Passive, Adaptive and Active Tuned Vibration Absorbers—A Survey

1995 ◽  
Vol 117 (B) ◽  
pp. 234-242 ◽  
Author(s):  
J. Q. Sun ◽  
M. R. Jolly ◽  
M. A. Norris
Keyword(s):  
Recent Progress ◽  
Noise Suppression ◽  
Vibration Absorbers ◽  
Optimal Tuning ◽  
Tuned Vibration Absorbers ◽  
On Line ◽  
Fail Safe

An overview of the recent development of tuned vibration absorbers (TVAs) for vibration and noise suppression is presented. The paper summarizes some popular theory for analysis and optimal tuning of these devices, discusses various design configurations, and presents some contemporary applications of passive TVAs. Furthermore, the paper also presents a brief discussion on the recent progress of adaptive and semi-active TVAs along with their on-line tuning strategies, and active and hybrid fail-safe TVAs.

Passive, Adaptive and Active Tuned Vibration Absorbers—A Survey

1995 ◽  
Vol 117 (B) ◽  
pp. 234-242 ◽  
Author(s):  
J. Q. Sun ◽  
M. R. Jolly ◽  
M. A. Norris
Keyword(s):  
Recent Progress ◽  
Noise Suppression ◽  
Vibration Absorbers ◽  
Optimal Tuning ◽  
Tuned Vibration Absorbers ◽  
On Line ◽  
Fail Safe

An overview of the recent development of tuned vibration absorbers (TVAs) for vibration and noise suppression is presented. The paper summarizes some popular theory for analysis and optimal tuning of these devices, discusses various design configurations, and presents some contemporary applications of passive TVAs. Furthermore, the paper also presents a brief discussion on the recent progress of adaptive and semi-active TVAs along with their on-line tuning strategies, and active and hybrid fail-safe TVAs.

Implementation of Tuned Vibration Absorbers for Above Ground Pipeline Vibration Control

2000 ◽  
Author(s):  
Mark A. Norris ◽  
Keith R. Ptak ◽  
Ben A. Zamora ◽  
James D. Hart
Keyword(s):  
Vibration Control ◽  
Vibration Suppression ◽  
The Arctic ◽  
Vibration Absorbers ◽  
Recent Application ◽  
Optimal Tuning ◽  
Tuned Vibration Absorbers ◽  
Recent Developments ◽  
Environmental Considerations ◽  
Pipeline Vibration

An overview of recent developments of tuned vibration absorbers (TVAs) for vibration suppression is presented. The paper summarizes some popular theory for analysis and optimal tuning of these devices, discusses various design configurations, and reviews the recent application of TVAs to control wind-induced oscillations of pipelines above the Arctic Circle. Although the wind-induced pipeline vibrations are relatively small, the accumulation of vibration cycles can cause fatigue at pipeline joints. The TVAs used in this application have reduced the RMS displacements of the pipeline by as much as a factor of seven. Additionally, the paper introduces a new overhead TVA installation on the pipeline for accommodating environmental considerations.

VIBRATIONAL ENERGIES OF MEMBERS IN STRUCTURAL NETWORKS FITTED WITH TUNED VIBRATION ABSORBERS

2006 ◽  
Vol 06 (02) ◽  
pp. 269-284 ◽  
Author(s):  
SUNNY K. GEORGE ◽  
K. SHANKAR
Keyword(s):  
Energy Level ◽  
Vibrational Energy ◽  
General Structure ◽  
Energy Levels ◽  
Complex Structure ◽  
Input Power ◽  
Vibration Absorbers ◽  
Tuned Vibration Absorbers ◽  
Vibrational Energies ◽  
Structural Networks

The distribution of vibrational energy in members of a complex structure with tuned absorbers attached at the joints and subjected to dynamic loading is studied. The concept of power flows through the structure is used to determine the time-averaged energy levels of each member in the structure. The power flows are calculated using the time-averaged product of force and velocity at the input and coupling points (joints) of a general structure made of axially vibrating rods. The receptance approach is used to calculate the coupling forces and velocities in the structure. By balancing the input power against the dissipated powers, the time-averaged energy levels in members are determined. The main criteria studied here is the reduction in the frequency-averaged vibrational energy level of a member when an absorber is attached, expressed as a percentage compared to the case where there are no absorbers. The concept is first illustrated with a simple model of 2 axially vibrating rods with an absorber attached to the joint. Next, a more complex structure comprising 8 rods with arbitrary orientations and several absorbers attached to junctions is studied. The effect of activating absorbers at various locations on reducing the energy levels of certain members is examined. It is possible to estimate the usefulness of the absorber with respect to any member by determining the percentage reduction of energy level for that member.

Payload noise suppression using distributed active vibration absorbers

2002 ◽  
Author(s):  
Stephen D. O'Regan ◽  
Bart Burkewitz ◽  
Christopher Fuller ◽  
Steven A. Lane ◽  
Marty Johnson
Keyword(s):  
Noise Suppression ◽  
Vibration Absorbers ◽  
Active Vibration

Particle Dampers for Workpiece Chatter Mitigation

2005 ◽  
Author(s):  
Neil D. Sims ◽  
Ashan Amarasinghe ◽  
Keith Ridgway
Keyword(s):  
Wide Frequency Range ◽  
Machining Process ◽  
Design Parameters ◽  
Depth Of Cut ◽  
Vibration Absorbers ◽  
Tuned Vibration Absorbers ◽  
Highly Nonlinear ◽  
Machining System ◽  
Order Of Magnitude ◽  
Particle Dampers

It is well known that the chatter stability of a machining process can be improved by increasing the structural damping of the system. To date this approach has been effectively used on various components of the machining system, for example boring bars, milling tools, and the machine structure itself. Various damping treatments have been proposed, including tuned vibration absorbers, active methods, and impact dampers. However, to date there has been little or no work to investigate the issue of particle dampers for this application. This special class of damper comprises a container of thousands of small granular particles which dissipate energy by friction and impact when the container vibrates. The resulting behaviour is highly nonlinear but can provide very high levels of damping across a wide frequency range. In the present study, particle dampers were applied to a workpiece to mitigate chatter during milling, and the limiting critical depth of cut was increased by an order of magnitude. This article gives an overview of the particle damper’s behaviour and key design parameters. Cutting trials employing the device are then described.

Order-Tuned Vibration Absorbers for Cyclic Rotating Flexible Structures

2005 ◽  
Author(s):  
Brian J. Olson ◽  
Steve W. Shaw ◽  
Christophe Pierre
Keyword(s):  
Equations Of Motion ◽  
Flexible Structures ◽  
Closed Form Solution ◽  
Nonlinear Effects ◽  
Form Solution ◽  
Vibration Absorbers ◽  
Bladed Disk ◽  
Tuned Vibration Absorbers ◽  
Engine Order ◽  
Bladed Disk Assembly

This paper investigates the use of order-tuned absorbers to attenuate vibrations of flexible blades in a bladed disk assembly subjected to engine order excitation. The blades are modeled by a cyclic chain of N oscillators, and a single vibration absorber is fitted to each blade. These absorbers exploit the centrifugal field arising from rotation so that they are tuned to a given order of rotation, rather than to a fixed frequency. A standard change of coordinates based on the cyclic symmetry of the system essentially decouples the governing equations of motion, yielding a closed form solution for the steady-state response of the overall system. These results show that optimal reduction of blade vibrations is achieved by tuning the absorbers to the excitation order n, but that the resulting system is highly sensitive to small perturbations. Intentional detuning (meaning that the absorbers are slightly over- or under-tuned relative to n) can be implemented to improve the robustness of the design. It is shown that by slightly undertuning the absorbers there are no system resonances near the excitation order of interest and that the resulting system is robust to mistuning (i.e., small random uncertainties in the system parameters) of the absorbers and/or blades. These results offer a basic understanding of the dynamics of a bladed disk assembly fitted with order-tuned vibration absorbers, and serve as a first step to the investigation of more realistic models, where, for example, imperfections and nonlinear effects are considered, and multi-DOF and general-path absorbers are employed.

scholarly journals Hybrid Secondary Suspension Systems

2009 ◽  
Vol 16 (5) ◽  
pp. 467-480 ◽  
Author(s):  
Nader Vahdati ◽  
Mehdi Ahmadian
Keyword(s):  
Mathematical Model ◽  
Vibration Absorbers ◽  
Simple Mathematical Model ◽  
System Behavior ◽  
Engine Mounts ◽  
Suspension Systems ◽  
Tuned Vibration Absorbers ◽  
Simulation Results ◽  
Secondary Suspension ◽  
The Mathematical Model

Passive fluid mounts are used in the fixed wing applications as engine mounts. The passive fluid mount is placed in between the engine and the fuselage to reduce the cabin's structure- borne noise and vibration generated by the engine.To investigate the benefits of passive fluid mounts used in conjunction with tuned vibration absorbers (TVA), a simple mathematical model is developed. This mathematical model includes the mathematical model of a passive fluid mount, a TVA, and a spring representing the fuselage structure. The simulation results indicate that when passive fluid mounts are used in conjunction with TVAs, an active suspension system behavior is nearly created.

Experimental Validation of a State-Switched Absorber Used to Control Vibrating Continuous Systems

2005 ◽  
Author(s):  
Mark Holdhusen ◽  
Kenneth A. Cunefare
Keyword(s):  
Experimental Validation ◽  
Frequency Component ◽  
Effective Bandwidth ◽  
Continuous Systems ◽  
Vibration Absorbers ◽  
Numerical Work ◽  
Tuned Vibration Absorbers ◽  
Resonance Frequencies ◽  
Magneto Rheological ◽  
The Magnetic Field

A state-switched absorber (SSA) is a device capable of instantaneously changing its stiffness, thus it can switch between resonance frequencies, increasing its effective bandwidth as compared to classical tuned vibration absorbers for vibration control. Previous numerical work has shown that an optimized SSA outperforms an optimized TVA at controlling vibrations of both a beam and a plate. This paper details the experimental validation of these simulation results. An SSA was realized by employing magneto-rheological elastomers to achieve a stiffness change. The stiffness of these elastomers is a function of the magnetic field put across them. Experiments were conducted on both a cantilever beam and a square plate clamped on all sides. Each system was excited by several two-frequency component excitations. For each forcing combination, several tuning configurations of the SSA were applied and the kinetic energy of the system was found. This observed performance was compared to the performance found through numerical simulations of a system with a similar tuning and excitation configuration. It was found that the observed performance follows closely with results found through numerical simulation.

Sign in / Sign up

Export Citation Format

Share Document