Flow Resistance Correlation of Wire Nets in a Wide Range of Reynolds Numbers for Thermal Design of Electronic Equipment

1996 ◽  
Vol 118 (3) ◽  
pp. 611-612 ◽  
Author(s):  
Masaru Ishizuka
Keyword(s):  
Flow Resistance ◽  
Reynolds Numbers ◽  
Thermal Design ◽  
Electronic Equipment ◽  
Wide Range

The effects of the outlet area and the location of the main power supply unit on the cooling capability through naturally air-cooled electronic equipment casings

1998 ◽  
Vol 212 (5) ◽  
pp. 381-383 ◽  
Author(s):  
M Ishizuka
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Power Supply ◽  
Flow Resistance ◽  
Thermal Design ◽  
Electronic Equipment ◽  
Power Supply Unit ◽  
Air Cooling ◽  
Uniform Temperature ◽  
Cooling Systems

This paper describes a practical thermal design approach to natural air-cooled electronic equipment casings. A set of simplified equations for the thermal design of natural air-cooled electronic equipment casings has been proposed. The proposed set of equations satisfied the demand of practical air-cooling systems, since it takes account of factors such as the stack effect, the air flow resistance and the heat transfer due to natural convection. The effects of the outlet area and the location of the main power supply unit on the natural cooling capability of electronic equipment casings were studied using a set of equations. The results have shown that a uniform temperature distribution could be achieved when the main power supply unit was placed at the bottom of the casing. It has also been suggested that the value of the heat removed from the casing surface could be more significant than that from the outlet vent in the thermal design of natural air-cooled electronic equipment casings.

Flow Resistance Network Analysis in Fan-Cooled High-Density Packaging Electronic Equipment

2015 ◽  
Author(s):  
Takashi Fukue ◽  
Tomoyuki Hatakeyama ◽  
Masaru Ishizuka ◽  
Koichi Hirose ◽  
Kazuma Obata ◽  
...  
Keyword(s):  
Network Analysis ◽  
Flow Resistance ◽  
High Density ◽  
Thermal Design ◽  
Electronic Equipment ◽  
Test Model ◽  
Resistance Network ◽  
Electrical Components ◽  
Cooling Air ◽  
High Density Packaging

This study describes an application of the flow resistance network analysis to thermal design of fan-cooled electronic equipment. Especially, a modeling method of the flow resistance network was investigated. Current electronic equipment becomes smaller and thinner while their functions become more complex. As a result, flow passages for cooling air become complex. In order to simulate the complex airflow in high-density packaging electronic equipment by using the flow resistance network, we tried to develop the flow resistance network by support of the 3D-CFD analysis. A test model which simulates high-density packaging electronic equipment is prepared and the flow resistance network analysis is applied to the prediction of flow rate distribution in the model. Through the investigation, we obtained information and future problems about the development of the flow resistance network in electronic equipment with lots of electrical components.

Turbulent three-dimensional dielectric electrohydrodynamic convection between two plates

2012 ◽  
Vol 696 ◽  
pp. 228-262 ◽  
Author(s):  
A. Kourmatzis ◽  
J. S. Shrimpton
Keyword(s):  
Spatial Data ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Two Dimensions ◽  
Three Dimensions ◽  
Energy Budgets ◽  
Turbulent Regime ◽  
Scalar Flux ◽  
Wide Range ◽  
Scalar Variance

AbstractThe fundamental mechanisms responsible for the creation of electrohydrodynamically driven roll structures in free electroconvection between two plates are analysed with reference to traditional Rayleigh–Bénard convection (RBC). Previously available knowledge limited to two dimensions is extended to three-dimensions, and a wide range of electric Reynolds numbers is analysed, extending into a fully inherently three-dimensional turbulent regime. Results reveal that structures appearing in three-dimensional electrohydrodynamics (EHD) are similar to those observed for RBC, and while two-dimensional EHD results bear some similarities with the three-dimensional results there are distinct differences. Analysis of two-point correlations and integral length scales show that full three-dimensional electroconvection is more chaotic than in two dimensions and this is also noted by qualitatively observing the roll structures that arise for both low (${\mathit{Re}}_{E} = 1$) and high electric Reynolds numbers (up to ${\mathit{Re}}_{E} = 120$). Furthermore, calculations of mean profiles and second-order moments along with energy budgets and spectra have examined the validity of neglecting the fluctuating electric field ${ E}_{i}^{\ensuremath{\prime} } $ in the Reynolds-averaged EHD equations and provide insight into the generation and transport mechanisms of turbulent EHD. Spectral and spatial data clearly indicate how fluctuating energy is transferred from electrical to hydrodynamic forms, on moving through the domain away from the charging electrode. It is shown that ${ E}_{i}^{\ensuremath{\prime} } $ is not negligible close to the walls and terms acting as sources and sinks in the turbulent kinetic energy, turbulent scalar flux and turbulent scalar variance equations are examined. Profiles of hydrodynamic terms in the budgets resemble those in the literature for RBC; however there are terms specific to EHD that are significant, indicating that the transfer of energy in EHD is also attributed to further electrodynamic terms and a strong coupling exists between the charge flux and variance, due to the ionic drift term.

scholarly journals Focusing of Particles in a Microchannel with Laser Engraved Groove Arrays

Biosensors ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 263
Author(s):  
Tianlong Zhang ◽  
Yigang Shen ◽  
Ryota Kiya ◽  
Dian Anggraini ◽  
Tao Tang ◽  
...  
Keyword(s):  
Open Space ◽  
Lateral Displacement ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Particle Sedimentation ◽  
Nanoparticle Separation ◽  
Wide Range ◽  
Fs Laser ◽  
Channel Bottom ◽  
Myoblast Cells

Continuous microfluidic focusing of particles, both synthetic and biological, is significant for a wide range of applications in industry, biology and biomedicine. In this study, we demonstrate the focusing of particles in a microchannel embedded with glass grooves engraved by femtosecond pulse (fs) laser. Results showed that the laser-engraved microstructures were capable of directing polystyrene particles and mouse myoblast cells (C2C12) towards the center of the microchannel at low Reynolds numbers (Re < 1). Numerical simulation revealed that localized side-to-center secondary flows induced by grooves at the channel bottom play an essential role in particle lateral displacement. Additionally, the focusing performance proved to be dependent on the angle of grooves and the middle open space between the grooves based on both experiments and simulation. Particle sedimentation rate was found to critically influence the focusing of particles of different sizes. Taking advantage of the size-dependent particle lateral displacement, selective focusing of micrometer particles was demonstrated. This study systematically investigated continuous particle focusing in a groove-embedded microchannel. We expect that this device will be used for further applications, such as cell sensing and nanoparticle separation in biological and biomedical areas.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

Predictions of the Effect of Roughness on Heat Transfer From Turbine Airfoils

1998 ◽  
Author(s):  
Anil K. Tolpadi ◽  
Michael E. Crawford
Keyword(s):  
Heat Transfer ◽  
Side Surface ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Surface Finishing ◽  
Transfer Coefficients ◽  
Average Roughness ◽  
Wide Range ◽  
Turbine Airfoils ◽  
Good Agreement

The heat transfer and aerodynamic performance of turbine airfoils are greatly influenced by the gas side surface finish. In order to operate at higher efficiencies and to have reduced cooling requirements, airfoil designs require better surface finishing processes to create smoother surfaces. In this paper, three different cast airfoils were analyzed: the first airfoil was grit blasted and codep coated, the second airfoil was tumbled and aluminide coated, and the third airfoil was polished further. Each of these airfoils had different levels of roughness. The TEXSTAN boundary layer code was used to make predictions of the heat transfer along both the pressure and suction sides of all three airfoils. These predictions have been compared to corresponding heat transfer data reported earlier by Abuaf et al. (1997). The data were obtained over a wide range of Reynolds numbers simulating typical aircraft engine conditions. A three-parameter full-cone based roughness model was implemented in TEXSTAN and used for the predictions. The three parameters were the centerline average roughness, the cone height and the cone-to-cone pitch. The heat transfer coefficient predictions indicated good agreement with the data over most Reynolds numbers and for all airfoils-both pressure and suction sides. The transition location on the pressure side was well predicted for all airfoils; on the suction side, transition was well predicted at the higher Reynolds numbers but was computed to be somewhat early at the lower Reynolds numbers. Also, at lower Reynolds numbers, the heat transfer coefficients were not in very good agreement with the data on the suction side.

CFD Simulation of Fluid Flow Through Porous Media: Application to Decomposed Gases Flow Through Foam Pattern in Lost Foam Casting

Materials ◽  
2003 ◽  
Author(s):  
Sayavur I. Bakhtiyarov ◽  
Ruel A. Overfelt
Keyword(s):  
Cfd Simulation ◽  
Reynolds Numbers ◽  
Phase Flow ◽  
Flow Through Porous Media ◽  
Foam Material ◽  
Element Analysis ◽  
Wide Range ◽  
Flow Through ◽  
Foam Pattern ◽  
Lost Foam

Numerical simulation of decomposed gases through foam pattern was conducted using finite element analysis. A new kinetic model is proposed for gaseos phase flow between molten metal and foam material. The computations were performed for a wide range of Reynolds numbers. The results of the simulations are compared with the experiemental data obtained in this study.

Calculation of the primary trajectories of seeds and other particles in strong winds

1983 ◽  
Vol 219 (1215) ◽  
pp. 217-217
Keyword(s):  
Equations Of Motion ◽  
Aerodynamic Resistance ◽  
Reynolds Numbers ◽  
Spherical Particles ◽  
Spores And Pollen ◽  
General Terms ◽  
Wide Range ◽  
Strong Winds ◽  
Dispersal Distances ◽  
Enormous Number

The movement of variously dense spherical particles representing a variety of seeds, fruits, spores and pollen, and released from rest into arbitrary winds and a gravitational field is discussed in general terms that account in detail for changes in the quasi-static aerodynamic resistance to motion experienced by such particles during aerial flight. A hybrid analytical-empirical law is established which describes this resistance fairly accurately for particle Reynolds numbers in the range 0—60 000 and that allows for the numerical integration of the equations of motion so as to cover a very wide range of flight conditions. This makes possible the provision of a set of four-parameter universal range tables from which the dispersal distances for an enormous number of practical cases may be estimated. One particular case of particle movement in a region of pseudo-thermal convection is also discussed and this shows how a marked degree of deposition concentration may be induced in some circumstances by such a flow. Botanists and ecologists concerned with seed and particle dispersal in the environment may find the universal range tables of particular interest and use. This is because the tables obviate the need for the integration of the equations of motion when dealing with individual cases and permit an estimation of range purely on the basis of the specified quantities of particle size, density and altitude of release, atmospheric wind speed, density and viscosity, and the acceleration due to gravity.

Sign in / Sign up

Export Citation Format

Share Document