Compliant Floating-Opposing-Arm (FOA) Centrifugal Clutch

2004 ◽  
Vol 126 (1) ◽  
pp. 169-177 ◽  
Author(s):  
Nathan B. Crane ◽  
Larry L. Howell ◽  
Brent L. Weight ◽  
Spencer P. Magleby
Keyword(s):  
Experimental Data ◽  
Compliant Mechanism ◽  
Significant Cost ◽  
Body Model ◽  
Cost Reductions ◽  
Rigid Body Model ◽  
Torque Capacity ◽  
Contact Surfaces ◽  
High Torque ◽  
Assembly Analysis

This paper introduces the floating-opposing-arm (FOA) centrifugal clutch, presents a mathematical model for its analysis, and demonstrates the validity of a model to predict clutch performance with experimental data. The novelty of the clutch includes an arrangement of aggressive and non-aggressive contact surfaces in connected pairs to achieve a high torque carrying capability while maintaining starting smoothness and stability. As a compliant mechanism, it has fewer parts than traditional centrifugal clutches, and has the potential for significant cost reductions in manufacturing and assembly. Analysis of the FOA clutch is made difficult by the combination of dynamics and elastic deformation required for its operation. A model, based on the pseudo-rigid-body model, simplifies the engagement speed and torque capacity analyses. The model is validated by testing individual clutches and by demonstrating clutch designs in typical applications.

Design of a Single-Acting Constant-Force Actuator Based on Dielectric Elastomers

2008 ◽  
Author(s):  
Giovanni Berselli ◽  
Rocco Vertechy ◽  
Gabriele Vassura ◽  
Vincenzo Parenti Castelli
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compliant Mechanism ◽  
Structural Parameters ◽  
Dielectric Elastomer ◽  
Constant Force ◽  
Element Analysis ◽  
Body Model ◽  
Rigid Body Model ◽  
Supporting Frame

The interest in actuators based on dielectric elastomer films as a promising technology in robotic and mechatronic applications is increasing. The overall actuator performances are influenced by the design of both the active film and the film supporting frame. This paper presents a single-acting actuator which is capable of supplying a constant force over a given range of motion. The actuator is obtained by coupling a rectangular film of silicone dielectric elastomer with a monolithic frame designed to suitably modify the force generated by the dielectric elastomer film. The frame is a fully compliant mechanism whose main structural parameters are calculated using a pseudo-rigid-body model and then verified by finite element analysis. Simulations show promising performance of the proposed actuator.

A Simple and Accurate Method for Determining Large Deflections in Compliant Mechanisms Subjected to End Forces and Moments

1998 ◽  
Vol 120 (3) ◽  
pp. 392-400 ◽  
Author(s):  
A. Saxena ◽  
S. N. Kramer
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Elliptic Integral ◽  
Beam Equation ◽  
Large Deflections ◽  
Euler Beam ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads. Because of this fact, traditional methods of deflection analysis do not apply. Since the nonlinearities introduced by these large deflections make the system comprising such members difficult to solve, parametric deflection approximations are deemed helpful in the analysis and synthesis of compliant mechanisms. This is accomplished by representing the compliant mechanism as a pseudo-rigid-body model. A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms. In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads. A numerical integration technique using quadrature formulae has been employed to solve the large deflection Bernoulli-Euler beam equation for the tip deflection. Implementation of this scheme is simpler than the elliptic integral formulation and provides very accurate results. An example for the synthesis of a compliant mechanism using the proposed model is also presented.

A Simple and Accurate Method for Determining Large Deflections in Complaint Mechanisms Subjected to End Forces and Moments

1998 ◽  
Author(s):  
A. Saxena ◽  
Steven N. Kramer
Keyword(s):  
Rigid Body ◽  
Numerical Integration ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Beam Equation ◽  
Integration Scheme ◽  
Large Deflections ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Abstract Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads for which, traditional methods of deflection analysis do not apply Nonlinearities introduced by these large deflections make the system comprising such members difficult to solve Parametric deflection approximations are then deemed helpful in the analysis and synthesis of compliant mechanisms This is accomplished by seeking the pseudo-rigid-body model representation of the compliant mechanism A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads with positive end moments A numerical integration technique using quadrature formulae has been employed to solve the nonlinear Bernoulli-Euler beam equation for the tip deflection Implementation of this scheme is relatively simpler than the elliptic integral formulation and provides nearly accurate results Results of the numerical integration scheme are compared with the beam finite element analysis An example for the synthesis of a compliant mechanism using the proposed model is also presented.

Evaluation of Equivalent Spring Stiffness for Use in a Pseudo-Rigid-Body Model of Large-Deflection Compliant Mechanisms

1994 ◽  
Author(s):  
Larry L. Howell ◽  
Ashok Midha
Keyword(s):  
Rigid Body ◽  
Large Deflection ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Spring Stiffness ◽  
Model Concept ◽  
Analysis And Design ◽  
Body Model ◽  
Rigid Body Model ◽  
Body Joints

Abstract Compliant mechanisms gain some or all of their mobility from the flexibility of their members rather than from rigid-body joints only. More efficient and usable analysis and design techniques are needed before the advantages of compliant mechanisms can be fully utilized. In an earlier work, a pseudo-rigid-body model concept, corresponding to an end-loaded geometrically nonlinear, large-deflection beam, was developed to help fulfill this need. In this paper, the pseudo-rigid-body equivalent spring stiffness is investigated and new modeling equations are proposed. The result is a simplified method of modeling the force/deflection relationships of large-deflection members in compliant mechanisms. Flexible segments which maintain a constant end angle are discussed, and an example mechanism is analyzed. The resulting models are valuable in the visualization of the motion of large-deflection systems, as well as the quick and efficient evaluation and optimization of compliant mechanism designs.

Compliant Pantographs via the Pseudo-Rigid-Body Model

1998 ◽  
Author(s):  
Andrew J. Nielson ◽  
Larry L. Howell
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Test Results ◽  
Rigid Link ◽  
Body Model ◽  
Design Flexibility ◽  
Model Predictions ◽  
Rigid Body Model ◽  
Classical Mechanism

Abstract This paper uses a familiar classical mechanism, the pantograph, to demonstrate the utility of the pseudo-rigid-body model in the design of compliant mechanisms to replace rigid-link mechanisms, and to illustrate the advantages and limitations of the resulting compliant mechanisms. To demonstrate the increase in design flexibility, three different compliant mechanism configurations were developed for a single corresponding rigid-link mechanism. The rigid-link pantograph consisted of six links and seven joints, while the corresponding compliant mechanisms had no more than two links and three joints (a reduction of at least four links and four joints). A fourth compliant pantograph, corresponding to a rhomboid pantograph, was also designed and tested. The test results showed that the pseudo-rigid-body model predictions were accurate over a large range, and the mechanisms had displacement characteristics of rigid-link mechanisms in that range. The limitations of the compliant mechanisms included reduced range compared to their rigid-link counterparts. Also, the force-deflection characteristics were predicted by the pseudo-rigid-body model, but they did not resemble those for a rigid-link pantograph because of the energy storage in the flexible segments.

Large Stroke Series Compliant Mechanism

2012 ◽  
Vol 490-495 ◽  
pp. 1104-1108 ◽  
Author(s):  
Ming Cai Shan ◽  
Wei Ming Wang ◽  
Shu Yuan Ma ◽  
Shuang Liu
Keyword(s):  
Theoretical Model ◽  
Maximum Stress ◽  
Compliant Mechanism ◽  
Critical Parameters ◽  
Element Analysis ◽  
Flexure Hinges ◽  
Body Model ◽  
System A ◽  
Rigid Body Model ◽  
The Difference

To increase the stroke of precision positioning system, a novel series compliant mechanism is presented which is based on elliptical flexure hinges. Pseudo-rigid-body model and energy method are applied to establish the theoretical model of stiffness and maximum stress, which are critical parameters for the large stroke compliant mechanism. The relationships are analyzed between geometric parameters of the series complaint mechanism, stiffness and maximum stress. According that, the series compliant mechanism is designed with the stroke more than 5mm and stiffness less than 3.2N/mm. The difference is less than 5% between the results of finite element analysis and theoretical model computation, which proves the correctness of the application design.

On the Comparison of the Pseudo Rigid Body Model Method and the Finite Element Method for a 3DOF Planar Micro-Motion Stage

2000 ◽  
Author(s):  
J. Zou ◽  
L. G. Watson ◽  
W. J. Zhang
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Compliant Mechanism ◽  
The Finite Element Method ◽  
Real Time Control ◽  
Body Model ◽  
Time Control ◽  
Rigid Body Model ◽  
Micro Motion ◽  
Element Method

Abstract This paper discusses one type of commonly used parallel manipulator mechanism for the generation of micro-motion. This mechanism is designed as a compliant mechanism. The design and control of such a compliant mechanism is an important issue. This paper focuses on kinematic issues with consideration of future real-time control of the system. In particular, a constant-Jacobian method to approximate the kinematics, which is based on a pseudo rigid body model of the compliant mechanism, is further validated. This validation is based on the difference between this approximate method and the finite element method to the actual device, for an actuator range of 0–15 μm. The computational time with this approximate method is nearly 50 times less than that with the finite element method. It is expected that this approximation method will be far superior to the finite element method in terms of real-time control.

Classification of Compliant Mechanisms and Determination of the Degrees of Freedom Using the Concepts of Compliance Number and Pseudo-Rigid-Body Model

2019 ◽  
Author(s):  
Pratheek Bagivalu Prasanna ◽  
Ashok Midha ◽  
Sushrut G. Bapat
Keyword(s):  
Rigid Body ◽  
Degrees Of Freedom ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Body Model ◽  
Active Compliance ◽  
Kinematic Behavior ◽  
Rigid Body Model

Abstract Understanding the kinematic properties of a compliant mechanism has always proved to be a challenge. A concept of compliance number offered earlier emphasized the development of terminology that aided in its determination. A method to evaluate the elastic degrees of freedom associated with the flexible segments/links of a compliant mechanism using the pseudo-rigid-body model (PRBM) concept is provided. In this process, two distinct classes of compliant mechanisms are developed involving: (i) Active Compliance and (ii) Passive Compliance. Furthermore, these also aid in a better characterization of the kinematic behavior of a compliant mechanism. A more lucid interpretation of the significance of compliance number is provided. Applications of this method to both active and passive compliant mechanisms are exemplified. Finally, an experimental procedure that aids in visualizing the degrees of freedom as calculated is presented.

scholarly journals Design and Validation of a Single-SOI-Wafer 4-DOF Crawling Microgripper

Micromachines ◽  
2019 ◽  
Vol 10 (6) ◽  
pp. 376 ◽  
Author(s):  
Matteo Verotti ◽  
Alvise Bagolini ◽  
Pierluigi Bellutti ◽  
Nicola Pio Belfiore
Keyword(s):  
Finite Element Analysis ◽  
Rigid Body ◽  
Compliant Mechanism ◽  
Silicon On Insulator ◽  
Element Analysis ◽  
Deep Reactive Ion Etching ◽  
Theoretical Simulation ◽  
Body Model ◽  
Replacement Method ◽  
Rigid Body Model

This paper deals with the manipulation of micro-objects operated by a new concept multi-hinge multi-DoF (degree of freedom) microsystem. The system is composed of a planar 3-DoF microstage and of a set of one-DoF microgrippers, and it is arranged is such a way as to allow any microgripper to crawl over the stage. As a result, the optimal configuration to grasp the micro-object can be reached. Classical algorithms of kinematic analysis have been used to study the rigid-body model of the mobile platform. Then, the rigid-body replacement method has been implemented to design the corresponding compliant mechanism, whose geometry can be transferred onto the etch mask. Deep-reactive ion etching (DRIE) is suggested to fabricate the whole system. The main contributions of this investigation consist of (i) the achievement of a relative motion between the supporting platform and the microgrippers, and of (ii) the design of a process flow for the simultaneous fabrication of the stage and the microgrippers, starting from a single silicon-on-insulator (SOI) wafer. Functionality is validated via theoretical simulation and finite element analysis, whereas fabrication feasibility is granted by preliminary tests performed on some parts of the microsystem.

Preliminaries for a Spherical Compliant Mechanism: Pseudo-Rigid-Body Model Kinematics

2007 ◽  
Author(s):  
Saurabh Jagirdar ◽  
Craig P. Lusk
Keyword(s):  
Rigid Body ◽  
Compliant Mechanism ◽  
Beam Angle ◽  
Body Model ◽  
Spherical Mechanisms ◽  
Characteristic Radius ◽  
Rigid Body Model ◽  
Limiting Case

The kinematic portion of a pseudo-rigid-body model (PRBM) is developed as a generalization from planar to spherical mechanisms. The topology of the spherical compliant segment and its rigid-body equivalent are derived from planar models by analogy. The nomenclature for the spherical PRBM is chosen to facilitate comparison with the planar PRBM. The motion of the compliant segment is calculated using FEA and PRBM parameters are determined. The characteristic radius and parametric angle coefficient are found to decrease as the angle subtended by the beam increases. The parameterization limit increases with increasing beam angle. The spherical PRBM is identical to the planar PRBM in the limiting case when beam angles become very small.

Sign in / Sign up

Export Citation Format

Share Document