion ◽  
Flow Angle ◽  
Rotating Speed ◽  
Highly Loaded

This present work is aimed at providing detailed understanding of the flow mechanisms in a highly loaded centrifugal compressor with different diffusers. Performance comparison between compressor stages with pipe diffuser and its original wedge diffuser was conducted by a validated state-of-the-art multi-block flow solver at different rotating speeds. Stage with pipe diffuser achieved a better performance above 80% rotating speed but a worse performance at lower rotating speeds near surge, than that of stage with wedge diffuser. Four operating points including the design point were analyzed in detail. The inherent diffuser leading edge of pipe diffuser could alleviate the flow distortion upstream diffuser throat and created a better operating condition for the downstream diffusion, which reduced the possibility of flow separation in discrete passages at design rotating speed. At 60% rotating speed operating point, there was a misalignment between the leading edge absolute flow angle and the metal angle of diffuser, resulted in an acceleration near diffuser leading edge due to the large negative incidence angle. The sharp leading edge of pipe diffuser could largely accommodate this negative incidence as comparison of the round leading edge of wedge diffuser. As a result, the flow separation was depressed and a better performance was achieved in the pipe diffuser. At 60% rotating speed near surge, performance of the pipe diffuser dropped below wedge diffuser. Total pressure loss of pipe diffuser exceeded that of the wedge diffuser due to the larger friction loss near wall at throat and cone, meanwhile ineffective static pressure recovery for pipe diffuser was triggered by the strong boundary layer blockage in the front of pipe diffuser cone.

Influence of Stator Blade Geometry on Torque Converter Cavitation

2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Cheng Liu ◽  
Wei Wei ◽  
Qingdong Yan ◽  
Brian K. Weaver ◽  
Houston G. Wood
Keyword(s):  
High Speed ◽  
Torque Converter ◽  
Operating Conditions ◽  
Hydrodynamic Performance ◽  
Speed Ratio ◽  
Capacity Loss ◽  
Wide Range ◽  
Stator Blade ◽  
Torque Converters ◽  
Blade Geometry

Cavitation in torque converters may cause degradation in hydrodynamic performance, severe noise, or even blade damage. Researches have highlighted that the stator is most susceptible to the occurrence of cavitation due to the combination of high flow velocities and high incidence angles. The objective of this study is to therefore investigate the effects of cavitation on hydrodynamic performance as well as the influence of stator blade geometry on cavitation. A steady-state homogeneous computational fluid dynamics (CFD) model was developed and validated against test data. It was found that cavitation brought severe capacity constant degradation under low-speed ratio (SR) operating conditions and vanished in high-speed ratio operating conditions. A design of experiments (DOE) study was performed to investigate the influence of stator design variables on cavitation over various operating conditions, and it was found that stator blade geometry had a significant effect on cavitation behavior. The results show that stator blade count and leaning angle are important variables in terms of capacity constant loss, torque ratio (TR) variance, and duration of cavitation. Large leaning angles are recommended due to their ability to increase the cavitation number in torque converters over a wide range of SRs, leading to less stall capacity loss as well as a shorter duration of cavitation. A reduced stator blade count is also suggested due to a reduced TR loss and capacity loss at stall.

Measurement and Analysis of Static Pressure Field in a Torque Converter Pump

1995 ◽  
Vol 117 (1) ◽  
pp. 109-115 ◽  
Author(s):  
R. R. By ◽  
B. Lakshminarayana
Keyword(s):  
Pressure Distribution ◽  
Potential Flow ◽  
Static Pressure ◽  
Pressure Field ◽  
Pressure Rise ◽  
Torque Converter ◽  
Speed Ratio ◽  
Pump Speed ◽  
The Core ◽  
Static Pressure Distribution

In this paper, the static pressure field and performance parameters of a torque converter pump are measured, analyzed, and interpreted under three turbine/pump speed ratio conditions (0, 0.6, and 0.8). A potential flow code is used to predict the static pressure distribution. Results show that: 1) centrifugal force has a dominant effect on the static pressure rise in the pump; 2) the static pressure field is generally poor at the core section; and 3) the potential flow code can fairly well predict the static pressure distribution at the blade mid-span, but not at the core and shell sections.

Sign in / Sign up

Export Citation Format

Share Document