Investigation on Effect of Surface Roughness Pattern to Drag Force Reduction Using Rotary Rheometer

2005 ◽  
Vol 128 (1) ◽  
pp. 131-138 ◽  
Author(s):  
Chen Haosheng ◽  
Chen Darong ◽  
Li Yongjian
Keyword(s):  
Surface Roughness ◽  
Drag Force ◽  
Smooth Surface ◽  
Side Wall ◽  
Viscous Force ◽  
Longitudinal Groove ◽  
Pressure Drag ◽  
Side Walls ◽  
Force Reduction ◽  
Effect Of Surface

A drag force reduction experiment is performed on polyoxyethylene (PEO) water solution using a rotary rheometer. Longitudinal, transverse, and isotropic grooves are notched on the rotor’s surface to investigate the effect of surface roughness patterns. The experiment results show that higher drag force is generated on the surface with transverse grooves compared with the drag force on a smooth surface, while lower drag force is generated on the surface with longitudinal grooves. The drag force on the surface with isotropic grooves is between them. Forces on the side wall of the grooves play important roles in drag force reduction. They are numerically analyzed based on the Navier-Stokes equation using the finite volume method. The viscous force on the groove’s bottom plane is far less than the force on the corresponding plane of the smooth surface, but the drag force on the groove’s surface is compensated either by the pressure drag on the side walls of the transverse groove or by the viscous force on the side walls of the longitudinal groove. The pressure drag on side wall of transverse groove is always higher than the viscous force on side wall of longitudinal groove. The numerical results cope with the experiment results that only the surface with longitudinal grooves can reduce the drag force.

Effect of Surface Roughness on Fouling of Calcium Carbonate: An Experimental Investigation

2010 ◽  
Author(s):  
M. Izadi ◽  
D. K. Aidun ◽  
P. Marzocca ◽  
H. Lee
Keyword(s):  
Surface Roughness ◽  
Calcium Carbonate ◽  
Rough Surface ◽  
Smooth Surface ◽  
Rough Surfaces ◽  
Operating Conditions ◽  
Tubular Heat Exchanger ◽  
Analytical Microscopy ◽  
Deposit Layer ◽  
Effect Of Surface

The effect of surface roughness on the fouling behavior of calcium carbonate is experimentally investigated. The real operating conditions of a tubular heat exchanger are simulated by performing prolonged experiments with duration of 3 to 7 days. The solution used is a mixture of sodium bicarbonate and calcium chloride in de-ionized water with the concentration of 0.4 g/l of each. An on-line fouling evaluation system was developed such that the fouling resistance for a selected solution could be measured in real time. The experiments are repeated with the same procedure for 90/10 Cu/Ni tubes with different internal surface roughness. After the experiment the surface is analyzed by analytical microscopy to investigate the morphology of the deposit layer. Comparison of the experimental results of smooth and rough surfaces shows that a combination of aragonite and calcite polymorphs are formed on rough surface while only dendritic porous aragonite crystals are formed on smooth surface. Accordingly, the deposit layer formed on rough surface is denser and has a higher thermal resistance comparing to that formed on smooth surface. The fouling factor-time curves of smooth and rough surfaces obtained by the current experimental study agree with the results found by the analytical microscopy of the surface and show higher fouling resistances for rough surface. Experimental data is significantly important for the design, and formulating operating, and cleaning schedules of the equipment.

Numerical Analysis on the Effect of Transverse Surface Roughness in Non-Newtonian Fluid Lubrication

2005 ◽  
Author(s):  
Haosheng Chen ◽  
Yongjian Li ◽  
Darong Chen ◽  
Jiadao Wang
Keyword(s):  
Surface Roughness ◽  
Drag Force ◽  
Newtonian Fluid ◽  
Roughness Height ◽  
Navier Stokes ◽  
Lubricant Thickness ◽  
Navier Stokes Equation ◽  
Obvious Effect ◽  
Total Drag ◽  
Pressure Drag

To analyze non-Newtonian fluid lubrication with the effect of large surface roughness amplitude, Navier-Stokes equation is used and a finite volume method is adopted to acquire the lubrication results of an inclined slider model. The numerical results show that the pressure mutation occurs at the edges of surface roughness. When the roughness height is more than 1% lubricant thickness, the surface roughness takes an obvious effect on the lubrication results. The pressure drag increase as the roughness height increases, the friction drag decreases and the total drag force keeps constant. When the roughness height is more than 10% lubricant thickness, the friction force begins to increase and the total drag force increases rapidly. Non-Newtonian fluid affects the lubrication results more greatly than the surface roughness height does, but it does not affect the variation process caused by different surface roughness.

Adhesion and Autohesion of Rubber Compounds: Effect of Surface Roughness

1995 ◽  
Vol 68 (1) ◽  
pp. 13-25 ◽  
Author(s):  
A. N. Gent ◽  
S-M. Lai
Keyword(s):  
Surface Roughness ◽  
Smooth Surface ◽  
Peel Strength ◽  
The Other ◽  
Rubber Compound ◽  
Rubber Compounds ◽  
Roughened Surface ◽  
Styrene Butadiene ◽  
Effect Of Surface ◽  
Strength Of Adhesion

Abstract Sheets of various rubber compounds were pre-molded using different mold surfaces: Mylar film, smooth steel, and roughened steel. Two sheets of the same compound were then bonded together by crosslinking them in contact. Measurements of peel strength were carried out over a range of temperatures from −40°C to + 130°C. When an uncured sheet was crosslinked in contact with a smooth fully-cured sheet, the peel strength was generally lower than the tear strength of either sheet and the degree of interlinking was inferred to be only about one-half of the degree of crosslinking. On the other hand, when a sheet was cured in contact with a rough surface the strength of adhesion was 2× to 3× higher than with a smooth surface, probably because of increased area for bonding. Thus, when a rubber compound was cured in contact with a fully-cured sheet having a roughened surface, the two effects largely cancelled out and the resultant bond was about as strong as the material itself. Examples are given for carbon-black-filled and unfilled compounds based on polybutadiene, a styrene-butadiene copolymer, and natural rubber.

The effect of surface roughness on AES depth profile.

Shinku ◽  
1987 ◽  
Vol 30 (10) ◽  
pp. 793-798 ◽  
Author(s):  
Masao HIRASAKA ◽  
Masao HASHIBA ◽  
Toshiroh YAMASHINA
Keyword(s):  
Surface Roughness ◽  
Depth Profile ◽  
Effect Of Surface

Innovative approaches in the organization of closed waste-free production of organic pork using cultural and natural agricultural land

2020 ◽  
pp. 15-25
Author(s):  
Volodymyr Ivanov ◽  
Andrii Onyshchenko ◽  
Liudmyla Ivanova ◽  
Liudmyla Zasukha ◽  
Valerii Hryhorenko
Keyword(s):  
Agricultural Land ◽  
Side Wall ◽  
Front Wall ◽  
Lower Edge ◽  
Metal Mesh ◽  
Two Phase ◽  
Transparent Plastic ◽  
Pork Production ◽  
Young Pigs ◽  
Side Walls

The mobile house for two-phase litter rearing piglets was developed in the conditions of pasture their housing, the feature of which is that its side walls and roof are made in the form of two similar in shape and length of arched panels. In the back wall of the inner shield is a litter box, a self-feeder for piglets, a feed unit for a sow and a wicket, and in the front wall of the outer shield are doors with a wicket. Along with this, all walls and the roof of the litter box are made of transparent plastic, and the wall located near the self-feeding trough is also made perforated. In addition, the lower edge of the side wall of the inner arch-shaped shield has slides in which the lower edge of the side wall of the outer arc-shaped shield is inserted. A house with transformable fences has been developed to rear the young pigs. The structural feature of the house is the presence on the outside of the walls of the bobbins with a metal mesh edged at the bottom with a flexible sleeve. In order to ensure the conditions of gentle etching of the vegetation cover and to prevent damage to the turf of the pasture, the house can be completed with another type of hedge consisting of two hinged sections with doors on each side of the fence. In addition, the horizontal wings are rigidly attached to the hedge and connected by a metal mesh around the perimeter, the size of the cells of which ensures that the grass is eaten but prevents the turf of the pasture from being undermined. The developed devices for camp-pasture and feeding of maternal stock, suckling pigs, weaning pigs, repair and fattening pigs are well suited for year-round closed non-waste organic pork production using cultural and natural agricultural land. Key words: housing, feeding, devices, sows, piglets, young animals, pasture, organic pork.

Sign in / Sign up

Export Citation Format

Share Document