Geometric Design of Three-Phalanx Underactuated Fingers

2005 ◽  
Vol 128 (2) ◽  
pp. 356-364 ◽  
Author(s):  
Lionel Birglen ◽  
Clément M. Gosselin
Keyword(s):  
Control Strategy ◽  
Degrees Of Freedom ◽  
Equilibrium Configuration ◽  
Contact Forces ◽  
Transmission Mechanism ◽  
Static Equilibrium ◽  
Object Size ◽  
Complex Control ◽  
Transmission Mechanisms ◽  
Grasp Stability

This paper studies the grasp stability of two classes of three-phalanx underactuated fingers with transmission mechanisms based on either linkages or tendons and pulleys. The concept of underactuation in robotic fingers—with fewer actuators than degrees of freedom—allows the hand to adjust itself to an irregularly shaped object without complex control strategy and sensors. With a n-phalanx finger, n contacts (one for each phalanx) are normally required to statically constrain the finger. However, some contact forces may be lacking due to either the transmission mechanism, or simply the object size and position. Thus, one may define an ith order equilibrium, when the finger is in static equilibrium with i missing contacts. In this paper, the case for which n=3 is studied with a particular emphasis on the cases for which i=1 and i=2. The fact that some contact forces do not appear or are negative, can lead in some cases to the ejection of the object from the hand, when no equilibrium configuration is achieved.

Equilibrium, Stability, and Robustness in Underactuated Grasping

2007 ◽  
Author(s):  
Gert A. Kragten ◽  
Just L. Herder
Keyword(s):  
Degrees Of Freedom ◽  
Equilibrium Configuration ◽  
Performance Measure ◽  
Equilibrium Stability ◽  
Equilibrium Conditions ◽  
Design Decisions ◽  
Grasp Stability ◽  
Movable Object ◽  
Passive Compliance ◽  
Freely Moving

This paper aims to develop a performance measure for underactuated grasping devices, which is useful in making design decisions to obtain an optimally performing device. Underactuated fingers, defined as having more degrees of freedom than degrees of actuation, intrinsically adapt their shape to the object. However, the equilibrium configuration and grasp forces of these fingers are not fully controllable, which may limit their performance. The grasp performance measure defined in this paper consists of three aspects: (1) the ability to grasp objects, which is limited by the equilibrium conditions and constraints of both the underactuated fingers and the freely movable object; (2) the grasp stability, which takes the passive compliance of the fingers into account; (3) the ability to oppose disturbance forces on the grasped object by passively adapting the frictional grasp forces. This measure was applied to optimize a planar grasping device with two underactuated fingers, each consisting of two phalanges, able to grasp freely moving circular objects.

Virtual Coupling Based Control Methodology for Lower Extremity Exoskeleton

2014 ◽  
Vol 556-562 ◽  
pp. 2365-2369 ◽  
Author(s):  
Jin Xiang Cui ◽  
Yan He Zhu ◽  
Ben Zhou Xu
Keyword(s):  
Lower Extremity ◽  
Control Strategy ◽  
Degrees Of Freedom ◽  
Virtual Prototype ◽  
Contact Forces ◽  
Admittance Control ◽  
Collaborative Simulation ◽  
Virtual Coupling ◽  
Control Methodology ◽  
Positional Control

As one of the most important examples of human-orientated system, the exoskeleton can improve the strength and endurance of the wearer. The exoskeleton has multi-degrees of freedom. As a result, a stable controller for the exoskeleton is difficult to design. The adoption of a purely positional control strategy may lead to large contact forces. Hence, an admittance control strategy is devised aimed at limiting both internal and contact forces. To verify the rationality and feasibility of the control strategy, we introduce a method utilizing virtual prototype and collaborative simulation.

scholarly journals Huanglongbing Model under the Control Strategy of Discontinuous Removal of Infected Trees

Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1164
Author(s):  
Weiwei Ling ◽  
Pinxia Wu ◽  
Xiumei Li ◽  
Liangjin Xie
Keyword(s):  
Infectious Disease ◽  
Global Stability ◽  
Control Strategy ◽  
Theoretical Basis ◽  
Dynamic Properties ◽  
Transmission Mechanism ◽  
Basic Reproductive Number ◽  
Reproductive Number ◽  
Vector Borne ◽  
Citrus Trees

By using differential equations with discontinuous right-hand sides, a dynamic model for vector-borne infectious disease under the discontinuous removal of infected trees was established after understanding the transmission mechanism of Huanglongbing (HLB) disease in citrus trees. Through calculation, the basic reproductive number of the model can be attained and the properties of the model are discussed. On this basis, the existence and global stability of the calculated equilibria are verified. Moreover, it was found that different I0 in the control strategy cannot change the dynamic properties of HLB disease. However, the lower the value of I0, the fewer HLB-infected citrus trees, which provides a theoretical basis for controlling HLB disease and reducing expenditure.

scholarly journals Torque Ripple Suppression of PMSM Based on Robust Two Degrees-of-Freedom Resonant Controller

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1015
Author(s):  
Mingfei Huang ◽  
Yongting Deng ◽  
Hongwen Li ◽  
Jing Liu ◽  
Meng Shao ◽  
...  
Keyword(s):  
Control Strategy ◽  
Measurement Errors ◽  
Degrees Of Freedom ◽  
Control Method ◽  
Torque Ripple ◽  
Current Loop ◽  
Two Degrees Of Freedom ◽  
Robust Stability Analysis ◽  
Resonant Controller ◽  
Testing Environments

This paper concentrates on a robust resonant control strategy of a permanent magnet synchronous motor (PMSM) for electric drivers with model uncertainties and external disturbances to improve the control performance of the current loop. Firstly, to reduce the torque ripple of PMSM, the resonant controller with fractional order (FO) calculus is introduced. Then, a robust two degrees-of-freedom (Robust-TDOF) control strategy was designed based on the modified resonant controller. Finally, by combining the two control methods, this study proposes an enhanced Robust-TDOF regulation method, named as the robust two degrees-of-freedom resonant controller (Robust-TDOFR), to guarantee the robustness of model uncertainty and to further improve the performance with minimized periodic torque ripples. Meanwhile, a tuning method was constructed followed by stability and robust stability analysis. Furthermore, the proposed Robust-TDOFR control method was applied in the current loop of a PMSM to suppress the periodic current harmonics caused by non-ideal factors of inverter and current measurement errors. Finally, simulations and experiments were performed to validate our control strategy. The simulation and experimental results showed that the THDs (total harmonic distortion) of phase current decreased to a level of 0.69% and 5.79% in the two testing environments.

Dynamic Analysis and Configuration Design of a Two-Component Wave-Energy Absorber

2012 ◽  
Author(s):  
Christophe Cochet ◽  
Ronald W. Yeung
Keyword(s):  
Wave Energy ◽  
Degrees Of Freedom ◽  
Outer Cylinder ◽  
Rigid Body Dynamics ◽  
Contact Forces ◽  
Energy Extraction ◽  
Energy Absorber ◽  
Compound Cylinder ◽  
Motion Study ◽  
Heave Motion

The wave-energy absorber being developed at UC Berkeley is modeled as a moored compound cylinder, with an outer cylinder sliding along a tension-tethered inner cylinder. With rigid-body dynamics, it is first shown that the surge and pitch degrees of freedom are decoupled from the heave motion. The heaving motion of the outer cylinder is analyzed and its geometric proportions (radii and drafts ratios) are optimized for wave-energy extraction. Earlier works of Yeung [1] and Chau and Yeung [2,3] are used in the present heave-motion study. The coupled surge-pitch motion can be solved and can provide the contact forces between the cylinders. The concept of capture width is used to characterize the energy extraction: its maximization leads to optimal energy extraction. The methodology presented provides the optimal geometry in terms of non-dimensional proportions of the device. It is found that a smaller radius and deeper draft for the outer cylinder will lead to a larger capture width and larger resulting motion.

Distribution of Wrench-Twist Duality in Over-Constrained Mechanisms

2003 ◽  
Vol 125 (1) ◽  
pp. 81-91 ◽  
Author(s):  
M. Fayet
Keyword(s):  
Degrees Of Freedom ◽  
Contact Forces ◽  
Simple Test ◽  
The Matrix

First, a procedure is presented in order to build the space of statically admissible wrenches. The matrix which generates them is obtained in an intrinsic way. It uses intersection of spaces for the edges (of the associated graph) and the new operation of “triangular projection” for the vertices. From this matrix, the choice of any set of indeterminable contact forces is achieved via a very simple test. This matrix allows to determine also all the possible degrees of freedom to add to the over-constrained mechanism in order to transform it into a non over-constrained one. Wrench-twist duality arises clearly in this last procedure.

Rolling Condition and Gyroscopic Moments in Curve Negotiations

2012 ◽  
Author(s):  
Ahmed A. Shabana ◽  
Martin B. Hamper ◽  
James J. O’Shea
Keyword(s):  
Coordinate System ◽  
Degrees Of Freedom ◽  
The Body ◽  
Contact Forces ◽  
Body Motion ◽  
Global Coordinate System ◽  
Gyroscopic Moment ◽  
Absolute Angular Velocity ◽  
Pure Rolling ◽  
The Stability

In vehicle system dynamics, the effect of the gyroscopic moments can be significant during curve negotiations. The absolute angular velocity of the body can be expressed as the sum of two vectors; one vector is due to the curvature of the curve, while the second vector is due to the rate of changes of the angles that define the orientation of the body with respect to a coordinate system that follows the body motion. In this paper, the configuration of the body in the global coordinate system is defined using the trajectory coordinates in order to examine the effect of the gyroscopic moments in the case of curve negotiations. These coordinates consist of arc length, two relative translations and three relative angles. The relative translations and relative angles are defined with respect to a trajectory coordinate system that follows the motion of the body on the curve. It is shown that when the yaw and roll angles relative to the trajectory coordinate system are constrained and the motion is predominantly rolling, the effect of the gyroscopic moment on the motion becomes negligible, and in the case of pure rolling and zero yaw and roll angles, the generalized gyroscopic moment associated with the system degrees of freedom becomes identically zero. The analysis presented in this investigation sheds light on the danger of using derailment criteria that are not obtained using laws of motion, and therefore, such criteria should not be used in judging the stability of railroad vehicle systems. Furthermore, The analysis presented in this paper shows that the roll moment which can have a significant effect on the wheel/rail contact forces depends on the forward velocity in the case of curve negotiations. For this reason, roller rigs that do not allow for the wheelset forward velocity cannot capture these moment components, and therefore, cannot be used in the analysis of curve negotiations. A model of a suspended railroad wheelset is used in this investigation to study the gyroscopic effect during curve negotiations.

Study of grasp-energy based optimal distribution of contact forces on a humanoid robotic hand during object grasp

Robotica ◽  
2021 ◽  
pp. 1-26
Author(s):  
Sourajit Mukherjee ◽  
Abhijit Mahapatra ◽  
Amit Kumar ◽  
Avik Chatterjee
Keyword(s):  
Optimization Algorithm ◽  
Degrees Of Freedom ◽  
Simulated Data ◽  
Performance Measure ◽  
Contact Forces ◽  
Contact Model ◽  
Robotic Hand ◽  
Net Energy ◽  
Optimal Distribution

Abstract A novel grasp optimization algorithm for minimizing the net energy utilized by a five-fingered humanoid robotic hand with twenty degrees of freedom for securing a precise grasp is presented in this study. The algorithm utilizes a compliant contact model with a nonlinear spring and damper system to compute the performance measure, called ‘Grasp Energy’. The measure, subject to constraints, has been minimized to obtain locally optimal cartesian trajectories for securing a grasp. A case study is taken to compare the analytical (applying the optimization algorithm) and the simulated data in MSC.Adams $^{^{\circledR}}$ , to prove the efficacy of the proposed formulation.

Smart Prosthetic Hand with Object Slippage Detection, Measurement, and Control

2014 ◽  
Vol 5 (3) ◽  
pp. 25-48
Author(s):  
Girish Sriram ◽  
Alex Jensen ◽  
Steve C. Chiu
Keyword(s):  
Control System ◽  
Control Strategy ◽  
Degrees Of Freedom ◽  
Sensory Feedback ◽  
Position Control ◽  
Tactile Feedback ◽  
Human Hand ◽  
Computing Platform ◽  
Emg Signal ◽  
A New Technique

The human hand along with its fingers possess one of the highest numbers of nerve endings in the human body. It thus has the capacity for the richest tactile feedback for positioning capabilities. This article shares a new technique of controlling slippage. The sensing system used for the detection of slippage is a modified force sensing resistor (FSR®). The control system is a fuzzy logic control algorithm with multiple rules that is designed to be processed on a mobile handheld computing platform and integrated/working alongside a traditional Electromyography (EMG) or Electroencephalography (EEG) based control system used for determining position of the fingers. A 5 Degrees of Freedom (DOF) hand, was used to test the slippage control strategy in real time. First a reference EMG signal was used for getting the 5 DOF hand to grasp an object, using position control. Then a slip was introduced to see the slippage control strategy at work. The results based on the plain tactile sensory feedback and the modified sensory feedback are discussed.

Sign in / Sign up

Export Citation Format

Share Document