Improving Film Cooling Performance Using Airfoil Contouring

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
Atul Kohli ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Suction Side ◽  
Design Tool ◽  
Optimization Process ◽  
Navier Stokes ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Cfd Analyses

In this study, a computational fluid dynamics (CFD)-based optimization process is used to change the contour of the airfoil near a suction-side cooling hole in order to improve its film effectiveness characteristics. An overview of the optimization process, which includes automated geometry, grid generation, and CFD analyses, is provided. From the results for the optimized geometry, it is clear that the detachment of the cooling jet is much reduced and the cooling jet spread in the spanwise direction is increased substantially. The new external contour was then tested in a low-speed wind tunnel to provide a direct measure of the predictive capability. Comparisons to verification test data indicate that good agreement was achieved for both pressure and film cooling effectiveness behavior. This study proves that despite its limitations, current Reynolds averaged Navier-Stokes (RANS) methodology can be used a viable design tool and lead to innovative concepts for improving film cooling effectiveness.

Improving Film Cooling Performance Using Airfoil Contouring

2006 ◽  
Author(s):  
Atul Kohli ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Suction Side ◽  
Design Tool ◽  
Optimization Process ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Cfd Analyses ◽  
Low Speed Wind Tunnel

In this study, a CFD-based optimization process is used to change the contour of the airfoil near a suction side cooling hole in order to improve its film effectiveness characteristics. An overview of the optimization process, which includes automated geometry, grid generation and CFD analyses is provided. From the results for the optimized geometry it is clear that the detachment of the cooling jet is much reduced and the cooling jet spread in the spanwise direction is increased substantially. The new external contour was then tested in a low-speed wind tunnel to provide a direct measure of the predictive capability. Comparisons to verification test data indicate that good agreement was achieved for both pressure and film cooling effectiveness behavior. This study proves that despite its limitations, current RANS methodology can be used a viable design tool and lead to innovative concepts for improving film cooling effectiveness.

Parametric Study on Anti-Vortex Film Cooling Hole Arrangements

2014 ◽  
Vol 660 ◽  
pp. 664-668
Author(s):  
Kamil Abdullah ◽  
Hazim Fadli Aminnuddin ◽  
Akmal Nizam Mohammed
Keyword(s):  
Film Cooling ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Vortex Pair ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Lateral Film ◽  
Lift Off

Film cooling has been extensively used to provide thermal protection for the external surface of the gas turbine blades. Numerous number of film cooling holes designs and arrangements have been introduced. The main motivation of these designs and arrangements are to reduce the lift-off effect cause by the counter rotating vortices (CRVP) produce by cylindrical cooling hole. One of the efforts is the introduction of newly found anti-vortex film cooling design. The present study focuses on anti-vortex holes arrangement consists of a main hole and pair of smaller holes. All three holes share a common inlet with the outlet of the smaller holes varies base on it relative position towards the main hole. Three anti-vortex holes arrangements have been considered; downstream anti-vortex hole arrangement (DAV), lateral anti-vortex hole arrangement (LAV), and upstream anti-vortex hole arrangement (UAV). In addition, a single hole (SH) film cooling has also been considered as the baseline. The investigation make used of ANSYS CFX software ver. 14. The investigations are made through Reynolds Average Navier Stokes analyses with the application of shear k-ε turbulence model. The results show that the anti-vortex designs produce significant improvement in term of film cooling effectiveness and distribution. The LAV arrangement shows the best film cooling effectiveness distribution among all considered cases and is consistent for all blowing ratios (BR). The results also unveil the formation of new vortex pair on both side of the primary hole CRVP. Interaction between the new vortices and the main CRVP structure reduce the lift off explaining the increased lateral film effectiveness.

scholarly journals A Detailed Study of Row-Trenched Holes at the Combustor Exit on Film-Cooling Effectiveness

2019 ◽  
Vol 23 (1) ◽  
pp. 246-252
Author(s):  
Ehsan Kianpour ◽  
Nor Azwadi Che Sidik
Keyword(s):  
Film Cooling ◽  
Navier Stokes ◽  
Spanwise Direction ◽  
Internal Cooling ◽  
Wall Surface ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
End Wall

Abstract To analyse the effects of cylindrical- and row-trenched cooling holes with an alignment angle of 90 degrees on the film-cooling effectiveness near the combustor end wall surface at a blowing ratio of 3.18, the current research was done. This research included a 3D representation of a Pratt and Whitney gas turbine engine, which was simulated and analysed with a commercial finite volume package FLUENT 6.2.26. The analysis was done with Reynolds-averaged Navier–Stokes turbulence model on internal cooling passages. This combustor simulator was combined with the interaction of two rows of dilution jets, which were staggered in the streamwise direction and aligned in the spanwise direction. In comparison with the baseline case of cooling holes, using row-trenched hole near the end wall surface increased the film-cooling effectiveness 44% in average.

Numerical Study on Film-Cooling Effectiveness for Various Film-Cooling Hole Schemes

2011 ◽  
Author(s):  
Sun-min Kim ◽  
Ki-Don Lee ◽  
Kwang-Yong Kim
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Influential Parameters

Film-cooling has been widely used as the important alternative to protect the turbine blade. Since the film-cooling hole geometry is one of the most influential parameters for film-cooling performance, various film-cooling hole schemes have been developed to increase cooling performance for the past few decades. In the present work, numerical analysis has been performed to investigate and to compare the film-cooling performance of various film-cooling hole schemes such as fan-shaped, crescent, louver, and dumbbell holes. For analyzes of the turbulent flow and film-cooling, three-dimensional Reynolds-averaged Navier-Stokes analysis has been performed with shear stress transport turbulence model. The validation of numerical results has been performed in comparison with experimental data. The flow characteristics and film-cooling performance for each hole shape have been investigated and evaluated in terms of local- and averaged film-cooling effectivenesses.

Effects of Surface Roughness and Near Hole Obstructions on Film Cooling Effectiveness

2007 ◽  
Author(s):  
Ruwan P. Somawardhana ◽  
David G. Bogard
Keyword(s):  
Surface Roughness ◽  
Film Cooling ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

For a film cooled turbine airfoil, significant degradation of adiabatic effectiveness can be caused by near-hole obstructions formed from deposition of contaminants. Since obstructions are a randomly occurring event, there are many variables to consider, namely shape, width, length, height, and position in relation to a film cooling hole. In addition to this, the level of overall surface roughness also must be considered. An investigation was conducted on obstruction characteristics for a single row of holes on the suction side of a simulated turbine vane. It was found that degradation due to near-hole obstructions only occurred when upstream obstructions were present. When directly upstream, degradation levels around 40% were observed and obstruction height was the dominating characteristic.

Improved Trench Film Cooling With Shaped Trench Outlets

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Habeeb Idowu Oguntade ◽  
Gordon E. Andrews ◽  
A. D. Burns ◽  
Derek B. Ingham ◽  
Mohammed Pourkashanian
Keyword(s):  
Flat Plate ◽  
Mass Flow ◽  
Film Cooling ◽  
Cross Flow ◽  
Suction Side ◽  
Experimental Results ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Vertical Slot ◽  
Cooling Hole

The influence of the shape of the downstream edge of trench film cooling hole outlets on film cooling effectiveness was investigated using CFD for flat plate film cooling. A 90 deg trench outlet wall with impinging 30 deg film cooling jets results in improved transverse film cooling effectiveness but produces a vertical slot jet into the cross flow, which is not the best aerodynamics for optimum film cooling. It was considered that improvements in the cooling effectiveness would occur if the trailing edge of the trench outlet produced a flow that was inclined in the direction of the crossflow. Beveled and filleted trench outlet shapes were investigated. The CFD predictions were shown to predict well the conventional sharp edged trench outlet experimental results for a flat plate geometry. The flat plate CFD predictions were also shown to predict the experimental results for trench cooling on the suction side of a turbine vane, where the local curvature was small relative to the trench width. The beveled and filleted trench outlets were predicted to suppress the vertical jet momentum and give a Coanda effect that allowed the cooling air to attach to the downstream wall surface. This produced an improved transverse spread of the coolant. Also, it was predicted that reducing the coolant mass flow per hole and increasing the number of rows of holes gave, for the same total coolant mass flow and the same surface area, a superior surface averaged cooling effectiveness.

The Effects of Obstructions on Film Cooling Effectiveness on the Suction Side of a Gas Turbine Vane

2006 ◽  
Author(s):  
Patricia Demling ◽  
David G. Bogard
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Suction Side ◽  
Temperature Profiles ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

The effects of obstructions on film cooling performance on a scaled-up 1st stage turbine vane will be discussed. Experimental results show that obstructions located upstream or inside of a film cooling hole will degrade adiabatic effectiveness up to 80% of the levels found with no obstructions. Downstream obstructions had little effect on performance. The location where the upstream obstructions ceased to degrade adiabatic effectiveness was determined and temperature profiles were constructed to determine how the upstream obstructions were affecting the mainstream and coolant flow.

Investigations of improved cooling effectiveness for ramp film cooling with compound angle film cooling jets

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Krishna Anand Vasu Devan Nair Girija Kumari ◽  
Parammasivam Kanjikoil Mahali
Keyword(s):  
Film Cooling ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Test Surface ◽  
Cooling Effectiveness ◽  
Content Type ◽  
Film Cooling Effectiveness ◽  
Ramp Test ◽  
Cooling Hole ◽  
Compound Angle

Purpose This paper aims to investigate the film cooling effectiveness (FCE) and mixing flow characteristics of the flat surface ramp model integrated with a compound angled film cooling jet. Design/methodology/approach Three-dimensional numerical simulation is performed on a flat surface ramp model with Reynolds Averaged Navier-Stokes approach using a finite volume solver. The tested model has a fixed ramp angle of 24° and a ramp width of two times the diameter of the film cooling hole. The coolant air is injected at 30° along the freestream direction. Three different film hole compound angles oriented to freestream direction at 0°, 90° and 180° were investigated for their performance on-ramp film cooling. The tested blowing ratios (BRs) are in the range of 0.9–2.0. Findings The film hole oriented at a compound angle of 180° has improved the area-averaged FCE on the ramp test surface by 86.74% at a mid-BR of 1.4% and 318.75% at higher BRs of 2.0. The 180° film hole compound angle has also produced higher local and spanwise averaged FCE on the ramp test surface. Originality/value According to the authors’ knowledge, this study is the first of its kind to investigate the ramp film cooling with a compound angle film cooling hole. The improved ramp model with a 180° film hole compound angle can be effectively applied for the end-wall surfaces of gas turbine film cooling.

Leading Edge Film Cooling: Computations and Experiments Including Density Effects

1996 ◽  
Author(s):  
Pingfan He ◽  
Dragos Licu ◽  
Martha Salcudean ◽  
Ian S. Gartshore
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Stokes Equations ◽  
Leading Edge ◽  
Variable Density ◽  
Navier Stokes ◽  
Cooling Effectiveness ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

The effect of varying coolant density on film cooling effectiveness for a turbine blade-model was numerically investigated and compared with experimental data. This model had a semi-circular leading edge with four rows of laterally-inclined film cooling orifices positioned symmetrically about the stagnation line. A curvilinear coordinate-based CFD code was developed and used for the numerical investigation. The code used a domain segmentation strategy in conjunction with general curvilinear grids to model the complex blade configuration. A multigrid method was used to accelerate the convergence rate. The time-averaged, variable-density, Navier-Stokes equations together with the energy or scalar equation were solved. Turbulence closure was attained by the standard k–ε model with a near-wall k model. Either air or CO2 was used as coolant in three cases of injection through single rows and alternatively staggered double raws of holes. Two different blowing rates were investigated in each case and compared with experimental data. The experimental results were obtained using a wind tunnel model, and the mass/heat analogy was used to determine the film cooling effectiveness. The higher density of the carbon dioxide coolant (approximately 1.5 times the density of air) in the isothermal mass injection experiments, was used to simulate the effects of injection of a colder air in the corresponding adiabatic heat transfer situation. Good agreement between calculated and measured film cooling effectiveness was found for low blowing ratio M ≤ 0.5 and the effect of density was not significant. At higher blowing ratio M > 1 the calculations consistently overpredict the measured values of film cooling effectiveness.

Sign in / Sign up

Export Citation Format

Share Document