The Effects of a Trip Wire and Unsteadiness on a High-Speed Highly Loaded Low-Pressure Turbine Blade

2004 ◽  
Vol 127 (4) ◽  
pp. 747-754 ◽  
Author(s):  
M. Vera ◽  
H. P. Hodson ◽  
R. Vazquez
Keyword(s):  
Boundary Layer ◽  
High Speed ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Low Pressure Turbine ◽  
Roughness Elements ◽  
Unsteady Inflow ◽  
Mach Numbers ◽  
Inflow Conditions

This paper presents the effect of a single spanwise two-dimensional wire upon the downstream position of boundary layer transition under steady and unsteady inflow conditions. The study is carried out on a high turning, high-speed, low pressure turbine (LPT) profile designed to take account of the unsteady flow conditions. The experiments were carried out in a transonic cascade wind tunnel to which a rotating bar system had been added. The range of Reynolds and Mach numbers studied includes realistic LPT engine conditions and extends up to the transonic regime. Losses are measured to quantify the influence of the roughness with and without wake passing. Time resolved measurements such as hot wire boundary layer surveys and surface unsteady pressure are used to explain the state of the boundary layer. The results suggest that the effect of roughness on boundary layer transition is a stability governed phenomena, even at high Mach numbers. The combination of the effect of the roughness elements with the inviscid Kelvin–Helmholtz instability responsible for the rolling up of the separated shear layer (Stieger, R. D., 2002, Ph.D. thesis, Cambridge University) is also examined. Wake traverses using pneumatic probes downstream of the cascade reveal that the use of roughness elements reduces the profile losses up to exit Mach numbers of 0.8. This occurs with both steady and unsteady inflow conditions.

The Effects of a Trip Wire and Unsteadiness on a High Speed Highly Loaded Low-Pressure Turbine Blade

2004 ◽  
Author(s):  
M. Vera ◽  
H. P. Hodson ◽  
R. Vazquez
Keyword(s):  
Boundary Layer ◽  
High Speed ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Low Pressure Turbine ◽  
Roughness Elements ◽  
Unsteady Inflow ◽  
Mach Numbers ◽  
Inflow Conditions

This paper presents the effect of a single spanwise 2D wire upon the downstream position of boundary layer transition under steady and unsteady inflow conditions. The study is carried out on a high turning, high-speed, low pressure turbine (LPT) profile designed to take account of the unsteady flow conditions. The experiments were carried out in a transonic cascade wind tunnel to which a rotating bar system had been added. The range of Reynolds and Mach numbers studied includes realistic LPT engine conditions and extends up to the transonic regime. Losses are measured to quantify the influence of the roughness with and without wake passing. Time resolved measurements such as hot wire boundary layer surveys and surface unsteady pressure are used to explain the state of the boundary layer. The results suggest that the effect of roughness on boundary layer transition is a stability governed phenomena, even at high Mach numbers. The combination of the effect of the roughness elements with the inviscid Kelvin-Helmholtz instability responsible for the rolling up of the separated shear layer (Stieger [1]) is also examined. Wake traverses using pneumatic probes downstream of the cascade reveal that the use of roughness elements reduces the profile losses up to exit Mach numbers of 0.8. This occurs with both steady and unsteady inflow conditions.

Highly Loaded Low-Pressure Turbine: Design, Numerical, and Experimental Analysis

2010 ◽  
Author(s):  
J. T. Schmitz ◽  
S. C. Morris ◽  
R. Ma ◽  
T. C. Corke ◽  
J. P. Clark ◽  
...  
Keyword(s):  
High Speed ◽  
Numerical Solutions ◽  
Pressure Ratio ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine ◽  
The Mean ◽  
Highly Loaded

The performance and detailed flow physics of a highly loaded, transonic, low-pressure turbine stage has been investigated numerically and experimentally. The mean rotor Zweifel coefficient was 1.35, with dh/U2 = 2.8, and a total pressure ratio of 1.75. The aerodynamic design was based on recent developments in boundary layer transition modeling. Steady and unsteady numerical solutions were used to design the blade geometry as well as to predict the design and off-design performance. Measurements were acquired in a recently developed, high-speed, rotating turbine facility. The nozzle-vane only and full stage characteristics were measured with varied mass flow, Reynolds number, and free-stream turbulence. The efficiency calculated from torque at the design speed and pressure ratio of the turbine was found to be 90.6%. This compared favorably to the mean line target value of 90.5%. This paper will describe the measurements and numerical solutions in detail for both design and off-design conditions.

The Effects of Inlet Boundary Layer Condition and Periodically Incoming Wakes on Secondary Flow in a Low Pressure Turbine Cascade

2020 ◽  
Author(s):  
Tobias Schubert ◽  
Silvio Chemnitz ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Secondary Flow ◽  
High Speed ◽  
Low Pressure ◽  
Experimental Investigations ◽  
Turbine Cascade ◽  
Flow Conditions ◽  
Low Pressure Turbine ◽  
Speed Flow ◽  
Unsteady Inflow

Abstract A particular turbine cascade design is presented with the goal of providing a basis for high quality investigations of endwall flow at high-speed flow conditions and unsteady inflow. The key feature of the design is an integrated two-part flat plate serving as a cascade endwall at part-span, which enables a variation of the inlet endwall boundary layer conditions. The new design is applied to the T106A low pressure turbine cascade for endwall flow investigations in the High-Speed Cascade Wind Tunnel of the Institute of Jet Propulsion at the Bundeswehr University Munich. Measurements are conducted at realistic flow conditions (M2th = 0.59, Re2th = 2·105) in three cases of different endwall boundary layer conditions with and without periodically incoming wakes. The endwall boundary layer is characterized by 1D-CTA measurements upstream of the blade passage. Secondary flow is evaluated by Five-hole-probe measurements in the turbine exit flow. A strong similarity is found between the time-averaged effects of unsteady inflow conditions and the effects of changing inlet endwall boundary layer conditions regarding the attenuation of secondary flow. Furthermore, the experimental investigations show, that all design goals for the improved T106A cascade are met.

High-speed boundary-layer transition induced by a discrete roughness element

2013 ◽  
Vol 729 ◽  
pp. 524-562 ◽  
Author(s):  
Prahladh S. Iyer ◽  
Krishnan Mahesh
Keyword(s):  
Boundary Layer ◽  
Shear Layer ◽  
High Speed ◽  
Roughness Element ◽  
Transition Process ◽  
Significant Rise ◽  
Boundary Layer Transition ◽  
Streamwise Vortices ◽  
Layer Transition ◽  
Mach Numbers

AbstractDirect numerical simulation (DNS) is used to study laminar to turbulent transition induced by a discrete hemispherical roughness element in a high-speed laminar boundary layer. The simulations are performed under conditions matching the experiments of Danehy et al. (AIAA Paper 2009–394, 2009) for free-stream Mach numbers of 3.37, 5.26 and 8.23. It is observed that the Mach 8.23 flow remains laminar downstream of the roughness, while the lower Mach numbers undergo transition. The Mach 3.37 flow undergoes transition closer to the bump when compared with Mach 5.26, in agreement with experimental observations. Transition is accompanied by an increase in ${C}_{f} $ and ${C}_{h} $ (Stanton number). Even for the case that did not undergo transition (Mach 8.23), streamwise vortices induced by the roughness cause a significant rise in ${C}_{f} $ until 20$D$ downstream. The mean van Driest transformed velocity and Reynolds stress for Mach 3.37 and 5.26 show good agreement with available data. Temporal spectra of pressure for Mach 3.37 show that frequencies in the range of 10–1000 kHz are dominant. The transition process involves the following key elements: upon interaction with the roughness element, the boundary layer separates to form a series of spanwise vortices upstream of the roughness and a separation shear layer. The system of spanwise vortices wrap around the roughness element in the form of horseshoe/necklace vortices to yield a system of counter-rotating streamwise vortices downstream of the element. These vortices are located beneath the separation shear layer and perturb it, which results in the formation of trains of hairpin-shaped vortices further downstream of the roughness for the cases that undergo transition. These hairpins spread in the span with increasing downstream distance and the flow increasingly resembles a fully developed turbulent boundary layer. A local Reynolds number based on the wall properties is seen to correlate with the onset of transition for the cases considered.

Boundary Layer Control on a Low Pressure Turbine Blade by Means of Pulsed Blowing

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Marion Mack ◽  
Reinhard Niehuis ◽  
Andreas Fiala ◽  
Yavuz Guendogdu
Keyword(s):  
Boundary Layer ◽  
Pressure Ratio ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Moderate Amount ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Unsteady Inflow ◽  
Inflow Conditions ◽  
Highly Loaded

The current work investigates the performance benefits of pulsed blowing with frequencies up to 10 kHz on a highly loaded low pressure turbine (LPT) blade. The influence of blowing position and frequency on the boundary layer and losses are investigated. Pressure profile distribution measurements and midspan wake traverses are used to assess the effects on the boundary layer under a wide range of Reynolds numbers from 50,000 to 200,000 at a cascade exit Mach number of 0.6 under steady as well as periodically unsteady inflow conditions. High-frequency blowing at sufficient amplitudes is achieved with the use of fluidic oscillators. The integral loss coefficient calculated from wake traverses is used to assess the optimum pressure ratio driving the fluidic oscillators. The results show that pulsed blowing with fluidic oscillators can significantly reduce the profile losses of the highly loaded LPT blade T161 with a moderate amount of air used in a wide range of Reynolds numbers under both steady and unsteady inflow conditions.

The Effects of Inlet Boundary Layer Condition and Periodically Incoming Wakes on Secondary Flow in a Low Pressure Turbine Cascade

2021 ◽  
pp. 1-12
Author(s):  
Tobias Schubert ◽  
Silvio Chemnitz ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Secondary Flow ◽  
High Speed ◽  
Low Pressure ◽  
Experimental Investigations ◽  
Turbine Cascade ◽  
Flow Conditions ◽  
Low Pressure Turbine ◽  
Speed Flow ◽  
Unsteady Inflow

Abstract A particular turbine cascade design is presented with the goal of providing a basis for high quality investigations of endwall flow at high-speed flow conditions and unsteady inflow. The key feature of the design is an integrated two-part flat plate serving as a cascade endwall at part-span, which enables a variation of the inlet endwall boundary layer conditions. The new design is applied to the T106A low pressure turbine cascade for endwall flow investigations in the High-Speed Cascade Wind Tunnel of the Institute of Jet Propulsion at the Bundeswehr University Munich. Measurements are conducted at realistic flow conditions (M2th = 0.59, Re2th = 200 000) in three cases of different endwall boundary layer conditions with and without periodically incoming wakes. The endwall boundary layer is characterized by 1DCTA measurements upstream of the blade passage. Secondary flow is evaluated by Five-hole-probemeasurements in the turbine exit flow. A strong similarity is found between the time-averaged effects of unsteady inflow conditions and the effects of changing inlet endwall boundary layer conditions regarding the attenuation of secondary flow. Furthermore, the experimental investigations show, that all design goals for the improved T106A cascade are met.

Large Eddy Simulations of a Low-Pressure Turbine: Roughness Modeling and the Effects on Boundary Layer Transition and Losses

2018 ◽  
Author(s):  
F. Hammer ◽  
Neil D. Sandham ◽  
Richard D. Sandberg
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Low Pressure ◽  
Large Eddy Simulations ◽  
Boundary Layer Transition ◽  
Immersed Boundary ◽  
Spanwise Direction ◽  
Layer Transition ◽  
Low Pressure Turbine ◽  
Large Eddy

Large eddy simulations of a linear low-pressure turbine cascade with the T106A profile and different surface roughness patches were carried out. The aim was to investigate the effects on the laminar and turbulent boundary layer on the blade suction surface. Two different approaches were used to represent the roughness patches. Firstly, a forcing model, reducing the computational costs compared to fully resolved roughness surfaces, was incorporated. Secondly, an immersed boundary method representing an as-cast roughness surface was used, for a more detailed analysis of flow mechanisms over roughness. It was found that the roughness model was able to induce boundary layer transition and alter the turbulent boundary layer, with the results in line with findings in the literature. The instantaneous flow data at different time instants of the as-cast roughness case showed the development of streaks due to distinct roughness peaks, resulting in highly uneven transition positions across the spanwise direction.

scholarly journals Description of the Flow in a Two-Stage Low-Pressure Turbine With Hub Cavities

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Maxime Fiore ◽  
Nicolas Gourdain ◽  
Jean-François Boussuge ◽  
Eric Lippinois
Keyword(s):  
Boundary Layer ◽  
Gas Turbine ◽  
Low Pressure ◽  
Secondary Flows ◽  
Boundary Layer Transition ◽  
Two Stage ◽  
Layer Transition ◽  
Low Pressure Turbine ◽  
Aspect Ratios ◽  
Multi Stage

Abstract In gas turbine, multi-stage row blading and technological effects can exhibit significant differences for the flow compared with isolated smooth blade rows. Upstream stages promote a non-uniform flow field at the inlet of the downstream rows that may have large effects on mixing or boundary layer transition processes. The rows of current turbines (and compressors) are already very closely spaced. Axial gaps between adjacent rows of approximately 1/4 to 1/2 of the axial blade chord are common practice. Future designs with higher loading and lower aspect ratios, i.e., fewer and bigger blades, and the ever present aim at minimizing engine length or compactness, will aggravate this condition even further. Interaction between cascade rows will therefore keep increasing and need to be taken into account in loss generation estimation. Also the cavities at hub platform induce purge flow blowing into main annulus and additional losses for the turbine. A robust method to account for the loss generated due to these different phenomena needs to be used. The notion of exergy (energy in the purpose to generate work) provides a general framework to deal with the different transfers of energy between the flow and the gas turbine. This study investigates the flow in a two-stage configuration representative of a low-pressure turbine including hub cavities based on large eddy simulation (LES). A description of the flow in the cavities, the main annulus, and at rim seal interface is proposed. The assessment of loss generated in the configuration is proposed based on an exergy analysis. The study of losses restricted to boundary layer contributions and secondary flows show the interaction processes of secondary vortices and wake generated in upstream rows on the flow in downstream rows.

Sign in / Sign up

Export Citation Format

Share Document