Energy Approach to the Fatigue of 60/40 Solder: Part I—Influence of Temperature and Cycle Frequency

1995 ◽  
Vol 117 (2) ◽  
pp. 130-135 ◽  
Author(s):  
H. D. Solomon ◽  
E. D. Tolksdorf
Keyword(s):  
Fatigue Life ◽  
Flow Stress ◽  
Plastic Strain ◽  
Strain Rate ◽  
Hold Time ◽  
Rate Dependence ◽  
Cycle Frequency ◽  
Influence Of Temperature ◽  
Life Data ◽  
Governing Factor

This study correlates previously published fatigue life data with the hysteresis energy, and compares this to the previous correlation’s with the applied plastic strain. It was found that, while the hysteresis energy could be used to describe the fatigue life, corrections must be made to account for the temperature and strain rate dependence of the flow stress. Because of these factors, it is believed that the plastic strain, and not the hysteresis energy, is the true governing factor in determining the fatigue life. Part I (described here) covers only the influence of temperature and cycle frequency for symmetric cycling. Part II, to be published, will deal with hold time and asymmetric cycling.

The Influence of Temperature and Strain Rate on the Flow Stress of Magnesium Single Crystals

1960 ◽  
Vol 13 (2) ◽  
pp. 284 ◽  
Author(s):  
ZS Basinski
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Single Crystals ◽  
Rate Dependence ◽  
Close Similarity ◽  
Deformation Characteristics ◽  
Stress Strain ◽  
Influence Of Temperature ◽  
Cubic Metals ◽  
The Face

The temperature and strain rate-dependence of the flow stress of magnesium single crystals was measured in the temperature range 1� 45-248 oK. Some incidental observations were also made on the form of the stress-strain curves and the appearance of Blip lines. The deformation characteristics show close similarity with those of the face-centred cubic metals.

scholarly journals Characterization of Austenitic Stainless Steels with Regard to Environmentally Assisted Fatigue in Simulated Light Water Reactor Conditions

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 307
Author(s):  
Matthias Bruchhausen ◽  
Gintautas Dundulis ◽  
Alec McLennan ◽  
Sergio Arrieta ◽  
Tim Austin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Fatigue Life ◽  
Elevated Temperature ◽  
Strain Rate ◽  
Power Plants ◽  
Research Effort ◽  
Hold Time ◽  
Strain Range ◽  
Austenitic Steels ◽  
Mean Strain

A substantial amount of research effort has been applied to the field of environmentally assisted fatigue (EAF) due to the requirement to account for the EAF behaviour of metals for existing and new build nuclear power plants. We present the results of the European project INcreasing Safety in NPPs by Covering Gaps in Environmental Fatigue Assessment (INCEFA-PLUS), during which the sensitivities of strain range, environment, surface roughness, mean strain and hold times, as well as their interactions on the fatigue life of austenitic steels has been characterized. The project included a test campaign, during which more than 250 fatigue tests were performed. The tests did not reveal a significant effect of mean strain or hold time on fatigue life. An empirical model describing the fatigue life as a function of strain rate, environment and surface roughness is developed. There is evidence for statistically significant interaction effects between surface roughness and the environment, as well as between surface roughness and strain range. However, their impact on fatigue life is so small that they are not practically relevant and can in most cases be neglected. Reducing the environmental impact on fatigue life by modifying the temperature or strain rate leads to an increase of the fatigue life in agreement with predictions based on NUREG/CR-6909. A limited sub-programme on the sensitivity of hold times at elevated temperature at zero force conditions and at elevated temperature did not show the beneficial effect on fatigue life found in another study.

A Modified Peric Model for Al-Mg Alloy Sheet with Rate-Independent Initial Yield Stress at Warm Temperatures

2019 ◽  
Vol 287 ◽  
pp. 3-7
Author(s):  
Yong Zhang ◽  
Qing Zhang ◽  
Yuan Tao Sun ◽  
Xian Rong Qin
Keyword(s):  
Flow Stress ◽  
Plastic Strain ◽  
Strain Rate ◽  
Yield Stress ◽  
Constitutive Models ◽  
Mg Alloy ◽  
Initial Yield Stress ◽  
Initial Yield ◽  
Rate Dependent ◽  
Dependent Flow

The constitutive modeling of aluminum alloy under warm forming conditions generally considers the influence of temperature and strain rate. It has been shown by published flow stress curves of Al-Mg alloy that there is nearly no effect of strain rate on initial yield stress at various temperatures. However, most constitutive models ignored this phenomenon and may lead to inaccurate description. In order to capture the rate-independent initial yield stress, Peric model is modified via introducing plastic strain to multiply the strain rate, for eliminating the effect of strain rate when the plastic strain is zero. Other constitutive models including the Wagoner, modified Hockett–Sherby and Peric are also considered and compared. The results show that the modified Peric model could not only describe the temperature-and rate-dependent flow stress, but also capture the rate-independent initial yield stress, while the Wagoner, modified Hockett–Sherby and Peric model can only describe the temperature-and rate-dependent flow stress. Moreover, the modified Peric model could obtain proper static yield stress more naturally, and this property may have potential applications in rate-dependent simulations.

Strain-rate dependence of hardening and softening in compression of a bulk-metallic glass

2007 ◽  
Vol 22 (10) ◽  
pp. 2655-2658 ◽  
Author(s):  
W.H. Jiang ◽  
F.X. Liu ◽  
F. Jiang ◽  
K.Q. Qiu ◽  
H. Choo ◽  
...  
Keyword(s):  
Flow Stress ◽  
Metallic Glass ◽  
Strain Rate ◽  
Bulk Metallic Glass ◽  
Plastic Flow ◽  
Shear Banding ◽  
Constant Strain Rate ◽  
Rate Dependence ◽  
Strain Rate Dependence ◽  
Plastic Flow Stress

We investigated the effect of strain rate on the plastic-flow stress of a Zr-based bulk-metallic glass in quasistatic compression. The results indicate that the plastic-flow stress is dependent on the strain rate: an increase in the strain rate leads to a decrease in the plastic-flow stress, and vice versa. However, simply loading, unloading, and reloading at a constant strain rate do not change the plastic-flow stress. This strain-rate dependence of the plastic-flow stress may be related to shear-banding operations.

The Effect of Strain Rate on Low Cycle Fatigue Life with Hold Time for USC Candidate Rotor Material

2010 ◽  
pp. 217-229
Author(s):  
Kuk-cheol Kim ◽  
Byeong-ook Kong ◽  
Min-soo Kim ◽  
Sung-tae Kang
Keyword(s):  
Fatigue Life ◽  
Strain Rate ◽  
Low Cycle Fatigue ◽  
Hold Time ◽  
Cycle Fatigue

scholarly journals Strain Rate-Dependent Constitutive and Low Stress Triaxiality Fracture Behavior Investigation of 6005 Al Alloy

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Yong Peng ◽  
Xuanzhen Chen ◽  
Shan Peng ◽  
Chao Chen ◽  
Jiahao Li ◽  
...  
Keyword(s):  
Flow Stress ◽  
Plastic Strain ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Equivalent Plastic Strain ◽  
Stress Triaxiality ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Stress States

In order to study the dynamic and fracture behavior of 6005 aluminum alloy at different strain rates and stress states, various tests (tensile tests at different strain rates and tensile shearing tests at five stress states) are conducted by Mechanical Testing and Simulation (MTS) and split-Hopkinson tension bar (SHTB). Numerical simulations based on the finite element method (FEM) are performed with ABAQUS/Standard to obtain the actual stress triaxialities and equivalent plastic strain to fracture. The results of tensile tests for 6005 Al show obvious rate dependence on strain rates. The results obtained from simulations indicate the feature of nonmonotonicity between the strain to fracture and stress triaxiality. The equivalent plastic strain reduces to a minimum value and then increases in the stress triaxiality range from 0.04 to 0.30. A simplified Johnson-Cook (JC) constitutive model is proposed to depict the relationship between the flow stress and strain rate. What is more, the strain-rate factor is modified using a quadratic polynomial regression model, in which it is considered to vary with the strain and strain rates. A fracture criterion is also proposed in a low stress triaxiality range from 0.04 to 0.369. Error analysis for the modified JC model indicates that the model exhibits higher accuracy than the original one in predicting the flow stress at different strain rates. The fractography analysis indicates that the material has a typical ductile fracture mechanism including the shear fracture under pure shear and the dimple fracture under uniaxial tensile.

Sign in / Sign up

Export Citation Format

Share Document