Effects of Manufacturing Tolerances on Regenerative Exchanger Number of Transfer Units and Entropy Generation

2005 ◽  
Vol 128 (3) ◽  
pp. 585-598 ◽  
Author(s):  
Wei Shang ◽  
Robert W. Besant
Keyword(s):  
Entropy Generation ◽  
Flow Channel ◽  
Operating Conditions ◽  
Channel Diameter ◽  
Pressure Drops ◽  
Entropy Generation Number ◽  
Compact Heat Exchangers ◽  
Prime Concern ◽  
Manufacturing Tolerances ◽  
The Impact

A prime concern with the design of ultra-compact heat exchangers is the impact on performance of flow channel variations due to flow channel hydraulic diameter variations caused by manufacturing tolerances. This paper uses analytical methods to show that as the standard deviation in flow channel sizes, caused by manufacturing tolerances in a rotary regenerative exchanger, is increased compared to the average flow channel diameter the effective number of transfer units decreases. Depending on the operating conditions, the entropy generation number either increases or decreases with increasing flow channel size variations. These findings extend previous findings that showed that flow channel variations cause lower pressure drops and effectiveness.

scholarly journals Effects of non-uniform nanoparticle concentration on entropy generation

2021 ◽  
Vol 68 (1 Jan-Feb) ◽  
Author(s):  
Ahmer Mehmood ◽  
Sajid Khan ◽  
Muhammad Usman
Keyword(s):  
Entropy Production ◽  
Entropy Generation ◽  
Working Fluid ◽  
Physical Parameters ◽  
Bejan Number ◽  
Total Entropy ◽  
Entropy Generation Number ◽  
Self Similar Solution ◽  
Nanoparticles Concentration ◽  
The Impact

The entropy generation analysis of a thermal process is capable of determining the efficiency of that process and is therefore helpful to optimize the thermal system operating under various conditions. There are several ingredients upon which the phenomenon of entropy generation can depend, such as the nature of flow and the fluid, the assumed conditions, and the material properties of the working fluid. However, the dependence of entropy generation phenomenon upon such properties has so far not been fully realized, in view of the existing literature. On the other hand, based upon the existing studies, it has been established that the non-uniform concentration of nanoparticles in the base fluid does cause to enhance the heat transfer rate. Therefore, it is logical to investigate the entropy production under the impact of non-homogenous distribution of nanoparticles. Based upon this fact the aim of current study is to explore a comprehensive detail about the influence of non-homogeneous nanoparticles concentration on entropy production phenomenon by considering a laminar viscous flow past a moving continuous flat plate. Non-uniform concentration is considered in the nanofluid modeling in which the Brownian and thermophoretic diffusions are considered which impart significant effects on velocity and temperature profiles. An exact self-similar solution to this problem is observed to be possible and is reported. The effects of various controlling physical parameters such as Brinkman number, Schmidt number, Prandtl number, diffusion parameter, and concentration parameter on both local as well as total entropy generation number and Bejan number are elaborated by several graphs and Tables. The obtained results reveal a significant impact of all aforementioned parameters on entropy generation characteristics. It is observed that by a 20% increase in nanoparticles concentration the total entropy generation is increased up to 67% for a set of fixed values of remaining parameters.

Study of Entropy Generation in Heat Exchanger Tube With Multiple V Cuts in Perforated Twisted Tape Insert

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Bipin Kumar ◽  
Anil Kumar Patil ◽  
Siddharth Jain ◽  
Manoj Kumar
Keyword(s):  
Entropy Generation ◽  
Circular Tube ◽  
Operating Conditions ◽  
Entropy Generation Rate ◽  
Twisted Tape ◽  
Heat Exchanger Tube ◽  
Number Range ◽  
Entropy Generation Number ◽  
Twist Ratio ◽  
Exchanger Tube

The present work deals with the study of entropy generation in circular tube fitted with perforated twisted tape (PTT) insert with multiple V cuts. Experimental data pertaining to heat transfer and frictional losses are collected for solid twisted tape (STT), PTT, double V cut PTT, and PTT with multiple V cuts by varying the twist ratio in the range of 2–6 for the Reynolds number range of 2000–25,000. The entropy generation rate of heated tube with insert is found to be less than the smooth tube in most of the cases under similar operating conditions. The minimum value of entropy generation number corresponds to the PTT having twist ratio of 3.

Performance Evaluation of Heat Transfer Enhancement for Offset Strip Fins Used in Plate-Fin Heat Exchangers

2015 ◽  
Vol 137 (10) ◽  
Author(s):  
Yujie Yang ◽  
Yanzhong Li ◽  
Biao Si ◽  
Jieyu Zheng
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Entropy Generation ◽  
Heat Exchangers ◽  
Operating Conditions ◽  
Geometrical Parameters ◽  
Distribution Factor ◽  
Transfer Enhancement ◽  
Entropy Generation Number ◽  
Fin Thickness

In general, offset strip fin (OSF) used in plate-fin heat exchangers is able to provide a greater heat transfer coefficient than the plain fin with the same cross section, but it will also cause the increase of flow friction and pressure drop owing to the fin offset. A new parameter denoted by Ψ*, called relative entropy generation distribution factor, is proposed in this paper to comprehensively reflect the thermodynamic performance of different passage structures in plate-fin heat exchanger. This parameter physically represents relative changes of entropy generation and irreversibility, which are induced by both heat transfer and friction loss due to the utilization of OSF fins. The high magnitude of Ψ* represents a beneficial contribution of OSF with higher degree of the heat transfer enhancement. The proposed method is more reasonable and comprehensive than either the conventional augmentation entropy generation number, Ns,a, or the entropy generation distribution factor, ψ, to evaluate the heat transfer enhancement for OSF cores subject to various operating conditions. With the proposed method, the relative effects of the geometrical parameters of OSF fins, such as the fin thickness-to-height ratio α, fin density γ, and fin thickness-to-length ratio δ, on the heat transfer enhancement are discussed in detail. The results show that relatively small δ results in a better performance, while the parameter α or γ, which contribute to a higher degree of heat transfer enhancement of OSF fin, should be determined after the selection of the other two geometric parameters.

scholarly journals Study of Entropy Generation with Multi-Slip Effects in MHD Unsteady Flow of Viscous Fluid Past an Exponentially Stretching Surface

Symmetry ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 426 ◽  
Author(s):  
Sajjad Haider ◽  
Adnan Saeed Butt ◽  
Yun-Zhang Li ◽  
Syed Muhammad Imran ◽  
Babar Ahmad ◽  
...  
Keyword(s):  
Differential Equations ◽  
Viscous Fluid ◽  
Entropy Generation ◽  
Slip Flow ◽  
Physical Parameters ◽  
Bejan Number ◽  
Entropy Generation Number ◽  
Linear Differential ◽  
Exponentially Stretching ◽  
The Impact

The current study aims to probe the impacts of entropy in a hydromagnetic unsteady slip flow of viscous fluid past an exponentially stretching sheet. Appurtenant similarity variables are employed to transmute the governing partial differential equations into a system of non-linear differential equations, which are analytically solved by utilizing the homotopy analysis method (HAM). Moreover, a shooting technique with fourth–fifth order Runge–Kutta method is deployed to numerically solve the problem. The impact of the physical parameters that influence the flow and heat transmission phenomena are sketched, tabulated and discussed briefly. Additionally, the impact of these parameters on entropy generation is thoroughly discussed by plotting graphs of the local entropy generation number and the Bejan number.

Analysis of Microchannel Heat Sink Performance for Electronics Cooling Based on Thermodynamics

2006 ◽  
Author(s):  
Hessamoddin Abbassi ◽  
Mohammad H. Saidi ◽  
Pouya Zageneh Kazemi
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Entropy Generation ◽  
Heat Sink ◽  
Closed Form Solution ◽  
Electronics Cooling ◽  
Bejan Number ◽  
Microchannel Heat Sink ◽  
Entropy Generation Number ◽  
The Impact

Present investigation analyzes the issue of entropy generation in a uniformly heated microchannel heat sink (MCHS). Analytical approach used to solve forced convection problem across MCHS, is porous medium model based on modified Darcy equation for fluid flow and two-equation model for heat transfer between solid and fluid phases. Furthermore, closed form solution of velocity distribution is employed to capture z-direction velocity gradient of flow, which plays a salient role on entropy generation through fluid flow. Analytical expressions for total and thermal entropy generation number (stems from heat transfer), and Bejan number are derived and cast into dimensionless form using velocity and temperature distributions. Besides, entropy generation characteristics in MCHS and the impact of various influential parameters on entropy production have been investigated. Finally, In order to examine the accuracy of analysis, the results of thermal evaluation are compared to one of the previous investigations conducted for thermal optimization of MCHS.

scholarly journals Spectral Quasi-Linearization Method for Non-Darcy Porous Medium with Convective Boundary Condition

Entropy ◽  
2019 ◽  
Vol 21 (9) ◽  
pp. 838 ◽  
Author(s):  
R. A. Alharbey ◽  
Hiranmoy Mondal ◽  
Ramandeep Behl
Keyword(s):  
Boundary Layer ◽  
Porous Medium ◽  
Angular Velocity ◽  
Entropy Generation ◽  
Micropolar Fluid ◽  
Material Parameter ◽  
Numerical Solutions ◽  
Linearization Method ◽  
Entropy Generation Number ◽  
The Impact

The boundary layer micropolar fluid over a horizontal plate embedded in a non-Darcy porous medium is investigated in this study. This paper is solely focused on contributions oriented towards the application of micropolar fluid flow over a stretching sheet. The prime equations are renewed to ordinary differential equations with the assistance of similarity transformation; they are then subsequently solved numerically using the spectral quasi-linearization method (SQLM) for direct Taylor series expansions that can be applied to non-linear terms in order to linearize them. The spectral collocation approach is then applied to solve the resulting linearized system of equations. The paper acquires realistic numerical explanations for rapidly convergent solutions using the spectral quasi-linearization method. Convergence of the numerical solutions was monitored using the residual error of the PDEs. The validity of our model is established using error analysis. The impact of different geometric parameters on angular velocity, temperature, and entropy generation numbers are presented in graphs. The results show that the entropy generation number decelerates with an increase in Reynolds number and Brinkmann number. The velocity profile increases with the increasing material parameter. The results indicate that the fluid angular velocity decreases throughout the boundary layer for increasing values of the material parameter.

Truck Tire Operating Temperatures on Flat and Curved Test Surfaces

2005 ◽  
Vol 33 (3) ◽  
pp. 156-178 ◽  
Author(s):  
T. J. LaClair ◽  
C. Zarak
Keyword(s):  
Flat Surface ◽  
Operating Temperature ◽  
Operating Conditions ◽  
Load Pressure ◽  
Truck Tire ◽  
Endurance Testing ◽  
Operating Temperatures ◽  
The Impact ◽  
Tread Rubber ◽  
Cylindrical Test

Abstract Operating temperature is critical to the endurance life of a tire. Fundamental differences between operations of a tire on a flat surface, as experienced in normal highway use, and on a cylindrical test drum may result in a substantially higher tire temperature in the latter case. Nonetheless, cylindrical road wheels are widely used in the industry for tire endurance testing. This paper discusses the important effects of surface curvature on truck tire endurance testing and highlights the impact that curvature has on tire operating temperature. Temperature measurements made during testing on flat and curved surfaces under a range of load, pressure and speed conditions are presented. New tires and re-treaded tires of the same casing construction were evaluated to determine the effect that the tread rubber and pattern have on operating temperatures on the flat and curved test surfaces. The results of this study are used to suggest conditions on a road wheel that provide highway-equivalent operating conditions for truck tire endurance testing.

A NEW WELDING MATERIAL FOR REGENERATION IN THE WELDING TECHNOLOGY BASED ON NICKEL. ANALYSIS OF THE COMPOSITION AND PROPERTIES OF DEFORMABLE HEAT-RESISTANT HIGH-CHROMIUM NICKEL-BASED ALLOYS FOR WELDED PARTS. ANALYSIS OF EXISTING FUELLING STATIONS TYPES AND VEHICLES USING HYDROGEN, HYDROGEN PRODUCTION AND STORING METHODS

2019 ◽  
pp. 43-48
Author(s):  
Ben Nengjun ◽  
Zhou Pengfei ◽  
Oleksandr Labartkava ◽  
Mykhailo Samokhin
Keyword(s):  
Rare Earth ◽  
High Temperature ◽  
Nickel Alloys ◽  
Total Content ◽  
Operating Conditions ◽  
High Temperature Strength ◽  
High Chromium ◽  
Salt Corrosion ◽  
Tcp Phases ◽  
The Impact

This work involves an analysis of high-chromium high-temperature deformable wieldable nickel alloys for use in GTE repair assemblies. It is shown that the alloys EP868 (VZh98) and Haynes 230 can be used in welded assemblies with an operating temperature of 800-1100 °C. The alloys Nimonic 81, Nimonic 91, IN 935, IN 939, and Nicrotan 2100 GT also have a high potential for use in welded assemblies. They are characterized by a combination of good weldability, high-temperature strength, and resistance to scaling. There have been conducted studies on high-temperature salt corrosion of model nickel alloys. They allowed establishing the patterns of the impact of base metal alloying with chromium, aluminum, titanium, cobalt, tungsten, molybdenum, niobium, tantalum and rare earth metals on the critical temperature of the start of salt corrosion Tcor and the alloy mass loss. It has been established that alloys with a moderate concentration (13-16%) of chromium can possess satisfactory hightemperature corrosion resistance (HTC resistance) under the operating conditions of ship GTE. The HTC resistance of CrAl-Ti alloys improves upon reaching the ratio Ti/Al ˃ 1. Meanwhile, the ratio Ti/Al ˂ 1 promotes the formation of corrosion products with low protective properties. The positive effect of tantalum on the HTC resistance of alloys is manifested at higher test temperatures than that of titanium, and the total content of molybdenum and tungsten in alloys is limited by the condition 8Mo2 – 2W2 = 89. The presence of refractory elements stabilizes the strengthening phase and prevents formation of the ɳ-phase. However, their excess promotes formation of the embrittling topologically close packed (TCP) phases and boundary carbides of an unfavorable morphology. Based on the studies of the HTC resistance, there has been identified a class of model high-temperature corrosionresistant nickel alloys with a moderate or high chromium content (30%), Ti/Al ˃ 1, and a balanced content of refractory and rare-earth elements.

Application of vacuum belt press filters for cane mud filtration and performance comparison with rotary filters

2014 ◽  
pp. 298-301 ◽  
Author(s):  
Arnaud Petit
Keyword(s):  
Electricity Consumption ◽  
Performance Comparison ◽  
Operating Conditions ◽  
Vacuum Filter ◽  
Sugar Mill ◽  
Belt Press ◽  
Vacuum Belt ◽  
And Performance ◽  
Mud Filtration ◽  
The Impact

Bois-Rouge factory, an 8000 t/d cane Reunionese sugarcane mill, has fully equipped its filtration station with vacuum belt press filters since 2010, the first one being installed in 2009. The present study deals with this 3-year experience and discusses operating conditions, electricity consumption, performance and optimisation. The comparison with the more classical rotary drum vacuum filter station of Le Gol sugar mill highlights advantages of vacuum belt press filters: high filtration efficiency, low filter cake mass and sucrose content, low total solids content in filtrate and low power consumption. However, this technology needs a mud conditioning step and requires a large amount of water to improve mud quality, mixing of flocculant and washing of filter belts. The impact on the energy balance of the sugar mill is significant. At Bois-Rouge mill, studies are underway to reduce the water consumption by recycling low d.s. filtrate and by dry cleaning the filter belts.

Influence of temperature and humidity on the angle of repose of wood bulk materials

2016 ◽  
Author(s):  
И.В. Бачериков ◽  
Б.М. Локштанов
Keyword(s):  
Field Experiments ◽  
Bulk Material ◽  
Average Particle Size ◽  
Operating Conditions ◽  
Angle Of Repose ◽  
Wood Dust ◽  
Average Particle ◽  
Bulk Materials ◽  
Technical Literature ◽  
The Impact

При проектировании открытых и закрытых хранилищ измельченных сыпучих материалов древесных материалов, таких как щепа и опилки, большое значение имеет угол естественного откоса (статический и динамический) этих материалов. В технической литературе приводятся противоречивые сведения о величине этих углов, что приводит к ошибкам при проектировании складов. В справочных данных не учитываются условия, в которых эксплуатируются емкости для хранения сыпучих материалов, свойства и состояние этих сыпучих материалов. В свою очередь, ошибки при проектировании приводят к проблемам (зависание, сводообразование, «затопление» и т. д.) и авариям при эксплуатации бункеров и силосов на производстве. В статье представлены сведения, посвященные влиянию влажности и температуры на угол естественного откоса сыпучих материалов. На основании лабораторных и натурных экспериментов, проведенных с помощью специально разработанных методик и установок, была скорректирована формула для определения углов естественного откоса (статического и динамического) для измельченных древесных материалов в зависимости от их фракционного и породного состава, влажности (абсолютной и относительной) и температуры. При помощи скорректированной формулы можно определить угол естественного откоса древесных сыпучих материалов со среднегеометрическим размером частицы от 0,5 мм до 15 мм (от древесной пыли до технологической щепы) в различных производственных условиях. Статья может быть полезна проектировщикам при расчете угла наклона граней выпускающей воронки бункеров и силосов предприятий лесной отрасли и целлюлозо-бумажной промышленности. In the design of open and closed storage warehouses chopped wood materials for bulk materials such as wood chips and sawdust, great importance has an angle of repose (static and dynamic) of these materials. In the technical literature are conflicting reports about the magnitude of these angles, which leads to errors in the design of warehouses. In the referencesdoes not take into account the conditions under which operated capacities for storage of bulk materials, and properties and condition of the bulk material. The design errors lead to problems (hanging, arching, «flooding», etc.) and accidents in the operation of hoppers and silos at the mills. The article provides information on the impact of humidity and temperature on the angle of repose of granular materials. On the basis of laboratory and field experiments, conducted with the help of specially developed techniques and facilities has been adjusted formula for determining the angle of repose (static and dynamic) for the shredded wood materials depending on their fractional and species composition, humidity (absolute and relative) and temperature. It is possible, by using the corrected formula, to determine the angle of repose of loose wood materials with average particle size of from 0.5 mm to 15 mm (wood dust to pulpchips) in various operating conditions. The article can be helpful to designers in the calculation of the angle of inclination of the funnel faces produces bunkers and silos forest industries and pulp and paper industry.

Sign in / Sign up

Export Citation Format

Share Document