Fine-Scale Simulation of Sandstone Acidizing

2005 ◽  
Vol 127 (3) ◽  
pp. 225-232 ◽  
Author(s):  
Chunlou Li ◽  
Tao Xie ◽  
Maysam Pournik ◽  
Ding Zhu ◽  
A. D. Hill
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Direction ◽  
Three Dimensions ◽  
Scale Model ◽  
Small Scale ◽  
Fine Scale ◽  
Homogeneous Case ◽  
The Matrix ◽  
Highly Correlated

We have developed a fine-scale model of the sandstone core acid flooding process by solving acid and mineral balance equations for a fully three-dimensional flow field that changed as acidizing proceeded. The initial porosity and mineralogy field could be generated in a correlated manner in three dimensions; thus, a laminated sandstone could be simulated. The model has been used to simulate sandstone acidizing coreflood conditions, with a 1in.diam by 2in. long core represented by 8000 grid blocks, each having different initial properties. Results from this model show that the presence of small-scale heterogeneities in a sandstone has a dramatic impact on the acidizing process. Flow field heterogeneities cause acid to penetrate much farther into the formation than would occur if the rock were homogeneous, as is assumed by standard models. When the porosity was randomly distributed (sampled from a normal distribution), the acid penetrated up to twice as fast as in the homogeneous case. When the porosity field is highly correlated in the axial direction, which represents a laminated structure, acid penetrates very rapidly into the matrix along the high-permeability streaks, reaching the end of the simulated core as much as 17 times faster than for a homogeneous case.

scholarly journals Quantification of Measurement and Model Effects in Monopile Foundation Scour Protection Experiments

2021 ◽  
Vol 9 (6) ◽  
pp. 585
Author(s):  
Minghao Wu ◽  
Leen De Vos ◽  
Carlos Emilio Arboleda Chavez ◽  
Vasiliki Stratigaki ◽  
Maximilian Streicher ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Flow Field ◽  
Three Dimensional ◽  
Small Scale ◽  
Maximum Wave Height ◽  
Chaotic Flow ◽  
The Mean ◽  
Scour Protection ◽  
Damage Number ◽  
Measurement Effects

The present work introduces an analysis of the measurement and model effects that exist in monopile scour protection experiments with repeated small scale tests. The damage erosion is calculated using the three dimensional global damage number S3D and subarea damage number S3D,i. Results show that the standard deviation of the global damage number σ(S3D)=0.257 and is approximately 20% of the mean S3D, and the standard deviation of the subarea damage number σ(S3D,i)=0.42 which can be up to 33% of the mean S3D. The irreproducible maximum wave height, chaotic flow field and non-repeatable armour layer construction are regarded as the main reasons for the occurrence of strong model effects. The measurement effects are limited to σ(S3D)=0.039 and σ(S3D,i)=0.083, which are minor compared to the model effects.

scholarly journals NUMERICAL SIMULATION OF THREE-DIMENSIONAL FLOW AROUND HARBOR DUE TO TSUNAMI USING FAVOR METHOD AND WENO SCHEME

2018 ◽  
pp. 71
Author(s):  
Yuki Kajikawa ◽  
Masamitsu Kuroiwa ◽  
Naohiro Otani
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Three Dimensional ◽  
Weno Scheme ◽  
Scale Model ◽  
Governing Equations ◽  
3D Flow ◽  
Complex Boundaries ◽  
Cartesian Coordinate ◽  
Fifth Order

In this paper, a three-dimensional (3D) tsunami flow model was proposed in order to predict a 3D flow field around a harbor accurately when tsunami strikes. In the proposed numerical model, the Cartesian coordinate system was adopted, and the Fractional Area/Volume Obstacle Representation (FAVOR) method, which has the ability to impose boundary conditions smoothly at complex boundaries, was introduced into the governing equations in consideration of applying the estimation to actual harbors with complex shape in the future. Moreover, the fifth-order Weighted Essentially Non- Oscillatory (WENO) scheme, which is a technique for achieving high accuracy even if the calculation mesh is coarse, was applied to discretization of the convection terms of the governing equations. In order to verify the validity of the model, it was applied to a large-scale laboratory experiment with a scale model of harbor. Comparisons between the simulated and experimental results showed that the model was able to reproduce the time variation of the flow field with sufficient accuracy. Moreover, the simulated results showed that a complex 3D flow field with some vertical vortex flows was generated around a harbor when tsunami struck.

scholarly journals Measurement of three-dimensional displacement field in piled embankments using synchrotron X-ray tomography

2019 ◽  
Vol 56 (6) ◽  
pp. 885-892 ◽  
Author(s):  
Louis King ◽  
Abdelmalek Bouazza ◽  
Anton Maksimenko ◽  
Will P. Gates ◽  
Stephen Dubsky
Keyword(s):  
High Resolution ◽  
Imaging Techniques ◽  
Three Dimensional ◽  
Physical Models ◽  
Scale Model ◽  
Small Scale ◽  
Full Field ◽  
X Ray ◽  
Wide Range ◽  
Piled Embankments

The measurement of displacement fields by nondestructive imaging techniques opens up the potential to study the pre-failure mechanisms of a wide range of geotechnical problems within physical models. With the advancement of imaging technologies, it has become possible to achieve high-resolution three-dimensional computed tomography volumes of relatively large samples, which may have previously resulted in excessively long scan times or significant imaging artefacts. Imaging of small-scale model piled embankments (142 mm diameter) comprising sand was undertaken using the imaging and medical beamline at the Australian Synchrotron. The monochromatic X-ray beam produced high-resolution reconstructed volumes with a fine texture due to the size and mineralogy of the sand grains as well as the phase contrast enhancement achieved by the monochromatic X-ray beam. The reconstructed volumes were well suited to the application of digital volume correlation, which utilizes cross-correlation techniques to estimate three-dimensional full-field displacement vectors. The output provides insight into the strain localizations that develop within piled embankments and an example of how advanced imaging techniques can be utilized to study the kinematics of physical models.

A generalized Archie’s law for n phases

Geophysics ◽  
2010 ◽  
Vol 75 (6) ◽  
pp. E247-E265 ◽  
Author(s):  
Paul W. J. Glover
Keyword(s):  
Volume Fraction ◽  
Three Dimensional ◽  
Three Dimensions ◽  
Reservoir Rock ◽  
Archie’S Law ◽  
Phase Volume Fraction ◽  
General Law ◽  
Special Cases ◽  
The Matrix ◽  
Definition Of

Archie’s law has been the standard method for relating the conductivity of a clean reservoir rock to its porosity and the conductivity of its pore fluid for more than [Formula: see text]. However, it is applicable only when the matrix is nonconducting. A modified version that allows a conductive matrix was published in 2000. A generalized form of Archie’s law is studied for any number of phases for which the classical Archie’s law and modified Archie’s law for two phases are special cases. The generalized Archie’s law contains a phase conductivity, a phase volume fraction, and phase exponent for each of its [Formula: see text] phases. The connectedness of each of the phases is considered, and the principle of conservation of connectedness in a three-dimensional multiphase mixture is introduced. It is confirmed that the general law is formally the same as the classical Archie’s law and modified Archie’s law for one and two conducting phases, respectively. The classical second Archie’s law is compared with the generalized law, which leads to the definition of a saturation exponent for each phase. This process has enabled the derivation of relationships between the phase exponents and saturation exponents for each phase. The relationship between percolation theory and the generalized model is also considered. The generalized law is examined in detail for two and three phases and semiquantitatively for four phases. Unfortunately, the law in its most general form is very difficult to prove experimentally. Instead, numerical modeling in three dimensions is carried out to demonstrate that it behaves well for a system consisting of four interacting conducting phases.

The Effect of Boundary Proximity Upon the Wake Structure of Horizontal Axis Marine Current Turbines

2008 ◽  
Author(s):  
L. E. Myers ◽  
A. S. Bahaj ◽  
R. I. Rawlinson-Smith ◽  
M. Thomson
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Tidal Energy ◽  
Wake Flow ◽  
Small Scale ◽  
Energy Yield ◽  
Novel Approach ◽  
Marine Current ◽  
Downstream Flow ◽  
Hydraulics Laboratory

An experimental and theoretical investigation of the flow field around small-scale mesh disk rotor simulators is presented. The downstream wake flow field of the rotor simulators has been observed and measured in the 21m tilting flume at the Chilworth hydraulics laboratory, University of Southampton. The focus of this work is the proximity of flow boundaries (seabed and surface) to the rotor disks and the constrained nature of the flow. A three-dimensional Eddy-viscosity numerical model based on an established wind turbine wake model has been modified to account for the change in fluid and the presence of a bounding free surface. This work has shown that previous axi-symmetric modelling approaches may not hold for marine current energy technology and a novel approach is required for simulation of the downstream flow field. Such modelling solutions are discussed and resultant simulation results are given. This work has been conducted as part of a BERR-funded project to develop a numerical modelling tool which can predict the flow onto a marine current turbine within an array. The work presented in this paper feeds into this project and will eventually assist the layout design of arrays which are optimally spaced and arranged to achieve the maximum possible energy yield at a given tidal energy site.

Influences of Axial Gap Between Blade Rows on Secondary Flows and Aerodynamic Performance in a Turbine Stage

2009 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
M. Kikuchi ◽  
H. Sato
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Flow ◽  
Axial Direction ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Turbine Stage ◽  
Stator Vane ◽  
Is Design ◽  
Probe Measurements

A study on the effects of the axial gap between stator and rotor upon the stage performance and flow field of a single axial flow turbine stage is presented in this paper. Three axial gaps were tested, which were achieved by moving the stator vane in the axial direction while keeping the disk cavity constant. The effect of the axial gap was investigated at two different conditions, that is design and off-design conditions. The unsteady three-dimensional flow field was analyzed by time-accurate RANS (Reynolds-Averaged Navier-Stokes) simulations. The simulation results were compared with the experiments, in which total pressure and the time-averaged flow field upstream and downstream of the rotor were obtained by five-hole probe measurements. The effect of the axial gap was confirmed in the endwall regions, and obtained relatively at off-design condition. The turbine stage efficiency was improved almost linearly by reducing the axial gap at the off-design condition.

scholarly journals Numerical analysis on the performance of Dual Rotor wind turbine

2020 ◽  
Vol 8 (03) ◽  
pp. 352-368
Author(s):  
Hazem Ali Abdel Karim ◽  
Ahmed Reda El-Baz ◽  
Nabil Abdel Aziz Mahmoud ◽  
Ashraf Mostafa Hamed
Keyword(s):  
Wind Turbine ◽  
Rotational Speed ◽  
Pitch Angle ◽  
Numerical Study ◽  
Three Dimensional ◽  
Scale Model ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Cfd Simulations

This study investigates the aerodynamic performance of wind turbines aiming to maximize the power extracted from the wind. The study is focusing on the effect of introducing a second rotor to the main rotor of the wind turbine in what is called a dual rotor wind turbine (DRWT).  The numerical study took place on the performance of small-scale model of wind turbine of 0.9 m diameter using S826 airfoil. Both the Co-rotating and Counter rotating configurations were investigated at different tip speed ratios (TSR) and compared with the performance of the single rotor wind turbine (SRWT). Many parameters were studied for dual rotor turbines. These include the spacing between the two rotors, the pitch angle of the rear rotor and the rotational speed of ratio rear to front rotor. Three-dimensional simulations performed and employed using CFD simulations with Multi Reference Frame (MRF) technique. The Co Rotating Wind Turbine (CWT) and Counter Rotating Wind Turbine (CRWT) found to have better performance compared to that of the SRWT with an increase ranging from 12 to 14% in peak power coefficient. Moreover, the effect of changing the pitch angle of the rear rotor on the overall performance found to be of a negligible effect between angles 0⁰ until 2⁰ degrees tilting toward the front rotor. On the other hand, the ratio of rotational speed of the rear rotor to the front rotor found to cause a further increase in the peak performance of the CWT and CRWT ranging from 3 to 5%.

scholarly journals EFFECT OF THE SPANWISE DISCRETISATION ON TURBULENT FLOW PAST A CIRCULAR CYLINDER

2021 ◽  
Vol 158 (A1) ◽  
Author(s):  
S Kim ◽  
P A Wilson ◽  
Z Chen
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Scale Model ◽  
Spatial Density ◽  
Eddy Simulation ◽  
Large Eddy

The effect of the spanwise discretisation on numerical calculations of the turbulent flow around a circular cylinder is systematically assessed at a subcritical Reynolds number of 10000 in the frame of three-dimensional large-eddy simulation. The eddy-viscosity k-equation subgrid scale model is implemented to evaluate unsteady turbulent flow field. Large-eddy simulation is known to be a reliable method to resolve such a challenging flow field, however, the high computational efforts restrict to low Reynolds number flow or two-dimensional calculations. Therefore, minimum spatial density in the spanwise direction or cylinder axis direction needs to be carefully evaluated in order to reduce high computational resources. In the present study, the influence of the spanwise resolutions to satisfactorily represent three- dimensional complex flow features is discussed in detail and minimum spatial density for high Reynolds flow is suggested.

scholarly journals Introduction of DMD Method to Study the Dynamic Structures of a Three-Dimensional Centrifugal Compressor with and without Flow Control

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3098 ◽  
Author(s):  
Shuli Hong ◽  
Guoping Huang ◽  
Yuxuan Yang ◽  
Zepeng Liu
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Centrifugal Compressor ◽  
Coherent Structures ◽  
Three Dimensional ◽  
Great Influence ◽  
Flow Structures ◽  
Small Scale ◽  
Dynamic Mode ◽  
Blade Tip

The flow structures around the blade tip, mainly large-scale leakage vortex, exert a great influence on compressor performance. By applying unsteady jet control technology at the blade tip in this study, the performance of the compressor can be greatly improved. A numerical simulation is conducted to study the flow characteristics of a centrifugal compressor with and without a flow control. The complex flow structures cause great difficulties in the analysis of the dynamic behavior and flow control mechanism. Thus, we introduced a dynamic flow field analysis technology called dynamic mode decomposition (DMD). The global spectrums with different global energy norms and the coherent structures with different scales can be obtained through the DMD analysis of the three-dimensional controlled and uncontrolled compressors. The results show that the coherent structures are homogeneous in the controlled compressor. The leakage vortex is weakened, and its influence range of unsteady fluctuation is reduced in the controlled compressor. The effective flow control created uniform vortex structures and improved the overall order of the flow field in the compressor. This research provides a feasible direction for future flow control applications, such as transferring the energy of the dominant vortices to small-scale vortices.

Sign in / Sign up

Export Citation Format

Share Document