Experimental Tool Temperature Distributions in Oblique and Orthogonal Cutting Using Chip Breaker Geometry Inserts

2005 ◽  
Vol 128 (2) ◽  
pp. 606-610 ◽  
Author(s):  
Rachid M’Saoubi ◽  
Hariharan Chandrasekaran
Keyword(s):  
Removal Rate ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Local Maximum ◽  
Cutting Parameters ◽  
Maximum Temperature ◽  
Tool Temperature ◽  
Chip Breaker ◽  
Suitable Combination ◽  
Lower Tool

Cutting tool temperature distribution was mapped using the infrared-charge-coupled device technique during machining of carbon steel SS2511 (∼AISI 3115) and stainless steel AISI 316L under oblique cutting conditions with chip breaker geometry inserts. Results indicated that the temperature on the rake surface was not uniform. Local maximum temperature points are present on the tool face at different locations, i.e., land, groove, backwall, and at the end of tool chip contact. Further investigation of the effect of cutting parameters on the tool temperature indicated that a suitable combination of cutting speed and feed resulted in a lower tool temperature for conditions of comparable material removal rate.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites

2013 ◽  
Author(s):  
Felicia Stan ◽  
Daniel Vlad ◽  
Catalin Fetecau
Keyword(s):  
Friction Coefficient ◽  
Cutting Force ◽  
Feed Rate ◽  
Normal Force ◽  
Polynomial Regression ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Force Model

This paper presents an experimental investigation of the cutting forces response during the orthogonal cutting of polytetrafluoroethylene (PTFE) and PTFE-based composites using the Taguchi method. Cutting experiments were conducted using the L27 orthogonal array and the effects of the cutting parameters (feed rate, cutting speed and rake angle) on the cutting force were analyzed using the S/N ratio response and the analysis of variance (ANOVA). Statistical models that correlate the cutting force with process variables were developed using ANOVA and polynomial regression. The variation of the apparent friction coefficient was analyzed with respect to tool geometry and the cutting process. The results indicated that cutting and thrust forces increase with increasing feed rate, and decrease with increasing rake angles from negative to positive values and increasing cutting speed. A power law relationship between the apparent friction coefficient and the normal force exerted by the chip on the tool-rake face was identified, the former decreasing with an increasing normal force.

Study on the Influence of Anisotropy on Cutting Performance of Aviation Aluminium Alloy 7050-T7451

2020 ◽  
Vol 990 ◽  
pp. 29-35
Author(s):  
Hui Wang ◽  
Ying Meng ◽  
Duo Duo Li ◽  
Xiu Li Fu ◽  
Qi Hang Shi
Keyword(s):  
Aluminium Alloy ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Performance ◽  
Rolled Sheet ◽  
Feed Speed ◽  
Aluminium Alloy 7050 ◽  
Degree Of Anisotropy ◽  
Forming Angle

Based on the hypocycloid theory, a highspeed orthogonal cutting simulation model was established. The cutting parameters (cutting speed, feed rate) and plane forming angle of the workpiece of aeronautical aluminium alloy 7050-T7451 pre-stretched rolled sheet were simulated and validated. The mapping relationship between cutting parameters, anisotropy and cutting performance was analyzed. The results show that the degree of anisotropy and the difficulty of material cutting are proportional to the forming angle, and the anisotropy decreases with the increase of cutting speed and the decrease of feed speed. Finally, the optimal cutting process range of aluminum alloy 7050-T7451 was obtained, which provides data support for highspeed cutting of anisotropic materials.

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

scholarly journals Finite Element Analysis and Statistical Optimization of End-Burr in Turning AA2024

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 276 ◽  
Author(s):  
Muhammad Asad ◽  
Hassan Ijaz ◽  
Waqas Saleem ◽  
Abdullah Mahfouz ◽  
Zeshan Ahmad ◽  
...  
Keyword(s):  
Finite Element ◽  
Orthogonal Cutting ◽  
Research Work ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Shear Zones ◽  
Statistical Analyses ◽  
Burr Formation ◽  
Pivot Point ◽  
Exit Edge

This contribution presents three-dimensional turning operation simulations exploiting the capabilities of finite element (FE) based software Abaqus/Explicit. Coupled temperature-displacement simulations for orthogonal cutting on an aerospace grade aluminum alloy AA2024-T351 with the conceived numerical model have been performed. Numerically computed results of cutting forces have been substantiated with the experimental data. Research work aims to contribute in comprehension of the end-burr formation process in orthogonal cutting. Multi-physical phenomena like crack propagation, evolution of shear zones (positive and negative), pivot-point appearance, thermal softening, etc., effecting burr formation for varying cutting parameters have been highlighted. Additionally, quantitative predictions of end burr lengths with foot type chip formation on the exit edge of the machined workpiece for various cutting parameters including cutting speed, feed rate, and tool rake angles have been made. Onwards, to investigate the influence of each cutting parameter on burr lengths and to find optimum values of cutting parameters statistical analyses using Taguchi’s design of experiment (DOE) technique and response surface methodology (RSM) have been performed. Investigations show that feed has a major impact, while cutting speed has the least impact in burr formation. Furthermore, it has been found that the early appearance of the pivot-point on the exit edge of the workpiece surface results in larger end-burr lengths. Results of statistical analyses have been successfully correlated with experimental findings in published literature.

scholarly journals Temperature Measurement by Visible Pyrometry: Orthogonal Cutting Application

2004 ◽  
Vol 126 (6) ◽  
pp. 931-936 ◽  
Author(s):  
N. Ranc ◽  
V. Pina ◽  
G. Sutter ◽  
S. Philippon
Keyword(s):  
High Speed ◽  
Orthogonal Cutting ◽  
Broad Band ◽  
Cutting Speed ◽  
Low Carbon Steel ◽  
Ccd Camera ◽  
Maximum Temperature ◽  
Low Carbon ◽  
Observation Area ◽  
Good Spatial Resolution

The working processes of metallic materials at high strain rate like forging, stamping and machining often induce high temperatures that are difficult to quantify precisely. In this work we, developed a high-speed broad band visible pyrometer using an intensified CCD camera (spectral range: 0.4 μm–0.9 μm). The advantage of the visible pyrometry technique is to limit the temperature error due to the uncertainties on the emissivity value and to have a good spatial resolution (3.6 μm) and a large observation area. This pyrometer was validated in the case of high speed machining and more precisely in the orthogonal cutting of a low carbon steel XC18. The cutting speed varies between 22 ms−1 and 60 ms−1. The experimental device allows one to visualize the evolution of the temperature field in the chip according to the cutting speed. The maximum temperature in the chip can reach 730°C and minimal temperature which can be detected is around 550°C.

FEA Simulation of the Influence of Cutting Parameters on Serrated Chip Formation in Machining Titanium Alloy Ti-6Al-4V

2012 ◽  
Vol 500 ◽  
pp. 152-156
Author(s):  
Zeng Hui Jiang ◽  
Ji Lu Feng ◽  
Xiao Ye Deng
Keyword(s):  
Titanium Alloy ◽  
Chip Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Element Model ◽  
Serrated Chip ◽  
Wide Range ◽  
Serrated Chip Formation ◽  
Fea Simulation

A finite element model of a two dimensional orthogonal cutting process is developed. The simulation uses standard finite software is able to solve complex thermo-mechanical problems. A thermo-visco-plastic model for the machined material and a rigid cutting tool were assumed. One of the main characteristic of titanium alloy is serrated shape for a wide range of cutting conditions. In order to understand the influence of cutting parameters on the chip formation when machining titanium alloy Ti-6Al-4V. The influence of the cutting speed,the cutting depth and the feed on the chip shape giving rise to segmented chips by strain localisation is respectively discussed.

Research on Microscopic Grain-Workpiece Interaction in Grinding through Micro-Cutting Simulation, Part 2: Factorial Study

2009 ◽  
Vol 76-78 ◽  
pp. 15-20 ◽  
Author(s):  
Lan Yan ◽  
Xue Kun Li ◽  
Feng Jiang ◽  
Zhi Xiong Zhou ◽  
Yi Ming Rong
Keyword(s):  
Cutting Force ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Shear Angle ◽  
Depth Of Cut ◽  
Specific Cutting Force ◽  
Single Grain

The grinding process can be considered as micro-cutting processes with irregular abrasive grains on the surface of grinding wheel. Single grain cutting simulation of AISI D2 steel with a wide range of cutting parameters is carried out with AdvantEdgeTM. The effect of cutting parameters on cutting force, chip formation, material removal rate, and derived parameters such as the specific cutting force, critical depth of cut and shear angle is analyzed. The formation of chip, side burr and side flow is observed in the cutting zone. Material removal rate increases with the increase of depth of cut and cutting speed. Specific cutting force decreases with the increase of depth of cut resulting in size effect. The shear angle increases as the depth of cut and cutting speed increase. This factorial analysis of single grain cutting is adopted to facilitate the calculation of force consumption for each single abrasive grain in the grinding zone.

scholarly journals Multi-Response Optimization in High-Speed Machining of Ti-6Al-4V Using TOPSIS-Fuzzy Integrated Approach

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1104 ◽  
Author(s):  
Adel T. Abbas ◽  
Neeraj Sharma ◽  
Saqib Anwar ◽  
Monis Luqman ◽  
Italo Tomaz ◽  
...  
Keyword(s):  
Titanium Alloys ◽  
High Speed ◽  
Removal Rate ◽  
Cutting Speed ◽  
Optimal Solution ◽  
Cutting Parameters ◽  
Integrated Approach ◽  
High Heat ◽  
Depth Of Cut ◽  
Cutting Processes

Titanium alloys are widely used in various applications including biomedicine, aerospace, marine, energy, and chemical industries because of their superior characteristics such as high hot strength and hardness, low density, and superior fracture toughness and corrosion resistance. However, there are different challenges when machining titanium alloys because of the high heat generated during cutting processes which adversely affects the product quality and process performance in general. Thus, optimization of the machining conditions while machining such alloys is necessary. In this work, an experimental investigation into the influence of different cutting parameters (i.e., depth of cut, cutting length, feed rate, and cutting speed) on surface roughness (Rz), flank wear (VB), power consumption as well as the material removal rate (MRR) during high-speed turning of Ti-6Al-4V alloy is presented and discussed. In addition, a backpropagation neural network (BPNN) along with the technique for order of preference by similarity to ideal solution (TOPSIS)-fuzzy integrated approach was employed to model and optimize the overall cutting performance. It should be stated that the predicted values for all machining outputs demonstrated excellent agreement with the experimental values at the selected optimal solution. In addition, the selected optimal solution did not provide the best performance for each measured output, but it achieved a balance among all studied responses.

Mechanism of Chip Deformation in Orthogonal Cutting the Wheel Steel

2008 ◽  
Vol 375-376 ◽  
pp. 26-30
Author(s):  
Kai Xue ◽  
Xiang Ming Xu ◽  
Gang Liu ◽  
Ming Chen
Keyword(s):  
Chip Formation ◽  
Feed Rate ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Chip Morphology ◽  
Cutting Parameters ◽  
Wheel Steel ◽  
Tool Geometry ◽  
Orthogonal Turning ◽  
On Chip

The chip formation and morphology are definitely affected by tool geometry and cutting parameters such as cutting speed, feed rate, and depth of cutting. An experiment investigation was presented to study the influence of tool geometry on chip morphology, and to clarify the effect of different cutting parameters on chip deformation in orthogonal turning the wheel steel. The result obtained in this study showed that tool geometry affected the chip morphology significantly; cutting speed was the most contributive factor in forming saw-tooth chip.

Sign in / Sign up

Export Citation Format

Share Document