Meso Scale Pulsating Jets for Electronics Cooling

2005 ◽  
Vol 127 (4) ◽  
pp. 503-511 ◽  
Author(s):  
Jivtesh Garg ◽  
Mehmet Arik ◽  
Stanton Weaver ◽  
Todd Wetzel ◽  
Seyed Saddoughi
Keyword(s):  
Heat Transfer ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Coefficient Of Performance ◽  
Small Scale ◽  
Driving Voltage ◽  
Driving Frequency ◽  
Air Velocity ◽  
Maximum Heat ◽  
Meso Scale

Microfluid devices are conventionally used for boundary layer control in many aerospace applications. Synthetic jets are intense small-scale turbulent jets formed from periodic entrainment and expulsion of the fluid in which they are embedded. The jets can be made to impinge upon electronic components thereby providing forced convection impingement cooling. The small size of these devices accompanied by the high exit air velocity provides an exciting opportunity to significantly reduce the size of thermal management hardware in electronics. A proprietary meso scale synthetic jet designed at GE Global Research is able to provide a maximum air velocity of 90m∕s from a 0.85 mm hydraulic diameter rectangular orifice. An experimental study for determining the cooling performance of synthetic jets was carried out by using a single jet to cool a thin foil heater. The heat transfer augmentation caused by the jets depends on several parameters, such as, driving frequency, driving voltage, jet axial distance, heater size, and heat flux. During the experiments, the operating frequency for the jets was varied between 3.4 and 5.4 kHz, while the driving voltage was varied between 50 and 90VRMS. Two different heater powers, corresponding to approximately 50 and 80 °C, were tested. A square heater with a surface area of 156mm2 was used to mimic the hot component and detailed temperature measurements were obtained with a microscopic infrared thermal imaging technique. A maximum heat transfer enhancement of approximately 10 times over natural convection was measured. The maximum measured coefficient of performance was approximately 3.25 due to the low power consumption of the synthetic jets.

Micro Fluidic Jets for Thermal Management of Electronics

Volume 4 ◽  
2004 ◽  
Author(s):  
Jivtesh Garg ◽  
Mehmet Arik ◽  
Stanton Weaver ◽  
Seyed Saddoughi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heated Surface ◽  
Turbulent Jets ◽  
Harmonic Signal ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Small Scale ◽  
Air Cooling ◽  
Infrared Thermal Imaging

Micro fluidics devices are conventionally used for boundary layer control in many aerospace applications. Synthetic Jets are intense small scale turbulent jets formed from entrainment and expulsion of the fluid in which they are embedded. The idea of using synthetic jets in confined electronic cooling applications started in late 1990s. These micro fluidic devices offer very efficient, high magnitude direct air-cooling on the heated surface. A proprietary synthetic jet designed in General Electric Company was able to provide a maximum air velocity of 90 m/s from a 1.2 mm hydraulic diameter rectangular orifice. An experimental study for determining the thermal performance of a meso scale synthetic jet was carried out. The synthetic jets are driven by a time harmonic signal. During the experiments, the operating frequency for jets was set between 3 and 4.5 kHz. The resonance frequency for a particular jet was determined through the effect on the exit velocity magnitude. An infrared thermal imaging technique was used to acquire fine scale temperature measurements. A square heater with a surface area of 156 mm2 was used to mimic the hot component and extensive temperature maps were obtained. The parameters varied during the experiments were jet location, driving jet voltage, driving jet frequency and heater power. The output parameters were point wise temperatures (pixel size = 30 μm), and heat transfer enhancement over natural convection. A maximum of approximately 8 times enhancement over natural convection heat transfer was measured. The maximum coefficient of cooling performance obtained was approximately 6.6 due to the low power consumption of the synthetic jets.

Predicting Heat Transfer From Unsteady Synthetic Jets

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Mehmet Arik ◽  
Tunc Icoz
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Jet Impingement ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Operating Conditions ◽  
Small Scale ◽  
Wide Range ◽  
The Heat Transfer Coefficient

Synthetic jets are piezo-driven, small-scale, pulsating devices capable of producing highly turbulent jets formed by periodic entrainment and expulsion of the fluid in which they are embedded. The compactness of these devices accompanied by high air velocities provides an exciting opportunity to significantly reduce the size of thermal management systems in electronic packages. A number of researchers have shown the implementations of synthetic jets on heat transfer applications; however, there exists no correlation to analytically predict the heat transfer coefficient for such applications. A closed form correlation was developed to predict the heat transfer coefficient as a function of jet geometry, position, and operating conditions for impinging flow based on experimental data. The proposed correlation was shown to predict the synthetic jet impingement heat transfer within 25% accuracy for a wide range of operating conditions and geometrical variables.

Heat Transfer Measurements of Impinging Synthetic Air Jet

2007 ◽  
Author(s):  
Alan McGuinn ◽  
Tadhg S. O’Donovan ◽  
Darina B. Murray
Keyword(s):  
Heat Transfer ◽  
Flow Characteristics ◽  
Impinging Jets ◽  
Copper Plate ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Driving Frequency ◽  
Promising Alternative ◽  
Air Jet ◽  
Cooling Effects

The implementation of synthetic jets for use in the cooling of electronics is a relatively new technology. It is well established that effective rates of cooling can be achieved using conventional steady flow impinging jets. However it has been shown that synthetic jets can deliver similar cooling effects without the need for an air supply system and therefore represent an extremely promising alternative for thermal management applications. A study has been undertaken of the heat transfer distribution to an impinging synthetic jet flow. The jet is directed at a heated copper plate, which approximates a uniform wall temperature. Nusselt number profiles generated by the synthetic jet for various Reynolds numbers and heights above the plate were obtained. Time varying velocity measurements were also carried out to provide information about the flow characteristics of the synthetic jet and to aid with evaluation of the heat transfer data. For continuous jets mean heat transfer distributions have been shown to have a direct relation to jet velocity profiles, however, for synthetic jets fluctuations in local heat flux illustrate a significant dependence on the driving frequency.

An Experimental Study of Impinging Synthetic Jets for Heat Transfer Augmentation

2015 ◽  
Vol 23 (03) ◽  
pp. 1550024 ◽  
Author(s):  
Omidreza Ghaffari ◽  
Muhammad Ikhlaq ◽  
Mehmet Arik
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Vertical Surface ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Coefficient Of Performance ◽  
Stroke Length ◽  
Cooling Performance ◽  
Circular Jets ◽  
Number Formula

According to recent trends in the field of miniature electronics, the need for compact cooling solutions compatible with very thin profiles and small footprint areas is inevitable. Impinging synthetic jets are recognized as a promising technique for cooling miniature surfaces like laptops, tablets, smart phones and slim TV systems. Effect of jet to cooled surface spacing is crucial in cooling performance as well as predicting Nusselt number for such spacing. An experimental study has been performed to investigate the cooling performance of two different synthetic jets actuated with piezoelectric actuators cooling over a vertical surface. Results showed that a major degradation of heat transfer when jets are close to the surface is occurred. Slot synthetic jets showed a better performance in terms of coefficient of performance (COP) than semi-confined circular jets for small jet to surface spacing. Later, a correlation is proposed for predicting Nu number for a semi-confined circular synthetic jet accounting the effects of Re number ([Formula: see text]), jet-to-surface spacing ([Formula: see text] and [Formula: see text]) and the stroke length ([Formula: see text] and [Formula: see text]). It is found that correlation can provide predictions with an [Formula: see text] value of over 98%.

Interaction of Synthetic Jet Cooling Performance With Gravity and Buoyancy Driven Flows

2007 ◽  
Author(s):  
Mehmet Arik ◽  
Yogen Utturkar ◽  
Mustafa Gursoy
Keyword(s):  
Heat Transfer ◽  
Heat Dissipation ◽  
Cross Flow ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Jet Cooling ◽  
Impingement Heat Transfer ◽  
Buoyancy Driven Flows ◽  
Experimental Findings ◽  
Meso Scale

Meso scale cooling devices have been of interest for low form factor, tight space, and high COP thermal management problems. A candidate meso scale device, known as synthetic jets, operates with micro fluidic principles and disturbs the boundary layer causing significant heat transfer over conventional free convective heat transfer in air. Previous papers have dealt with the impingement and cross flow, but did not study mixed convection for synthetic jet with natural convection. In the present study, we discuss the results of an experimental study to investigate the interplay between jet orientations with respect to gravity, elevated temperature conditions, and synthetic jet heat dissipation capacity. Experiments were performed by placing synthetic at different positions around a square, 25.4mm heated flat surface. The flow physics behind the experimental findings is discussed. It is found that impingement heat transfer outperformed more than 30% compared to other orientations. The jet showed about 15% sensitivity to angular orientations.

Wing tip vortex control using synthetic jets

2006 ◽  
Vol 110 (1112) ◽  
pp. 673-681 ◽  
Author(s):  
P. Margaris ◽  
I. Gursul
Keyword(s):  
Synthetic Jet ◽  
Synthetic Jets ◽  
Tip Vortex ◽  
Particle Image Velocimetry System ◽  
Driving Frequency ◽  
Velocity Measurements ◽  
Vortex Control ◽  
Image Velocimetry ◽  
Wing Tip ◽  
Jet Blowing

AbstractAn experimental investigation was conducted to study the effect of synthetic jet (oscillatory, zero net mass flow jet) blowing near the wing tip, as a means of diffusing the trailing vortex. Velocity measurements were taken, using a Particle Image Velocimetry system, around the tip and in the near wake of a rectangular wing, which was equipped with several blowing slots. The effect of the synthetic jet was compared to that of a continuous jet blowing from the same configurations. The results show that the use of synthetic jet blowing is generally beneficial in diffusing the trailing vortex and comparable to the use of continuous jet. The effect was more pronounced for the highest blowing coefficient used. The driving frequency of the jet did not generally prove to be a significant parameter. Finally, the instantaneous and the phase-locked velocity measurements helped explain the different mechanisms employed by the continuous and synthetic jets in diffusing the trailing vortex.

Experimental Investigation of the Effect of Synthetic Jets in Minichannels With Subcooled Boiling Flow

2013 ◽  
Author(s):  
David M. Sykes ◽  
Andrew L. Carpenter ◽  
Gregory S. Cole
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Local Heat Transfer ◽  
Local Heat ◽  
High Heat ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Heat Transfer Augmentation

Microchannels and minichannels have been shown to have many potential applications for cooling high-heat-flux electronics over the past 3 decades. Synthetic jets can enhance minichannel performance by adding net momentum flux into a stream without adding mass flux. These jets are produced because of different flow patterns that emerge during the induction and expulsion stroke of a diaphragm, and when incorporated into minichannels can disrupt boundary layers and impinge on the far wall, leading to high heat transfer coefficients. Many researchers have examined the effects of synthetic jets in microchannels and minichannels with single-phase flows. The use of synthetic jets has been shown to augment local heat transfer coefficients by 2–3 times the value of steady flow conditions. In this investigation, local heat transfer coefficients and pressure loss in various operating regimes were experimentally measured. Experiments were conducted with a minichannel array containing embedded thermocouples to directly measure local wall temperatures. The experimental range extends from transitional to turbulent flows. Local wall temperature measurements indicate that increases of heat transfer coefficient of over 20% can occur directly below the synthetic jet with low exit qualities. In this study, the heat transfer augmentation by using synthetic jets was dictated by the momentum ratio of the synthetic jet to the bulk fluid flow. As local quality was increased, the heat transfer augmentation dropped from 23% to 10%. Surface tension variations had a large effect on the Nusselt number, while variations in inertial forces had a small effect on Nusselt number in this operating region.

Experimental Study of the Convective Heat Transfer From a Geometrically Scaled Up 2D Impinging Synthetic Jet

2013 ◽  
Author(s):  
Luis Silva ◽  
Alfonso Ortega ◽  
Isaac Rose
Keyword(s):  
Laboratory Experiments ◽  
Heated Surface ◽  
Target Surface ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Small Scale ◽  
Local Data ◽  
Low Frequencies ◽  
Cooling Air Flow ◽  
Cooling Air

Synthetic jets are created by periodically ejecting and injecting fluid from an orifice or channel. Despite delivering no net mass flow per cycle, a synthetic jet delivers flow with net positive momentum. Small, compact synthetic jet actuators can be fabricated to operate in the subaudible acoustic range and can be packaged in orientations that allow them to deliver cooling air flow to electronic devices. The most promising orientation is one that delivers the jet flow in a direction normal to the heated surface such that it impinges on the surface as a periodic jet. In previous studies, numerical simulations have been performed by the authors, utilizing a canonical geometry, with the purpose of eliminating actuator artifacts from the fundamental physics that drive the problem. The present paper reports on laboratory experiments that have been performed in order to nearly replicate the idealized synthetic jet geometry and thus allow comparison to the previous numerical investigations. The periodic volume change in an upstream plenum required to produce the synthetic jet is accomplished with an acoustic speaker operated at low frequencies. The amplitude and the frequency at which the jet is actuated determine the Reynolds and Strouhal numbers, which are the dominant non-dimensional groups that control the behavior of the impinging synthetic jet. By maintaining the Re and the St in the laboratory experiments to match those of the small scale actuators, the laboratory experiments have been geometrically scaled up to allow highly resolved measurements of the unsteady velocity field and the local time-dependent Nusselt number on the target heated surface. Experiments were performed at variable jet Re, frequencies, and height from the target surface. The dependence of the surface averaged Nu to jet parameters generally agrees with the computational results. However, discrepancies found between numerical and empirical local data are under revision.

A Heat Transfer Comparison Between a Synthetic Jet and a Steady Jet at Low Reynolds Numbers

2008 ◽  
Author(s):  
Rayhaan Farrelly ◽  
Alan McGuinn ◽  
Tim Persoons ◽  
Darina B. Murray
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Stroke Length ◽  
Low Reynolds Numbers ◽  
Nusselt Numbers ◽  
Significant Difference ◽  
Low Reynolds ◽  
Surrounding Fluid

A study has been carried out to compare steady jet and synthetic jet heat transfer distributions at low Reynolds numbers. Both jets issued from a 5mm diameter orifice plate with air for the steady jet being supplied by a compressor via a plenum chamber. Tests were conducted for Reynolds numbers ranging from 1000 to 4000, and for non-dimensional surface to jet exit spacings (H/D) from 1 to 6. Dimensionless stroke length (Lo/D) for the synthetic jet was held constant at 8. A significant difference was observed between the steady and synthetic jet Nusselt numbers at low Reynolds numbers and low H/D. In comparison to steady jets, the stronger entrainment of surrounding fluid and the vigorous mixing near the impingement surface are characteristics of synthetic jets that are beneficial to heat transfer. Nonetheless, the steady jet yields higher Nusselt numbers for all test conditions.

Heat Transfer Enhancement by Synthetic Jet Arrays in Air-Cooled Heat Sinks for Use in Electronics Cooling

2012 ◽  
Author(s):  
Longzhong Huang ◽  
Terrence Simon ◽  
Min Zhang ◽  
Youmin Yu ◽  
Mark North ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Channel Flow ◽  
Heat Sink ◽  
Jet Flow ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

A synthetic jet is an intermittent jet which issues through an orifice from a closed cavity over half of an oscillation cycle. Over the other half, the flow is drawn back through the same orifice into the cavity as a sink flow. The flow is driven by an oscillating diaphragm, which is one wall of the cavity. Synthetic jets are widely used for heat transfer enhancement since they are effective in disturbing and thinning thermal boundary layers on surfaces being cooled. They do so by creating an intermittently-impinging flow and by carrying to the hot surface turbulence generated by breakdown of the shear layer at the jet edge. The present study documents experimentally and computationally heat transfer performance of an array of synthetic jets used in a heat sink designed for cooling of electronics. This heat sink is comprised of a series of longitudinal fins which constitute walls of parallel channels. In the present design, the synthetic jet flow impinges on the tips of the fins. In the experiment, one channel of a 20-channel heat sink is tested. A second flow, perpendicular to the jet flow, passes through the channel, drawn by a vacuum system. Surface- and time-averaged heat transfer coefficients for the channel are measured, first with just the channel flow active then with the synthetic jets added. The purpose is to assess heat transfer enhancement realized by the synthetic jets. The multiple synthetic jets are driven by a single diaphragm which, in turn, is activated by a piezoelectrically-driven mechanism. The operating frequency of the jets is 1250 Hz with a cycle-maximum jet velocity of 50 m/s, as measured with a miniature hot-film anemometer probe. In the computational portion of the present paper, diaphragm movement is driven by a piston, simulating the experimental conditions. The flow is computed with a dynamic mesh using the commercial software package ANSYS FLUENT. Computed heat transfer coefficients show a good match with experimental values giving a maximum difference of less than 10%. The effects of amplitude and frequency of the diaphragm motion are documented. Changes in heat transfer due to interactions between the synthetic jet flow and the channel flow are documented in cases of differing channel flow velocities as well as differing jet operating conditions. Heat transfer enhancement obtained by activating the synthetic jets can be as large as 300% when the channel flow is of a low velocity compared to the synthetic jet peak velocity (as low as 4 m/s in the present study).

Sign in / Sign up

Export Citation Format

Share Document