scholarly journals Navier–Stokes and Potential Calculations of Axial Spacing Effect on Vortical and Potential Disturbances and Gust Response in an Axial Compressor

1997 ◽  
Vol 119 (3) ◽  
pp. 472-481 ◽  
Author(s):  
M.-H. Chung ◽  
A. M. Wo
Keyword(s):  
Spacing Effect ◽  
Axial Compressor ◽  
Leading Edge ◽  
Moving Frame ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Blade Row ◽  
Vortical Disturbance ◽  
Blade Row Interaction ◽  
Gust Response

The effect of blade row axial spacing on vortical and potential disturbances and gust response is studied for a compressor stator/rotor configuration near design and at high loadings using two-dimensional incompressible Navier–Stokes and potential codes, both written for multistage calculations. First, vortical and potential disturbances downstream of the isolated stator in the moving frame are defined; these disturbances exclude blade row interaction effects. Then, vortical and potential disturbances for the stator/rotor configuration are calculated for axial gaps of 10, 20, and 30 percent chord. Results show that the potential disturbance is uncoupled locally; the potential disturbance calculated from the isolated stator configuration is a good approximation for that from the stator/rotor configuration upstream of the rotor leading edge at the locations studied. The vortical disturbance depends strongly on blade row interactions. Low-order modes of vortical disturbance are of substantial magnitude and decay much more slowly downstream than do those of potential disturbance. Vortical disturbance decays linearly with increasing mode except very close to the stator trailing edge. For a small axial gap, e.g., 10 percent chord, both vortical and potential disturbances must be included to determine the rotor gust response.

scholarly journals Navier-Stokes and Potential Calculations of Axial Spacing Effect on Vortical and Potential Disturbances and Gust Response in an Axial Compressor

1995 ◽  
Author(s):  
Meng-Hsuan Chung ◽  
Andrew M. Wo
Keyword(s):  
Lower Order ◽  
Spacing Effect ◽  
Axial Compressor ◽  
Interaction Effects ◽  
Moving Frame ◽  
Navier Stokes ◽  
Blade Row ◽  
Vortical Disturbance ◽  
Blade Row Interaction ◽  
Gust Response

The effect of blade row axial spacing on vortical and potential disturbances and gust response is studied for a compressor stator/rotor configuration near design and at high loadings using 2D incompressible Navier-Stokes and potential codes, both written for multistage calculations. First, vortical and potential disturbances downstream of the isolated stator in the moving frame are defined; these disturbances exclude blade row interaction effects. Then, vortical and potential disturbances for the stator/rotor configuration are calculated for axial gaps of 10%, 20%, and 30% chord. Results show that the potential disturbance is uncoupled; the potential disturbance calculated from the isolated stator configuration is a good approximation for that from the stator/rotor configuration for all three axial gaps. The vortical disturbance depends strongly on blade row interactions. Low order modes of vortical disturbance are of substantial magnitude and decay much more slowly downstream than do those of potential disturbance. Vortical disturbance decays linearly with increasing mode except very close to the stator trailing edge. For a small axial gap, lower order modes of both vortical and potential disturbances must be included to determine the rotor gust response.

A Numerical Investigation of the Interaction Between Rotor Bow Waves and Upstream Wake Generators in a Transonic Compressor Stage

2003 ◽  
Author(s):  
Gregory Bloch ◽  
James Loellbach ◽  
Chunill Hah
Keyword(s):  
Numerical Investigation ◽  
Rotor Blade ◽  
Similar Case ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Transonic Compressor ◽  
Blade Row ◽  
Transonic Axial Compressor ◽  
Main Effects ◽  
Blade Row Interaction

A numerical investigation of unsteady blade row interaction in a transonic axial compressor was performed. The compressor consists of an upstream wake generator (WG) blade row followed by a rotor blade row. Blade row interaction consists of two main effects: the downstream influence on the rotor flowfield of wakes and unsteady vortices shed from the wake generator, and the upstream influence on the wake generator of the rotor bow shock waves. An unsteady, two-dimensional, Navier-Stokes simulation was performed at the 75% span location of the compressor. Results from the numerical simulation are compared to previously reported numerical results and to experimental measurements from a similar case.

scholarly journals Wake Vorticity Decay and Blade Response in an Axial Compressor With Varying Axial Gap

1999 ◽  
Author(s):  
A. M. Wo ◽  
M. H. Chung ◽  
S. J. Chang ◽  
S. F. Lee
Keyword(s):  
Large Scale ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Rotor Wake ◽  
Blade Loading ◽  
Wake Interaction ◽  
Blade Row ◽  
Unsteady Force ◽  
Gap Spacing ◽  
Blade Row Interaction

This paper addresses the decay of rotor wake vorticity for a rotor/stator axial compressor, with the axial gap between blade rows being 10, 20 and 30 percent chord, and at both design and high loading levels. Experiments were conducted in a large-scale, low-speed axial compressor. Navier-Stokes calculations were also executed. Both data and Navier-Stokes results reveal that the decay of rotor wake vorticity increases substantially as the axial gap decreases; the decay for 10 percent gap is about twice that of 30 percent. Increased time-mean blade loading causes the vorticity decay to also increase, with this effect more pronounced for large axial gap than small. At the stator inlet mid-pitch location, the wake maximum vorticity for 10 and 30 percent chord gap cases being nearly the same (differ by 3.8%) at design loading. The corresponding stator unsteady force agrees within 5.2%. Variation of vorticity decay with axial gap is directly linked to the change in potential disturbance by the downstream stator on the rotor wake due to the change in gap spacing. This suggests that the stator potential disturbance causes the upstream rotor wake to decay at an increased rate which, in turns, results in a lowered level of stator response compared to that without this stator/wake interaction effect. Thus, in this context, blade row interaction is considered beneficial.

scholarly journals Experimental and Numerical Study of Gust and Gust Response in a Rotor/Stator Axial Compressor

1996 ◽  
Author(s):  
Shu-Tzung Hsu ◽  
Andrew M. Wo ◽  
Chun-Kai Wu
Keyword(s):  
Large Scale ◽  
Numerical Study ◽  
Axial Compressor ◽  
Leading Edge ◽  
Navier Stokes ◽  
Potential Contribution ◽  
Rotor Wake ◽  
Low Speed ◽  
Measured Response ◽  
Gust Response

This paper addresses the gust response on the stator of a rotor/stator axial compressor, by decomposing the response into vortical and potential contributions. Experiments were conducted in a large-scale, low-speed compressor rig, with two axial gap cases — 10% and 30% chord — and at two time-mean loadings. To determine the gust response due to potential contribution, a two-step approach was taken. First, a panel code was used to determine the gust in the mid-gap plane for the rotor/stator configuration. Then, this calculated gust served as an inlet boundary of a Reynolds-averaged Navier-Stokes code for the stator cascade configuration. The vortical contributed gust response was found by subtracting the potential contributed response from the measured response. Results show that the vortical contributed response is largest near the instant when the rotor wake impinges at the stator leading edge. The potential contributed response reaches a maximum when the rotor trailing edge is axially upstream of the stator leading edge. The vortical contributed response dominates for all cases studied.

scholarly journals Reduction of Unsteady Blade Loading by Beneficial Use of Vortical and Potential Disturbances in an Axial Compressor With Rotor Clocking

1998 ◽  
Vol 120 (4) ◽  
pp. 705-713 ◽  
Author(s):  
S. T. Hsu ◽  
A. M. Wo
Keyword(s):  
Large Scale ◽  
Axial Compressor ◽  
Leading Edge ◽  
Forced Response ◽  
Suction Surface ◽  
Blade Loading ◽  
Beneficial Use ◽  
Unsteady Loading ◽  
Vortical Disturbance ◽  
First Time

This paper demonstrates reduction of stator unsteady loading due to forced response in a large-scale, low-speed, rotor/stator/rotor axial compressor rig by clocking the downstream rotor. Data from the rotor/stator configuration showed that the stator response due to the upstream vortical disturbance reaches a maximum when the wake impinges against the suction surface immediately downstream of the leading edge. Results from the stator/rotor configuration revealed that the stator response due to the downstream potential disturbance reaches a minimum with a slight time delay after the rotor sweeps pass the stator trailing edge. For the rotor/stator/rotor configuration, with Gap1 = 10 percent chord and Gap2 = 30 percent chord, results showed a 60 percent reduction in the stator force amplitude by clocking the downstream rotor so that the time occurrence of the maximum force due to the upstream vortical disturbance coincides with that of the minimum force due to the downstream potential disturbance. This is the first time, the authors believe, that beneficial use of flow unsteadiness is definitively demonstrated to reduce the blade unsteady loading.

scholarly journals Numerical Optimization of a Stall Margin Enhancing Recirculation Channel for an Axial Compressor

Fluids ◽  
2019 ◽  
Vol 4 (2) ◽  
pp. 88
Author(s):  
Motoyuki Kawase ◽  
Aldo Rona
Keyword(s):  
High Speed ◽  
High Performance ◽  
Fluid Dynamic ◽  
Axial Compressor ◽  
Leading Edge ◽  
Navier Stokes ◽  
Test Case ◽  
Dynamic Simulations ◽  
Stall Margin ◽  
Casing Treatment

A proof of concept is provided by computational fluid dynamic simulations of a new recirculating type casing treatment. This treatment aims at extending the stable operating range of highly loaded axial compressors, so to improve the safety of sorties of high-speed, high-performance aircraft powered by high specific thrust engines. This casing treatment, featuring an axisymmetric recirculation channel, is evaluated on the NASA rotor 37 test case by steady and unsteady Reynolds Averaged Navier Stokes (RANS) simulations, using the realizable k-ε model. Flow blockage at the recirculation channel outlet was mitigated by chamfering the exit of the recirculation channel inner wall. The channel axial location from the rotor blade tip leading edge was optimized parametrically over the range −4.6% to 47.6% of the rotor tip axial chord c z . Locating the channel at 18.2% c z provided the best stall margin gain of approximately 5.5% compared to the untreated rotor. No rotor adiabatic efficiency was lost by the application of this casing treatment. The investigation into the flow structure with the recirculating channel gave a good insight into how the new casing treatment generates this benefit. The combination of stall margin gain at no rotor adiabatic efficiency loss makes this design attractive for applications to high-speed gas turbine engines.

Evaluation of Unsteady CFD Methods by Their Application to a Transonic Propfan Stage

2001 ◽  
Author(s):  
S. Schmitt ◽  
F. Eulitz ◽  
L. Wallscheid ◽  
A. Arnone ◽  
M. Marconcini
Keyword(s):  
Numerical Methods ◽  
Navier Stokes ◽  
Test Case ◽  
Flow Angle ◽  
Laser Measurements ◽  
General Flow ◽  
Blade Row ◽  
Flow Features ◽  
Blade Row Interaction ◽  
Good Agreement

The accuracy in predicting the unsteady aerodynamic blade-row-interaction of two state-of-the-art Navier-Stokes codes is evaluated within the current paper. The general flow features of the test case — a transonic research propfan stage — are described in brief as far as necessary to understand the detailed comparisons. The calculated unsteady velocity and flow angle distributions at various axial planes of the stage are compared to data from unsteady laser measurements. The general flow features of the propfan are very well reproduced by the numerical methods and a good agreement is also obtained in comparison to the measured data. One important outcome of the comparison is the good agreement of both numerical methods with the unsteady fluctuations measured in the experiment.

Numerical Flow Analysis in a Subsonic Vaned Radial Diffuser With Leading Edge Redesign

1999 ◽  
Vol 121 (1) ◽  
pp. 119-126 ◽  
Author(s):  
E. Casartelli ◽  
A. P. Saxer ◽  
G. Gyarmathy
Keyword(s):  
Static Pressure ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Leading Edge ◽  
Inverse Design ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Characteristic Lines ◽  
Design Software

The flow field in a subsonic vaned radial diffuser of a single-stage centrifugal compressor is numerically investigated using a three-dimensional Navier–Stokes solver (TASCflow) and a two-dimensional analysis and inverse-design software package (MISES). The vane geometry is modified in the leading edge area (two-dimensional blade shaping) using MISES, without changing the diffuser throughflow characteristics. An analysis of the two-dimensional and three-dimensional effects of two redesigns on the flow in each of the diffuser subcomponents is performed in terms of static pressure recovery, total pressure loss production, and secondary flow reduction. The computed characteristic lines are compared with measurements, which confirm the improvement obtained by the leading edge redesign in terms of increased pressure rise and operating range.

Aerodynamic Origin of Rotor-Rotor Interaction Noise From Unducted Propulsors

2013 ◽  
Author(s):  
Florian Danner ◽  
Christofer Kendall-Torry ◽  
Hans-Peter Kau
Keyword(s):  
Stokes Equations ◽  
Navier Stokes ◽  
Propagation Characteristics ◽  
Propulsion Systems ◽  
Navier Stokes Equations ◽  
Pressure Distributions ◽  
Blade Row ◽  
Open Rotor ◽  
Blade Row Interaction ◽  
Insight Into

The sound arising from blade row interaction in open rotor propulsion systems is known to significantly contribute to overall noise emissions. The present paper therefore addresses the origination of rotor-rotor interaction noise from a pair of unducted counter-rotating fans. The focus is on the aerodynamic mechanisms that involve sound generation, in order to provide the physical understanding required to find noise-reducing means. Detailed insight into the underlying phenomena is provided on the basis of numerical simulations applying the unsteady Reynolds-averaged Navier-Stokes equations. The interaction mechanisms are identified by extracting the time-dependent disturbances of the flow field in the respective rotor relative frame of reference. Conclusions on the sources of interaction noise and potential noise-reducing means are drawn by evaluating polar directivities, blade surface pressure distributions and propagation characteristics.

Experimental and Numerical Verification of the Core-Flow in a New Low-Pressure Turbine

2016 ◽  
Author(s):  
Michael Henke ◽  
Lars Wein ◽  
Tim Kluge ◽  
Yavuz Guendogdu ◽  
Marc Heinz-Otto Biester ◽  
...  
Keyword(s):  
Flow Field ◽  
Low Pressure ◽  
Numerical Verification ◽  
Two Dimensional ◽  
Core Flow ◽  
Low Pressure Turbine ◽  
The Core ◽  
Blade Row ◽  
Unsteady Effects ◽  
Blade Row Interaction

The flow field in modern axial turbines is non-trivial and highly unsteady due to secondary flow and blade row interaction. In recent years, existing design-tools like two-dimensional flow solvers as well as fully three-dimensional CFD methods have been validated for the assumption of a quasi-steady flow field. Since the inevitable unsteadiness of the flow field has a direct impact on unsteady loss generation and work transfer, existing design methods stand in need of validation for local unsteady effects within the flow field. In order to clearly separate end-wall losses from those generated by blade row interaction within the blade passage, a two-dimensional core-flow is essential for the investigation. Hence, a new 1.5-stage high aspect ratio low pressure turbine has been designed to determine the intensity of core-flow blade row interaction for different axial gaps. First, inlet and outlet conditions of the test rig are evaluated with regard to homogeneity of the flow parameters in their radial and circumferential distributions. Secondly, the measurement data gained from rig tests have been applied as boundary conditions to time-averaged numerical computations. The flow field analysis for two different axial gaps focuses on the verification of the core flow. The authors show that the new turbine has been successfully verified using both test data and the numerical predictions, serving as a precondition for the validation of the numerical model for unsteady effects within the core-flow.

Sign in / Sign up

Export Citation Format

Share Document